NETWORK CAMERA User Manual MGC-D8080LI/MGC-D8080/MGL-D8080
Network Camera User Manual Copyright ©2023 Hanwha Vision Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. ~ Do not place this apparatus on an uneven surface. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. ~ Do not place this apparatus near conductive material. ~ Do not attempt to service this apparatus yourself.
CONTENTS OVERVIEW 6 6 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/ SDXC Memory Card Specifications (MGC-D8080LI/MGC-D8080) NAS recommended specs (MGC-D8080LI/ MGC-D8080) Video output (MGC-D8080LI/MGC-D8080) Optional Accessories for Installation NETWORK CONNECTION AND SETUP 33 33 33 34 34 34 35 35 36 37 37 ONE-WAY CAMERA 9 9 10 12 What’s Included At a Glance Installation WEB VIEWER 38 LED PARKING INDICATOR LIGHT 20 20 21 22 Connecting the Camera Direc
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS (MGC-D8080LI/MGC-D8080) CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Recommended browser: Chrome Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) Supported OS : Windows, Mac, Linux, Android, iOS, Chrome Verification environment - Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later - Mac 10.13/14: Safari version 11.0.
! OVERVIEW One-way camera (including the LED parking indicator light) One-way camera LED parking indicator light MGC-D8080LI MGC-D8080 MGL-D8080 9 9 20 English _7
overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available.
One-way camera WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.
One-way camera AT A GLANCE Item Appearance a b c d a b c d 10_ One-way camera Description a Skin cover Covers the exposure of the body cover and protects the body from external shocks. b Body protection cover Waterproofs and protects the lens and camera body. c Camera body Body part where the camera lens and connection terminals are included. d Mount plate Used to fix the raceway or separately purchased mount.
Inside a b i hg f a c Item d e d e Description a PoE+ port Used to connect the PoE+ or Ethernet cable for network connection. b LED light Lights in various colors depending on the detected parking situation. c Alarm I/O / Power port (DC 12V) Connects the large port part of the audio/alarm/power cable for the connection of Alarm I/O and power. d Auto focus button It automatically performs lens adjustment for focusing while installing the camera.
One-way camera INSTALLATION J 2. Lift the skin cover as if flipping it upward for separation. ` Check the 2 fixing screws for the skin cover on the rear of the product are loosened. ` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
3. Remove the body protection cover by turning the 2 fixing screws on both sides of the body protection cover counterclockwise with the provided Torx L wrench. ` If it is difficult to separate the cover, check if the 4 fixing screws for the body protection cover are loosened. Inserting a Micro SD card Insert the micro SD card into the micro SD card slot on the camera body in the arrow direction. ` It is not required to completely remove screws from the cover.
One-way camera Removing a Micro SD card Installing on the raceway (mount plate) Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. 1. On the raceway, mark the place where the provided raceway mounting adapter is to be inserted, and then drill a hole for it. J ` Before removing the Micro SD card, in --, set the device to and press the [Apply] button and turn the camera off.
3. Place the mount plate rubber onto the upper part of the mounting adapter, and then insert it into the drilled hole. Installing on the raceway bracket or structure (mount plate) 1. Attach the installation template on the desired surface and drill holes for screws and cables. ! ONE-WAY CAMERA 2. Fix the mount plate using appropriate screws. 4. At the top of the raceway, insert the mounting adapter nut into the adapter to complete the mount plate installation. 4x ~ Not Included 5.
One-way camera Mounting the camera body [Installing the network cable] 1. Insert the camera body into the mount plate. ` Align with the hinges as shown in the figure and then insert it. 3. Remove the protruding part on the removed cable bushing. 4. Use the cap installer to route the network cable through the cable bushing. Cap Installer 5. Insert the cable bushing of the network cable into the camera body. 2. Remove the cable bushing from the camera body.
8. Connect the small terminal part of the audio/alarm/power cable to the audio cable port, and then connect the large terminal part to the alarm I/O and power (DC 12V) port. [Installing the Audio/Alarm/Power cables] 9. Lift the camera body and then fix it to the mount plate with the 2 fastening screws. ! ONE-WAY CAMERA 6. Connect the connector of the network cable to the camera’s PoE+ port. 7. Mount the cable bushing of the provided audio/alarm/power cables to the camera body. 2x TR20 10.
One-way camera Assembling the cover 1. Turn the 6 fixing screws for the body protection cover clockwise to fix the body protection cover with the provided Torx L wrench. 3. With the provided Torx L wrench, turn the 2 fastening screws for the skin cover on the rear of the product clockwise. 2x TR20 6x TR20 2. Place the skin cover all the way over the body protective cover, and then press 2 front parts of the skin cover as shown in the figure below.
Outdoor installation Adjusting the monitoring direction for the camera When you install the camera outdoors, it should be waterproofed with waterproof butyl rubber tape (which can be purchased in stores) so that water does not leak from the gap of the cable connected in the outdoor area. ! ONE-WAY CAMERA 1. Connect the power, audio I/O and LAN cables. 2.
