2.4GHz Digital Wireless Conference System Ver 2.
Installer Compliance Responsibility 1. This device requires controlled installation by professional installers, and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. 2. Since our device can be paired with a variety of antennas and cables, the specific Antenna, Cable, and Output Power fields are provided to the professional installer to meet regulatory requirements. 3.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.
2.
2.
2.
2.
2.
2.4GHz Digital Wireless Conference System ※ Safety Instructions 1. Only a certified service technician should perform repairs on this equipment. 2. In case of maintenance, examination or repair, please contact the store you purchased or our customer service team. 3. Never touch the equipment or appliance with wet hands. 4. protect the equipment from liquids and foreign substances. 5. To prevent fire or shock hazard, do not expose your equipments to rain or moisture. 6.
2.
2.4GHz Digital Wireless Conference System basic setup methodㅣ 10 ● basic setup method I - Using main controller, connecting general conference system - setting procedure 1. Place Main controller KMC-200 to proper plane location ( ; Install to Rack Cabinet) 2. Connect power adaptor cable to power port in rear side 3. Connect external audio device to Audio Out terminal in rear side (external speaker output) 4. Connect Antenna to ANT terminal in rear side 5.
system connectionㅣ 11 2.4GHz Digital Wireless Conference System system connection (basic conference system) 2.4GHz unique coaxial cable (L-5DFB) Max.
system system connectionㅣ 12 2.4GHz Digital Wireless Conference System system connection (video conference system and PC-OS) 2.4GHz unique coaxial cable (L-5DFB) Max.
2.4GHz Digital Wireless Conference System ● basic setup method II - Without Main controller, wiring conference system simply using Stand unit only (Stand Alone Mode) - setting procedure 1. Place Stand unit to conference location (embed folding-Mike and battery-pack) 2. Setting Chairman Stand unit to MASTER 3. Power on each Stand unit pressing front-TALK-button by 2~3 seconds 4. Check synchronization between MASTER stand unit and member stand unit (Antenna icon appears in the LCD of Stand unit) 5.
system connectionㅣ 14 2.
2.
antenna connectionㅣ 16 2.
antenna installationㅣ 17 2.
Main Controller (KMC-200)
Blank page
Product detailsㅣ 20 2.4GHz Digital Wireless Conference System Product details ● Main controller KMC-200 1 2 3 4 5 6 7 8 9 10 11 1. power ON/OFF button 5. ANT connector 9. AUX input terminal 2. LCD screen 6. RS-232 port (PGM) 10. Ethernet port (PC) 3. setting menu/selection button 7. RS-232 port (CAMERA) 11. FUSE (1A) 4. 3.5mm Headphone output terminal 8. audio output terminal 12.
system startㅣ 21 2.4GHz Digital Wireless Conference System system start symbol 2.4GHz Digital Conference System Loading . . Ver System Rx On Audio LV : booting screen when power ON symbol 2.
2.
Stand Unit (KSM-200C / KSM-200D)
Blank page
Product detailsㅣ 33 2.4GHz Digital Wireless Conference System Product details ● Stand unit KSM-200 (each Chairman / Member) 4 2 5 3 1 1. TALK ON/OFF button 6 2. LCD screen 6. Headphone connectiontermi nal (3.5mm) 3. menu setting button 7. charging battery 4. Microphone connection terminal 5.
system start ㅣ 34 2.
2.
2.
2.
Specification ㅣ 59 2.4GHz Digital Wireless Conference System Specification Main controller KMC-200 general characteristic symbol device type details symbol 2.
Specification ㅣ 60 2.4GHz Digital Wireless Conference System Specification Main controller KMC-200 electrical characteristic details symbol details frequency band 2.4GHz ISM BAND Sampling rate 24 kHz Mono frequency stability ±20ppm Headphone output 0.5 W audio output -15 ~ +5 dB frequency modulation FSK data speed 2Mbps audio input -20 ~ -5 dB RF output < 100 mW wight 2.1 kg Impedance 50 Ω size 484 x 204 x 45 (mm) Sensitivity -87 dB Input powe 0.
Specification ㅣ 61 2.4GHz Digital Wireless Conference System Specification Stand unit KSM-200 general characteristic symbol details device type Microphone attached, for desktop installation type Indication method LCD Type device type device setting operation quantity Setup Mode setting Max 255 EA per system DC 3.
Specification ㅣ 62 2.4GHz Digital Wireless Conference System Specification Stand unit KSM-200 electrical characteristic symbol details symbol details frequency band 2.4GHz ISM BAND Sampling rate 24 kHz Mono frequency stability ±20ppm speaker output 0.5 W frequency modulation FSK color Dark Grey data speed 2Mbps weight 575 g RF impedance 50 Ω size 236 x 138 x 61 (mm) receiving sensitivity -87 dB input power DC 3.
Specification ㅣ 63 2.4GHz Digital Wireless Conference System Specification Microphone KVM-480D electrical characteristic symbol details symbol details Mike type Electret rated voltage 1.5V Mike pattern Uni-directional max voltage 10V sensitivity -45dB+/-2dB (1kHz, 0dB=1V/Pa) folder color Dark Grey 50Hz ~ 20kHz Ring color RED frequency response S/N >66dB max input level 120dB SPL impedance 1.0kΩ rated current Max.0.
Specification ㅣ 64 2.
