RFID Reader User Manual SSA-R2000V
RFID Reader User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING • To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. WARNING 1.
safety information FCC Statement Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
contents Features What’s included At a Glance Cable Color Scheme Cable Selection INSTALLATION AND EXTERNAL CONNECTION 9 10 11 Installation Precautions on installation External Connection INITIALIZATION 12 Basic Operations OUTPUT FORMAT 13 14 15 Wiegand Output RS-232 Output 8 Bit Burst Output Format TROUBLESHOOTING 16 Troubleshooting PRODUCT SPECIFICATIONS 17 Product Specifications 6 9 CONTENTS 6 6 7 8 8 PRODUCT INTRODUCTION 12 13 16 17 English _ 5
product introduction FEATURES This model is an elegant-looking proximity reader that is featured by the capacitive touch-sensing keypad. The back-lighted keypad is useful especially for night operation, and its epoxy adhesion and aluminium case relieve you of worries about the rain or any other challenging weather conditions. This model permits user access through authentication of the presented proximity card and personal identification number using the keypad.
AT A GLANCE Front/Rear PRODUCT INTRODUCTION 3 4 5 SSA-R2000V 6 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 Tamper Switch A tamper switch to detect falling from the wall. 4 Connection Cable Used to connect to the power source or I/O cable. 5 Buzzer Piezo buzzer. 6 Fixing Hole Fixing hole for wall-mounting.
product introduction CABLE COLOR SCHEME Item Cable Color Signal Line Description Red DC +12V Power (+12V) Black GND Earth-grounding for power Green WIK_DATA0 Wiegand Data 0 Output Port White WIK_DATA1 Wiegand Data 1 Output Port Purple TX_OUT ΄ͣͤͣ͑͞ΦΥΡΦΥ͑΅ΖΣΞΚΟΒΝ Orange RS-232 GND ΄ͣͤͣ͑͞ΣΠΦΟΕΚΟΘ͑΅ΖΣΞΚΟΒΝ Brown NC ͿΠΥ͑ΦΤΖΕ͟ Yellow Green LED Control ΣΖΖΟ͑ͽͶ͵͑ʹΠΟΥΣΠΝ͑ͺΟΡΦΥ͑ ΅ΖΣΞΚΟΒΝ Gray Orange LED Control ΣΒΟΘΖ͑ͽͶ͵͑ʹΠΟΥΣΠΝ͑ͺΟΡΦΥ͑ ΅ΖΣΞΚΟΒΝ Blue Buzzer Control BUZZER Contro
installation and external connection INSTALLATION 1. See [Figure 1] to drill 6-32” holes and 1/2” holes (totally 4) into the wall. 2. Tighten the four screws to secure the product to the wall. 60.30 79.60 4cm 100.80 4.35cm 6-32 or M3 Screws 8.7cm 00 91.50 Ø1. 86.50 1/2˝ hole 4.35cm Ø1. 72.50 6.4cm 12.50 50 6-32 hole 69.10 54.50 36.50 26.23 Reader Module Ø1.50 SSA-R2000V 18.50 Bezel 6.00 0.00 [Figure 1] 80.60 72.30 49.30 56.30 62.30 18.30 31.30 64.00 0.00 7.80 8.30 81.
installation and external connection PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. Metal Wall Spacer 2000V SSA-R Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back, the read range may be reduced.
EXTERNAL CONNECTION WIRING DIAGRAM CONTROLLER Green Wiegand Data 1 Out White Tamper Switch Out(NC) Light yellow Tamper Switch Out(COM) Pink Buzzer Control In Blue RS-232(TX) Purple PC RS-232(GND) Orange LED Control In(Green) Yellow LED Control In(Orange) Gray SSA-R2000V Red DC +12V Black GND POWER Category Cable Wiring Connect the DC+12V to the red line. Power Supply Unit Connect GND to the black line.
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card C ar d X Y [ Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller.
output format WIEGAND OUTPUT Timing Diagram 5V 1ms DATA-0 0V 5V DATA-1 LOGIC 1 2 3 n-2 n-1 0 1 1 1 0 0V n *n : 34 or26 0 Data Type (26-bit) • • • • Bit 1 : Even Parity (bit 2 ~ bit 13) Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) English _ 13 OUTPUT FORMAT 100us
output format RS-232 OUTPUT Output Waveform LSB +15V 0 1 MSB 0 0 0 0 0 1 0 Space(=0) +3V Indeterminate Region 0V -3V Mark(=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type M START (0X02H) DATA (8 Char) END (0x03H) LRC START(0X02H) DATA (1~8 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC : This is the result of XOR operation of each byte from Start to E
8 BIT BURST OUTPUT FORMAT 8Bit Burst Output Format Binary Hexa Keypads Binary Hexa 0 11110000 F0 6 10010110 96 1 11100001 E1 7 10000111 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 01101001 69 4 10110100 B4 ESC 01011010 5A 5 10100101 A5 ENT 01001011 4B English _ 15 OUTPUT FORMAT Keypads
troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. PROBLEM SOLUTION My card is not read properly. 1) 2) When I turn on the product, it sounds a beep with dimly turned on indicator. 1) Check the rated voltage specified in the user manual and the catalog. Ensure that the card must comply with the PSK (125KHz) format provided by Samsung. - Cards of 13.56MHz format can not be used. (Contact the card retailer regarding the card format.
product specifications PRODUCT SPECIFICATIONS Item SSA-R2000V Power / Current DC 12V / Max.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungsecurity.com www.samsungtechwin.com SAMSUNG TECHWIN EUROPE LTD.
