NETWORK CONTROLLER User Manual SPC-7000
Network Controller User Manual Copyright ©2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions 1. Read these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8.
overview Please read the following recommended safety precautions carefully. yy Do not place this apparatus on an uneven surface. yy Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. yy Do not place this apparatus near conductive material. yy Do not attempt to service this apparatus yourself. yy Do not place a glass of water on the product. yy Do not install near any magnetic sources. yy Do not block any ventilation openings.
Contents Important Safety Instructions Contents Key Features What’s Included Part Names And Functions 9 9 9 10 10 10 Precautions Before Installation Assemble Jog Shuttle/Joystick Adjust LCD Screen Angle Switching the Layout of Joystick and Jog Shuttle connecting to an external device 11 13 To Connect a RS-485/422 Device Connecting to other System Controller 3 installation 11 configure settings 14 14 15 15 16 18 18 Install Getting Started Configure Menu Device Control Network System Environment
overview Key Features The SPC-7000 network controller controls network/analog cameras, DVR, and SSM program using a network. It provides a user-friendly interface with onscreen menu, touch screen and joystick. What’s Included Unpack the product package and place the product on the floor or a flat surface. Check if the following components are all included in the product package.
Part Names And Functions Name de f e e MENU MOUSE PTZ MENU LAYOUT SEQ. PRESET SEARCH GROUP TOUR FREEZE ALARM TRACE a b RECORDER SSM CAMERA RECORDER SSM MON. CON. TILE VM CAM abc def ghi jkl mno pqr stu vwx yz d Name a Joystick Up/Down/Left/Right Rotation [FOCUS N/F] + [FOCUS N/F] + b PTZ control [IRIS C/O] + [IRIS C/O] + g ESC SETUP SHIFT FAVORI. MACRO C/O AF N/F ZOOM L T.
overview Name [PTZ(MENU)] e Mode Change Changes the PTZ mode. Function Click the [PTZ (MENU)] button while in PTZ mode and the screen mode will be changed. [SHIFT] + [MENU(Mouse)] Changes the mouse mode. Click the [SHIFT] + [MENU (Mouse)] buttons while in mouse mode and the screen mode will be switched. [SHIFT] + [Mon.(Con.)] Changes the console mode. [SHIFT] + [TILE(VM)] Runs the VMD control. [SEARCH] Outputs the video of the current tile through live/search. The video will be stopped.
installation Precautions Before Installation • The product is designed for indoor use only. • A severe impact or vibration may cause a system failure. Before you install the product, read through and comply with the following instructions. ● • Keep it away from a strong magnetic field or electric interference, or wireless devices such as radio or TV set. • Do not put excessive force on it. • Keep the installation site clean and dust-free all the time while or after you have installed the product.
installation Assemble Jog Shuttle/Joystick When assembling the jog shuttle or joystick, press it until you hear a clicking sound. MENU MOUSE PTZ MENU LAYOUT SEQ. PRESET SEARCH GROUP TOUR FREEZE ALARM Switching the Layout of Joystick and Jog Shuttle For convenience you can switch the position of joystick and jog shuttle module. switch between left and right, turn off the system controller and switch the modules manually.
connecting to an external device The SPC-7000 network controller can be used by connecting to cameras, DVR, and other external devices. SSM Main Controller NETWORK SSM NETWORK SSM NETWORK Sub1 Controller Sub2 Controller You can control a PTZ camera and DVR that support RS-485/422 communication with the controller. 1. Connect the rear PORT 1 with RS-485 port of the PTZ camera or DVR. 2. According to the external device connected, select RS-485 (Half Duplex) or RS-422 (Full Duplex) connection.
connecting to an external device Connecting SRD-16XX/8XX type DVR Connecting SRD-4XX type DVR For the half duplex system (RS-485) ❖❖ For the half duplex system (RS-485) Connect between DVR and SPC-7000 using RS-485 port on the rear of the DVR. Connect the RS-485 socket on the back of SRD-4XX with SPC-7000. -- Connect the TX (+) of SRD-4XX socket to the port 1 socket TX (+) of SPC-7000. -- Connect TX (+) of RS-485 port of the DVR with TX (+) of PORT 1 of SPC-7000.
Connecting to other System Controller ● `` You can connect up to 16 controllers simultaneously. `` For communication settings of the controller, refer to “Setting the controller ID” of “Menu Setting”. (► page 17) connecting to an external device For the half duplex system (RS-485) -- Connect TX (+) of PORT 2 of SPC-7000 with TX (+) of PORT 2 of the other SPC7000. SSM Main Controller NETWORK -- Connect TX (–) of PORT 2 of SPC-7000 with TX (–) of PORT 2 of the other SPC7000.
configure settings Install 1. With the computer turned on, connect the SSM terminal of the controller to the USB port of the computer. 2. A window will open that says A new device has been detected. 3. Your computer will automatically recognize the device. `` Install the device by following the instructions provided in the installation window, if necessary. 4. When the device is recognized, the controllers installed will be displayed on the game controller list in the Windows control panel.
