FCC TEST REPORT Report No.: EMC-FCC-R0176 http://www.emc2000.co.kr User Manual EMC compliance Ltd. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-390, Korea 82-31-336-9919 (Main) 82-505-299-8311 (Fax) This test report shall not be reproduced, except in full, Without the written approval.
SAMSUNG SMARTCAM User Manual 0678 ! SNH-E6440BN
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
• Especially, the power cord should be installed carefully while keeping it out of children’s reach. • Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture. • The product is designed for outdoor use. • The product is not designed for medical monitoring, and requires a grown-up’s protective supervision on its use.
Features 01 GETTING STARTED Features What’s Included 5 Part names and functions 6 Power Supply Network connection 4 · English 4 7 7 • Easy to install - Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program. • Remote monitoring - Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you. - PC, laptop or smart phone can be used for monitoring.
What’s Included Check for components when opening the product package. 01 Getting Started 9 n ` Body & Bracket Camera Power Adaptor Network Cable Quick Start Guide Warranty Card GPL Lisence Tapping screw Please save the packaging. You will need the serial number later to register the camera.
Part names and functions Wi-Fi Direct button Camera connector Create a Wi-Fi connection for your camera and smart phone. Connect the camera via the RJ-12 cable. Audio Input Connect to the Mic. Power / Network status LED Audio Output Connect to the speaker. Network port Used for wireless connection. 9 Power connection terminal Connect to the power adaptor. Camera lens Reset button Resets the camera settings to the default. Press and hold for about 10 seconds to reboot the system.
Power Supply Network connection Plug-in the camera power adapter to the wall outlet and connect the camera as shown. n Make sure to use the provided power adaptor. If you use an adaptor other than the power supply adaptor provided in our package, the product may not operate properly. ` ` It will take about 1min for the camera to boot-up completely. When the camera has finished turning on, the LED lamp turns red and starts blinking.
Installation Precautions 02 INSTALLATION & NETWORK CONNECTION Installation Precautions Wall Mounting with Screws Adjusting the Angle Network Connection and Settings Precautions Connecting via network cable Wi-Fi connection setting 8 · English 8 8 9 10 10 10 11 11 1. Install the camera in a place where the Wi-Fi signal can be reached and without interference. 2. Keep it away from humidity such as around the humidifier. 3.
Assembling Installing the camera 1. Match the home of the main unit and the bracket. 3. 2. Please engage the bracket body and return to the [CLOSE] direction using a flathead screwdriver 2. ` Turn to [OPEN] direction to remove the body and bracket. Choose the location where you want to install the camera. 4. Use the provided mounting screws to attach the camera to a wall or ceiling. 02 Connect the [CAM] on the side of the main terminal and the camera cable.
Network Connection and Settings Precautions • The wireless network access may fail, depending on the communications environment. • For details about the network settings and password, contact your network administrator or service provider. • For a specific Internet service requiring user authentication, you may not access the service. If this is the case, contact the service provider. • Do not access the unauthorized network.
Wi-Fi connection setting If you want to connect a camera to Wi-Fi, first connect the network cable and try to make a connection to the Wi-Fi network. 1. When you apply the power, the power status LED is lit red, and it will change to red blinking when the booting is completed. 2. Use the network cable (LAN cable) to connect the LAN port of the unit to the LAN port of the Wireless Access Point. 02 Internet Service 3. Register and select the camera according to guide of 03. Monitoring. 4.
Registration MONITORING Registration Web browser requirements Starting SmartCam Live Video Monitoring options Setup Basic Info Network Time Alarm & Notification Alarm Schedule SD card 12 · English 12 12 12 03 Event Alarm 27 Playback 27 17 18 20 20 21 23 24 25 26 Information My Account Support 28 28 29 Once you register the product with the site, you can monitor the camera video on the PC or laptop computer.
❖ Plug in installation 3) Click to begin the installation. 4) Installation has completed. You need to install your plug in to automatically search for cameras connected to the network and view the video in your camera. n 1) ` If you login or click in a PC where the plug in is not installed, the installation message window will pop up. ` When you install the plug in, the web browser will be terminated and you need to launch it again.
For Mac 2) Click . 3) Click . 14 · English 4) Enter MAC PC password and click . 5) Installation has completed.
5. 6. According to the network connection and setting, click when the camera LED turns into green. • ID : Using alphabetical characters and numbers, make a combination using 8 to 14 letters. • Password : To strengthen security, create a password with a combination of special characters, numerals and English letters. 7. Select the serial number of the camera to be added from the camera search list. If the camera is not found, enter the serial number manually. J ` 8. Click .
9. Create and . 10. Click . n ` ` 12. Select your Wireless Network from the list. 13. Enter the password of your Wireless Network and click . The camera password is used to block the unauthorized access to your camera. Create camera password using alphanumeric characters between 1 to 8 without any space. 11. After adding the camera, click in the wireless network setup pop-up window.
15. Unplug the network cable from the camera and the router. 16. Click if the button is activated. Live Video 1. 17. Once the camera is successfully registered, you can check the camera in the camera list. Select a camera from the camera list at the upper left hand of the screen. n Enter the camera password and click . n 3. 03 The gray icon indicates the camera is inactive so you cannot monitor it right now.
