Metering ƈ If you cannot obtain suitable exposure conditions, you can change the metering method to take brighter pictures. [MULTI] : Exposure will be calculated based on an average of the available light in the image area. However, METERING the calculation will be biased towards the centre of MULTI CENTER-WEIGHTED the image area. This is suitable for general use. SPOT [CENTER-WEIGHTED] : Exposure will be calculated based on an average of the available light in the image area.
Sharpness ƈYou can adjust the sharpness of the picture you want to take. You cannot check the sharpness effect on the LCD monitor before you take a picture, because this function is applied only when the captured image is stored on the memory. Sub menu Icon SHARPNESS SOFT NORMAL VIVID Description The edges of the image are softened. SOFT This effect is suitable for editing images on your PC. The edges of the image are sharp. NORMAL This is suitable for printing.
Save / Load a specific camera configuration (MySET) ƈ Use the MySET mode to save frequently used camera settings (Save Myset) and use it later (Load Myset) ƃ Saving the camera configuration : 1. Use the camera buttons and menu to set desired camera configuration. MYSET 2. Select the Program mode and press the Menu button. MYSET1 SAVE MYSET2 LOAD 3. Press the Left/Right buttons to select the [MYSET] menu tap. MYSET3 4. Select the [SAVE] menu by pressing the Up / Down button and press the Right button.
Starting play mode ƈIf the memory card is inserted in the camera, all the camera functions apply only to the memory card. ƈIf the memory card is not inserted in the camera, all the camera functions apply only to the internal memory. ƈIf you have turned on the camera by pressing the POWER button, you can press the PLAY MODE button once to switch to Play mode and press it again to switch to Recording mode. ƈYou can turn the power on with the play mode button. The camera is turned on in play mode.
Starting play mode ƃPlaying back a movie clip Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded movie clip that you want to play back by using the LEFT/ RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a movie clip file. - To pause a movie clip file while playing it back, press the play & pause button again.
Starting play mode ƈOn camera movie trimming : You can extract desired frames of movie clip during the movie clip play back. 1. Select a desired movie clip in the play mode. 2. Play back the movie clip by pressing the Play & Pause button. 3. Press the Pause button at the point of the movie clip that you want to start extracting. 4. Press the zoom T button. 5. Press the Play & Pause button and the extracted range will be displayed on the status bar. TRIM : T CAPTURE:E 6.
Starting play mode ƃPlaying back a recorded voice Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded voice that you want to play back by using the LEFT/ RIGHT button. If you select a recorded voice file, the voice indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a recorded voice file. - To pause a recorded voice file, while playing it back, press the play & pause button again.
LCD monitor indicator ƈThe LCD monitor displays shooting information about the displayed image. ۀ ڹ ں ڻ ڼ ڽ ھ ڿ No. Description Icon 1 Play mode - 2 Battery p.17 3 Movie clip / Voice memo - 4 Protect indicator p.85 5 DPOF indicator p.86 6 Remote control indicator - 7 Memory card indicator - 8 Folder name and Stored image number 100-0012 Page - ƈ Select the [IMAGE INFORMATION] sub menu of the [OSD INFORMATION] menu and you can check the recording information.
Using the camera buttons to adjust the camera ƈIn Play mode, you can use the buttons on the camera to conveniently set up the Play mode functions. Thumbnail( )/ Enlargement( ) button ƃYou can view multiple pictures, enlarge a selected picture, and crop and save a selected area of an image. ƃThumbnail display 1. While an image is displayed full screen, press the thumbnail button. 2. The thumbnail display will highlight the image that had been showing at the time the thumbnail mode was selected. 3.
Thumbnail( ) / Enlargement( ) button ƃThe maximum enlargement rate in proportion to the image size. Image size 5M 4M 3M 2M 1M VGA Maximum Normal angle enlargement Wide angle rate X9.0 X6.45 X5.3 X5.0 X4.0 X3.3 X4.6 X4.2 X3.6 X3.5 X2.5 X2.4 ƃTrimming : You can extract part of the image that you want and save it separately. TRIMMING? 1. Select an image that you want to enlarge and press TRIM CANCEL the enlargement button. CONFIRM:OK 2.