Configure Menu 4. Press the button and the selected camera will be registered. ● When the system settings screen appears, select your desired settings item. 3. Enter an and and press the button to access the camera. Configure Settings • Model: Shows the camera model name. • IP address : Shows the IP address of a network camera. • Status : Displays Success or error code guide information.
configure settings 3. Press the button to enter an ID, password and port number. 4. Press the button to access the camera. 5. Check the test results. 6. Press the button to complete the registration. • Adding an analog device 1. Select the check box and press the button. 2. Select as the device type. 3. Select each item to enter the ID, type, protocol, and transmission speed. `` By selecting as the type, protocol can be selected. 4.
User & Password You can change the administrator’s password and grant a device ID. 2. Click the button. 3. Select a device to assign to the user. 4. Select whether to use a password. 5. To use a password, press and set a password to use. 6. After setting a password, press the button. the password does not conform to the password policy, you will need to select a password that meets the MM `` Ifpassword requirements. 2. Press the button and the user selected will be deleted. 3.
configure settings Change Module You can switch the position between jog shuttle and joystick from left to right or vice versa. 1. Select the menu. 2. You can check that the power is turned off and switch the jog shuttle position with the joy stick by pressing the button. 3. Check the current setting, press . System Environment You can update the current firmware using the firmware files in the USB memory.
To backup the controller settings If you want to change the controller or replace the camera, you can save the settings of the controller as a file and load the controller settings into a new camera. ● 1. From the menu setup screen, press . Configure Settings 2. Press . 3. Press . The backup process begins. not disconnect the USB memory or power MM `` Do cable during the backup. Otherwise, it may fail to backup the controller settings.
control Control Cameras You can configure a camera, storage device and settings menu. MM `` If the version of SUNAPI of a network camera registered, a specific function may not work. Enter Camera Control Mode Select on the main screen. Select a Camera Using the direction keys, move to your desired camera on the list of registered cameras, and press the [ENTER] key. Using the direction keys, move to the button and press the [ENTER] key.
Group Tour `` You can designate up to 6 groups. `` A single group can contain up to 128 presets. To set a tour You can make a group of multiple presets before calling them in sequence. 2. From the group list, select an individual list and press the button to move to the settings page. 3. Press the button. 4. From the preset list, select a preset to add to the group. 5. Specify the speed and dwell time. 6. Press the button to save. To execute the group function Control 1.
control Swing You can move the camera between two preset points to monitor the course. Swing setup 1. Select the menu. 2. Select the [PRESET] button for a type to set (PAN, PAN/TILT or TILT). 3. Set a start preset and an end preset. 4. Set a speed and switch time. 5. Press the button to save. To execute the swing 1. Select the menu. 2. Press the button of a swing to execute (PAN, PAN/TILT or TILT). 3. The swing function will be executed.
Auto Tracking Control Storage Devices As functions vary depending on the device, please refer to the user manual for the device. SSM ● You can select whether to ON/OFF the auto tracking function of a camera that supports this function. Control You can control the storage devices registered in the SSM by selecting the SSM. you select the SSM, the camera will MM `` When run in SSM mode. Alarm Output You can turn the forced alarm output ON/OFF.
control PTZ control [FOCUS N/F] + Runs the Focus Near/Far motion. [FOCUS N/F] + -- [FOCUS N/F] + : Focus Near -- [FOCUS N/F] + : Focus Far [IRIS C/O] + Runs the IRIS Open/Close operation. [IRIS C/O] + -- [IRIS C/O] + : IRIS Open -- [IRIS C/O] + : IRIS Close [PRESET] When you click a number + [PRESET] button, the preset corresponding to each button number is activated. [GROUP] When you click a number + [GROUP] button, Group/Scan corresponding to each button number is activated.
Play screen control [SEARCH] Outputs the video of the current tile through live/search. Starts/Ends manual recording of the video. Shuttle wheel Fast plays in the forward direction when the wheel is turned clockwise, or fast plays in the reverse direction when the wheel is turned counter-clockwise. Jog wheel Performs frame search. 0~9 Button to input a number. [ESC(SETUP)] 2. Select , . If you select either console or VM mode, configurable sub functions will be enabled.
control Recording Change Layout Search 2. Enter the layout number to be changed. Starts or stops recording. Displays a playback video. Snapshot Saves a captured image. `` The image will be saved on the PC where the SSM is installed. Alarm OFF Turns off an event alarm. DVR You can control by connecting to DVR. 1. Select . Configurable sub functions will be enabled. `` In SRD protocol, depending on the connected DVR, only the menus that can be set are displayed on the screen.
appendix Specifications Item Compatibility Protocol (Network Camera) Protocol (analog camera) Protocol (DVR) Multilingual Support LCD Display USB Port Joystick Jog Shuttle Power Operation Temperature Operation Humidity Dimensions Weight RJ-45(Ethernet) RS-485 / 422 Max. 255 Network/analog camera, SSM, DVR SUNAPI Problem Unable to communicate with the controller. Action • Check if the RS-485 communication lines are connected normally. • Check the cable connection between SPC-7000 and the PC.
GPL/LGPL Software License The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@hanwha.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. yy GPL Software : Linux Kernel 3.0.
12.
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) I f distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.