Item Monitoring options bc Description Motion zone setting It detects motion within the range set by a user. Flip You can flip over the video image. A user can directly save videos in their SD card. n m Item Default Camera Set the default camera to monitor in the camera list. b Delete Camera Delete the registered camera. c Cancel remembering camera password Cancel remembering the camera password.
❖ Network Speed Profile Name ❖ Motion detection area setting Resolution Frame rate Recommended bandwidth Low Speed Network VGA 20 fps 0.7Mbps Mid Speed Network HD(720P) 15 fps 1Mbps High Speed Network Full HD(1080P) 20 fps 2.8Mbps n 1) Click the < 2) Drag it to the screen to set the detection area. Click on . If you want to delete the set area, click on .
Item Description Setup Serial number You can confirm the serial number. Basic Info b Camera password Click the , you can change the Camera password. Enter the current camera password, and type a new Camera password. c Camera Name Click the , you can change the camera name. Firmware Version You can check the current version and the latest version of your camera S/W. Status LED You can turn on/off the LED in your camera.
❖ Firmware update Network If the currently used S/W is not of the latest version, update it. If you are using the latest version, then the firmware will not be activated. 1) Click . 2) Click the < 3) When the firmware update is finished, the camera will reboot. b > icon to update the firmware. ` If you want to update the firmware, it is recommended to use a wired network connection. ` ` If the power goes off during updates, it may not operate properly.
n ` ` If any of the manual settings is wrong, the network settings will not be applied. If you have both cable and wireless network connections simultaneously, the cable network connection is prioritized. ` If you switch from the current wireless connection to the cable connection, the network will switch to cable connection accordingly. ` For more information about the router or the wireless connection, refer to the documentation of the router or contact the router manufacturer.
n Time ` ` ` ` The time will synchronize with the NTP(Network Time Protocol) server automatically. For this, Internet connection is required. You need to set the timezone correctly to obtain the exact time setting. The time displayed without Internet connection may not be accurate. b c 03 Monitoring Item Description Time Confirm the camera's time. b Time Zone Select your region. c Display Time Select the time format displayed in time setting.
Notification Alarm & Notification The event alarm is sent through Gmail. Camera has ability to send event notifications when motion or audio is detected. Item 24 · English Enter your Gmail address and password. 3. Click . 4. Select
Push alarm Notification Alarm Schedule The push alarm is provided through the web viewer and mobile app in which the camera is registered. Alarms will only operate for the times selected by the user. b 03 • Push alert list shows the list of IDs of users who registered cameras. When an alarm occurs, the web site will send push alerts to each smart phone. Monitoring Item Description Only Scheduled Time Alarm function will only operate for the time/day designated by the user.
n SD card ` ` Set to before removing the SD card. Otherwise, the SD card may be damaged. ` ` SD card of max 32GB is supported and a FAT32 file system is supported. When an event occurs, it is saved in an SD card. b c Item Description If you set motion/audio, video will be automatically saved in your SD card. Use the SD card b Continuous Recording Saves the video without being interrupted by events that may occur.
Event Alarm Playback You can play the video recorded in your SD card. You can check the event alarm that occurred. b c Description Delete by dates Delete all the event alarms on the date. b Delete All Delete all the event alarms for thirty days. c Display Events Displays the number of events occurred in the 30 day list. Arrange by types Arrange the event list by event types. 03 Item Description Type Set the event type to search for during the search period.
Information My Account n 28 · English ` If you want to change the member information, click on . Select the item (password, or email address) and enter your information.
Support You can download the Samsung SmartCam mobile app and user guide.
Specifications APPENDIX 04 Specifications 30 · English 30 Specifications Product Appearance 30 32 Troubleshooting 33 Specifications Item Description OS Linux Resolution 1920x1080, 1280x720, 640x480 Max. Framerate 1080p@20fps Video Compression Format H.264, MJPEG Streaming Capability Multiple Streaming (Up to 5 Profiles) Angular Field of View (D/V/H) 128°/ 62°/ 111° Low Light Performance 0.
Item Audio Detection Description Support N/A Audio Compression Format G.711, G726 Audio Communication 2-Way Audio (Optional Microphone & Speaker), Half Duplex Memory Slot microSD (FAT32), Up to 32GB Recording & Playback Event recording, Manual recording, Continuous recording, Remote playback Ethernet RJ-45 (10/100BASE-T) Wireless Wi-Fi 802.11 b/g/n (2.4G Single-band) WiFi Direct Support (Push button) Security SSL (AES 256bit) Max.
Product Appearance 90.2 32 · English 116.6 27.3 111 83.2 Φ54 102 59.
Troubleshooting If you encounter a problem with your system, see the table below to solve the problem as quickly and easily as possible. Please follow the instruction below: Problem Action I forgot my user ID/ password. - Move to “Log-in page Forgot your ID/Password?”, and enter the registered e-mail address to which we will send you the user ID and/or a new password. It can be spammed out depending on the policy of the email server.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : 1-877-349-3149 www.samsungsv.com SAMSUNG TECHWIN EUROPE LTD.