Voice ( ) memo / Up button 3. Press the shutter button to start recording and voice will be recorded to the still image for 10 seconds. While the voice is recording, the recording status window will be displayed as shown alongside. STOP : SHUTTER 4. The recording can be stopped by pressing the shutter button again. 5. The ( ) icon will be displayed on the LCD monitor after voice memo recording has finished. - Voice memos can’t be recorded onto movie clip and voice recording files.
Delete ( ) button ƈThis deletes images stored on the memory. ƃDeleting Images in Play Mode 1. Select an image that you want to delete by pressing the LEFT/ RIGHT button and press the DELETE( ) button. 2. A message will display as shown alongside on the LCD monitor. 3. Select the submenu values by pressing the UP/ DOWN button and then press the OK button. If [DELETE] is selected: deletes the selected images. If [CANCEL] is selected : cancels "Delete Image".
Red eye / Printer button ( ) ƈ When an image that have Red-eye effect (When taking a people or animal with a photographic flash, the eye will be red) plays back, this button will remove the red colour. 1. In the Play mode, select an image that has red-eye effect by pressing the Left / Right button. 2. Press the Red eye button ( ) and a menu bar for removing the red-eye effect will display. SAVE:OK [An image that has red-eye effect] CANCEL:E [An image removed the red-eye effect] 3.
Left / Right / Menu / OK button ƈ LEFT / RIGHT/ MENU/ OK buttons activate the following. - LEFT button - RIGHT button - MENU button - OK button ŝ74Ş : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor. While the menu is not showing, press the LEFT button to select the previous image. : While the menu is showing, press the RIGHT button to select the menu tab to the right of the cursor, or to move an secondary menu.
Album button ƈYou can organise the captured still images (except for the TIFF file) into albums by using the Album button. ƈThis camera has 8 albums and each album can take up to 100 images. ƈThe album menu loading time depends on the memory card type. ƈHow to use the album ƃSelecting the album 1. In the play mode, press the Album button. 2. Select the ALBUM menu by pressing the Left/ Right button. SELECT : OK 3. Select a desired album by pressing the Up/Down button.
Album button 4. Press the OK button and a confirmation window for inserting an image will display. Select a desired sub menu by Pressing the Up/Down button and press the OK button. [YES] : inserts an image into the selected album. [NO] : cancels the inserting image. ƃRemoving still images from the album 1. Select an album. 2. Press the delete button and a confirmation window will display. 3. Select a desired sub menu by pressing the Up/ Down button and press the OK button.
Album button ƃPlaying back the albums Ƅ Playing back all of the albums 1. Select ( ) album. 2. Select SHOW menu by pressing the Left/ Right button. 3. Select a desired sub menu by pressing the Up/ Down button. Press the OK button and the slide show will start. ( ) : The slide show is closed after one cycle. ( ) : The slide show is repeated until the OK button is PLAY:OK pressed. Ƅ Playing a desired album 1. Select a desired album. 2. Select SHOW menu by pressing the Left/ Right button. 3.
Remote control ƈ After connecting the camera with an external monitor, you can see the captured image by using the remote control. ƈ Remote control is optional in some countries. ƈ In play mode, you can use the remote control to set up the play mode functions. Enlargement button Thumbnail button Display / Information button Up / Down / Left / Right button Play & Pause button ƈ See below for operation of buttons - Enlargement button : In play mode, this button enlarges the selected image.
Remote control - Display / Information button : In play mode, you can view the information of the selected image by pressing this button. - Up / Down/ Left / Right button : In play mode, you can select a still image or movie clip by pressing the Left/ Right button. In play mode, different parts of the enlarged image can be viewed by pressing these buttons. In the thumbnail mode, you can move to a desired image by pressing these buttons.
Setting up the play back function using the LCD monitor ƈPLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY button.
Setting up the play back function using the LCD monitor ƈThis menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Menu tab Main menu IMAGES AUTO SET Sub menu Secondary menu ONE PIC - ALL PICS - NO - YES - Page p. 92 p. 93 AUTO POSTCARD CARD LETTER SIZE 4X6 L 2L A4 A3 AUTO CUSTOM SET FULL p. 93 1 2 LAYOUT 4 8 9 16 AUTO TYPE PLAIN PHOTO FAST PHO.