LED parking indicator light WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.
Inside AT A GLANCE b Appearance ! LED PARKING INDICATOR LIGHT a b a c c Item d Item Description a PoE port Used to connect the PoE or Ethernet cable for network connection. b LED light Lights in various colors depending on the detected parking situation. c Power port (DC 12V) Used to connect the power terminal block. Description a Skin cover Covers the exposure of the body cover and protects the body from external shocks.
LED parking indicator light INSTALLATION J 2. Lift the skin cover as if flipping it upward for separation. ` Check the 2 fixing screws for the skin cover on the rear of the product are loosened. ` This product is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
3. Remove the body protection cover by turning the 2 fixing screws on both sides of the body protection cover counterclockwise with the provided Torx L wrench. ` If it is difficult to separate the cover, check if the 4 fixing screws for the body protection cover are loosened. ` It is not required to completely remove screws from the cover. Installing on the raceway (mount plate) 1. On the raceway, mark the place where the provided raceway mounting adapter is to be inserted, and then drill a hole for it.
LED parking indicator light 3. Place the mount plate rubber onto the upper part of the mounting adapter, and then insert it into the drilled hole. Installing on the raceway bracket or structure (mount plate) 1. Attach the installation template on the desired surface and drill holes for screws and cables. 2. Fix the mount plate using appropriate screws. 4. At the top of the raceway, insert the mounting adapter nut into the adapter to complete the mount plate installation. 4x ~ Not Included 5.
Assembling the parking indicator light module [Installing the network cable] 1. Insert the parking indicator light module into the mount plate. ` Align with the hinges as shown in the figure and then insert it. 2. Remove the cable busing from the parking indicator light module. ! LED PARKING INDICATOR LIGHT 3. Remove the protruding part on the removed cable bushing. 4. Use the cap installer to route the network cable through the cable bushing.
LED parking indicator light 5. Insert the cable bushing of the network cable into the parking indicator light module. [Installing the power cable (for use of DC power)] 7. Remove the cable bushing on the power port (DC 12 V) from the parking indicator light module. 6. Connect the connector of the network cable to the PoE port of the parking indicator light module. 8. Remove the protruding part on the removed cable bushing. 9.
10. Insert the cable bushing of the power cable into the camera body. 12. Lift the parking indicator light module and then fix it to the mount plate with the 2 fastening screws. TR20 11. Connect the power terminal block to the power port (DC 12V).
LED parking indicator light Assembling the cover 1. Turn the 6 fixing screws for the body protection cover clockwise to fix the body protection cover with the provided Torx L wrench. 3. With the provided Torx L wrench, turn the 2 fastening screws for the skin cover on the rear of the product clockwise. 2x TR20 6x TR20 Outdoor installation 2. Place the skin cover all the way over the body protective cover, and then press 2 front parts of the skin cover as shown in the figure below.
installation & connection CONNECTING WITH OTHER DEVICE J WiFi dongle ` The Test Monitor Out port of the product is provided for easier installation, and is not recommended for monitoring purposes. (MGC-D8080LI/MGC-D8080) ` The Micro USB port of the product is provided for easier installation, and is not recommended for monitoring purposes. ! INSTALLATION & CONNECTION (MGC-D8080LI/MGC-D8080) Ethernet Connection Connect the Ethernet cable to the local network or to the Internet.
installation & connection Power Supply Connecting WiFi Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. Camera Setup J ` If the power sources for PoE+ and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE+ and DC 12 V. 2. Select the camera SSID after turning on the WiFi. The MGL-D8080 model can use the PoE power. 3. Run the Wisenet Installation application.
Connecting to Audio Input/Output (MGC-D8080LI/MGC-D8080) J ` In the case you access the web viewer and select an external microphone as the audio input sources in
installation & connection Connecting to the I/O port box (MGC-D8080LI/MGC-D8080) To connect to an external sensor Connect the Alarm I/O cable to the corresponding port of the port box. To use as an Alarm IN: Connect one of the [ALARM I/O] port and the other terminal to the [GND] port.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. Camera External Remote PC DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera. 2.
network connection and setup USING DEVICE MANAGER M ` Device manager program can be downloaded from - menu at Hanwha Vision website (https://www.HanwhaVision.com). ` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.
Configuring Dynamic IP Receive IP address from DHCP ~ Example of the Dynamic IP environment - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server - If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 1. Click the camera from the list that you want to automatically configure the IP. MGC-D8080LI 2. Click < + > at the main page of device manager. ~ Equipment Setting menu appears.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. ~ A user can change each port using the camera setting screen.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. M ! NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. ` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 ; http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 ; http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. ` For a new password with 8 to 9 characters, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 characters or longer, you must use at least 2 types of those mentioned. (support up to 64 characters) 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3.
appendix TROUBLESHOOTING PROBLEM SOLUTION When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. (MGC-D8080LI/MGC-D8080) ~ This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