Setting up the play back function using the LCD monitor Menu tab Main menu Sub menu Secondary menu Page AUTO DRAFT QUALITY NORMAL FINE AUTO p. 93 CUSTOM SET DATE OFF ON AUTO FILE NAME OFF ON STANDARD - INDEX - NO - YES - NO - YES - PRINT DPOF PRINT p. 94 p. 94 RESET ſ Menus are subject to change without prior notice. ŝ82Ş p.
Rotating an image ƈ You can rotate the stored images by various degrees. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [ROTATE] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
Resize ƈChange the resolution (size) of pictures taken. Select [USER IMAGE] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [RESIZE] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Protecting images ƈThis is used to protect specific shots from being accidentally erased (LOCK). It also unprotects images that have been previously protected (UNLOCK). ƃProtecting Images PROTECT SELECT 1. Press the play mode button and press the menu button. ALL 2. Press the LEFT/ RIGHT button and select the [PROTECT] menu tab. EXIT:MENU MOVE: 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Deleting all images ƈOf all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place. The startup image is stored in the camera's internal memory (i.e., not on the memory card) and it will not be deleted even if you delete all files on the memory card. ƃDeleting all images 1. Press the play mode button and press the menu button.
DPOF : STANDARD ƈThis function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] DPOF menu tab. STANDARD ONE PIC 3. Select the [STANDARD] menu by pressing the INDEX ALL PICS PRINT SIZE UP/ DOWN button and press the RIGHT button. CANCEL 4. Use the UP and DOWN buttons to select [ONE PIC] or BACK: SET:OK [ALL PICS], and then press the OK button.
DPOF : PRINT SIZE ƈYou can specify the print size when printing images stored on the memory card. The [PRINT SIZE] menu is available only for DPOF 1.1 compatible printers. ƃSetting the Print Size 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [PRINT SIZE] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
On Screen Display information ƈ You can check shooting information about the displayed image. 1. Press the play mode button and press the menu button. 2. Select the [OSD INFORMATION] menu tab by pressing the LEFT/ RIGHT button. 3. Select a desired sub menu by pressing the UP/ DOWN button. - [FULL OSD] : All information shown as below is displayed. - [BASIC OSD] : Some information shown as below is displayed. - [IMAGE INFORMATION] : Shooting information about the displayed image is displayed.
Copy To Card ƈ This enables you to copy image files, movie clips and voice recording files to the memory card. ƃ Copying to the Memory Card 1. Press the play mode button and press the menu button. 2. Select the [COPY TO CARD] menu tab by pressing the COPY TO CARD LEFT/ RIGHT button. NO YES 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [NO] : Cancels "Copy to Card".
PictBridge ƈ You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. Movie clips and voice files cannot be printed. ƃ Setting up the camera for connection with the printer 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select [SETUP] menu tab. 3. Select [USB] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
PictBridge : Picture Selection ƈ Easy printing When you connect the camera to printer in the Play back mode, you can print a picture easily. - Pressing the shutter button : Currently displayed image will be printed with the printer’s default setting. - Pressing the Left/ Right button : Selects a previous/ next image. PRINT:SHUTTER MENU:OK ƈ Select pictures to print 1. Press the Menu button. 2. The [IMAGES] menu will appear. IMAGES 3.
PictBridge : Print Setting ƈ AUTO SET 1. Use the LEFT and RIGHT buttons to select the [AUTO SET] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [NO] : [CUSTOM SET] values are kept. [YES] : All values in the [CUSTOM SET] are automatically changed. AUTO SET NO YES MOVE: ƈ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print Quality, Date Print, and File Name Print menus for printed pictures. 1.
PictBridge : Printing ƈ When the wide angle image is printed as a real size, 8% of the left and right side of the image may not be printed. Check that your printer can support the wide angle image when you print the image. When you print the image on the photo labs, ask them the image has to be printed as a wide angle image. (Some photo labs may not support the wide angle size print.) ƈ Printing Pictures 1. Use the LEFT and RIGHT buttons to select the [PRINT] menu tab. 2.
PictBridge : RESET ƈ Initialises user-changed configurations. 1. Use the LEFT and RIGHT buttons to select the [RESET] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. If [NO] is selected : Settings will not be reset. If [YES] is selected : All print and image settings will be reset. RESET NO YES MOVE: ſ Default print setting varies depending on the printer manufacturer.
Setup menu ƈIn this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. Menu tab Main menu FILE PWR SAVE Sub menu Secondary menu SERIES - RESET - OFF, 1, 3, 5MIN - Page p.97 p.98 ENGLISH ጥૹ FRANÇAIS DEUTSCH ESPAÑOL ITALIANO P”CCK»… PORTUGUÊS DUTCH DANSK SVENSKA SUOMI ⁹ᷘ LANGUAGE p.
Setup menu Menu tab Main menu Sub menu DARK - LCD NORMAL - VIDEO Q.VIEW RESET Secondary menu BRIGHT - NTSC - PAL - OFF, 0.5, 1, 3SEC - NO - YES - Page p.102 p.103 p.105 p.105 ſ Menus are subject to change without prior notice. File name ƈ This function allows the user to select the file naming format. ƃ Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. SETUP 2.
File name INFORMATION ƃThe first stored folder name is 100SSCAM, and the first file name is SL550001. ƃ File names are assigned sequentially from SL550001 ƍ SL550002 ƍ ~ ƍ SL559999. ƃThe folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM ƍ 101SSCAM ƍ ~ ƍ 999SSCAM. ƃThe files used with the memory card conform to the DCF(Design rule for Camera File systems) format.
Language ƈThere is a choice of languages that can be displayed on the LCD monitor. Even if the battery is removed and inserted again, the language setting will be preserved. ƃSetting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. SETUP 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. FILE ENGLISH PWR SAVE 3. Select the [LANGUAGE] menu by pressing the ጥૹ LANGUAGE FRANÇAIS UP/ DOWN button and press the RIGHT button.
Setting up the Date / Time / Date type ƈYou can change the date and time that will be displayed on the captured images and set up the date type. ƃSetting Date / Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. SETUP 2. Press the LEFT/ RIGHT button and select the [SETUP] FILE 05/08/01 13:00 PWR SAVE menu tab. LANGUAGE YYYY/MM/DD 3. Select the [DATE&TIME] menu by pressing the FORMAT DATE&TIME UP/ DOWN button and press the RIGHT button.
Auto Focus lamp ƈYou can turn on and off the Auto Focus lamp ƃHow to set up the lamp 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [AF LAMP] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [OFF] is selected : The AF lamp will not light up. If [ON] is selected : The AF lamp will light up.
Connecting an External Device (USB) ƈ You can select an external device to which you want to connect the camera using the USB cable. ƃ Selecting an External Device 1. In any mode with the exception of Voice Recording mode, press the MENU button. SETUP 2. Press the LEFT/ RIGHT button and select the [SETUP] DATE&TIME COMPUTER IMPRINT PRINTER menu tab. AF LAMP SOUND 3. Select the [USB] menu by pressing the UP/ DOWN button USB and press the RIGHT button. BACK: SET:OK 4.
Selecting Video out type ƈ The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. ƃ Setting the Video Out Type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] menu tab. 3. Select the [VIDEO] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Selecting Video out type INFORMATION ƃ NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico. ƃ PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland, Thailand, Norway. ƃ When using a TV as an external monitor, you will need to select the external or AV channel of the TV. ƃ There will be a digital noise on the external monitor, but it is not a malfunction.
Quick view ƈ If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Q.VIEW] setup. Quick view is possible only with still images. ƃ Setting Quick View 1. In any mode with the exception of Voice Recording mode, press the MENU button. SETUP 2. Press the LEFT/ RIGHT button and select the [SETUP] SOUND OFF USB 0.5 SEC menu tab. LCD 1 SEC VIDEO 3. Select the [Q.VIEW] menu by pressing the UP/ DOWN 3 SEC Q.
Setting up the Mycam menu ƈ You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu S.IMAGE S.SOUND SH.SOUND Sub menu Page OFF LOGO USER IMAGE 1 USER IMAGE 2 OFF SOUND 1 SOUND 2 SOUND 3 OFF SH.SOUND 1 SH.SOUND 2 SH.SOUND 3 p.106 p.107 p.107 ſ Menus are subject to change without prior notice.
Start up sound ƈ You can select the sound that is activated whenever the camera is turned on. ƃ Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [MYCAM] menu tab. 3. Select the [S.SOUND] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
Important notes Be sure to observe the following precautions! ƈThis unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes ƈCaution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens. - When the lens cover opens, the outer lens that you can see is for auto focus. When using or cleaning this camera, handle the outer lens with care. ƈIf the digital camera is not used for a long period, an electric discharge can occur.
Warning indicator ƈThere are several warnings that may appear on the LCD display CARD ERROR! ϛMemory card error ƍ Turn off the camera power and turn it on again ƍ Insert the memory card again ƍ Insert the memory card and format the memory card (p.99) MEMORY ERROR! ϛInternal memory error ƍ Turn off the camera power and turn it on again ƍ Format the memory with the memory card removed. (p.
Warning indicator LOW LIGHT! ϛWhen taking pictures in dark places ƍ Take pictures in Flash Photography mode. OUT OF NUMBER ϛWhen selecting too many printing pages in the PictBridge menu. ƍ Select printing page within the limitation. Before contacting a service centre ƈPlease check the following The camera doesn’t switch on ϛThere is low battery capacity ƍ Insert charged battery (p.
Before contacting a service centre Camera does not take images when pressing the Shutter button ϛThere is insufficient memory capacity ƍ Delete unnecessary image files ϛThe memory card has not been formatted ƍ Format the memory card (p.99) ϛThe memory card is exhausted ƍ Insert a new memory card ϛThe memory card is locked ƍ Refer to [CARD LOCKED!] error message (p.110) ϛThe camera’s power is off ƍ Turn the camera power on ϛThe battery are exhausted ƍ Insert charged battery.
Before contacting a service centre The camera buttons do not operate ϛCamera malfunction ƍ Remove /re-insert battery and switch the camera on A card error has occurred while the memory card is in the camera.
Specifications Type Image Sensor Effective Pixel Total Pixel 1/2.5ůCCD Approx. 5.0 Mega-pixel Approx. 5.2 Mega-pixel SHD Lens f = 4.6 ~ 22.2mm Focal Length (35mm film equivalent : 28~135 mm) Lens F No. F 3.3 ~ F 4.8 Still Image mode : 1.0X ~ 5.0X, Movie Clip mode : 1.0X ~ 2.0X Digital Zoom Play mode : 1.0X ~ 9.0X (depends on image size) Viewfinder LCD Monitor 2.
Specifications Media File Format Internal memory : Approx. 24MB flash memory External memory : SD Card/MMC (Up to 1GB guaranteed) Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.
Software Notes Please ensure that you read the instruction manual carefully before use. ϛThe attached software is a camera driver and image editing software tool for Windows. ϛUnder no circumstances should all or part of either the software or the user manual be reproduced. ϛCopyrights for software are licensed only for use with a camera. ϛIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the software CD provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. ƈ Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION ƃ Close other programs before installing the application software. ƃ Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.
Setting up the application software 4. A window will open. Click the [Next(N) >] button. [ቄඁ!] 5. DirectX Installation is completed. Click the [Finish] button and then the QuickTime installation will be started. * The system will not reboot even if you click the [Finish] button. * The screen shot of step 5 can be different from the illustration depending on the system requirements. [Click !] 6. Click [Next >] to begin installing QuickTime. [Click !] 7. A Welcome window will appear.
Setting up the application software 8. The Software License Agreement window will open, asking you to agree to the licensing. Use the button on the bottom left to select the language of your choice, and then click [Agree] to accept the license agreement. The installation will proceed to the next stage. If you do not agree to the license agreement, click [Disagree]. The installation will be canceled. If the language of your choice is not listed, please select [English]. 9.
