Owner's Manual

M100-BT / M200-BT OWNER’S MANUAL
11
M200-BT: FEATURES AND FUNCTIONS
1
CHANNEL 1, 2, 3, 4 INPUT JACKS
Connect XLR or 1/4-inch cables
2
MIC/LINE SWITCHES
Set these to match the type of source connected to the input above them
- Mic: for microphones, or line level sources with low output volumes
- Line: for line level sources
3
MIC/GUITAR/LINE SWITCHES
Set these to match the type of source connected to the input above them
- Mic: for microphones, or line level sources with low output volumes
- Guitar: for acoustic guitar or guitar pedal board
- Line: for line level sources
4
ECHO KNOBS
Set the amount of echo effect
5
BASS AND TREBLE KNOBS
Adjust the sound of the channel
6
CHANNEL LEVEL KNOBS
These knobs set the volume for the channels
7
PEAK LIGHTS
If one of these illuminates, turn down the knob next to it to avoid distortion
due to excessive level.
Note that all inputs on Channel 3-4 STEREO, including Bluetooth, can be
used simultaneously
8
BALANCED LINE INPUTS
Balanced or unbalanced line level sources can be connected here
9
AUX INPUT
Audio from smartphones, computers and other consumer audio devices
can be connected here
10
BLUETOOTH AUDIO INPUT
Bluetooth audio input is automatically enabled each time you turn the
mixer on, will automatically reconnect to the previous Bluetooth audio
source if it is available, and will otherwise be available for Bluetooth
pairing from a source audio device such as a smartphone.
- To pair, look for M200-BT from your Bluetooth audio
source device.
- LED is lit solid when currently paired, blinking when available for
pairing, and off if Bluetooth has been disabled by a press of the
Bluetooth Off button.
- On/Pair button forces any currently connected Bluetooth audio source
to disconnect, and makes the mixer available for pairing.
- Off button disables Bluetooth. (Bluetooth will be re-enabled next time
you turn power off and on, or if you press the On/Pair button.)
11
STEREO OUT
The combined audio from all channels is output from the STEREO OUT.
12
SPEAKER MODE
When this button is up, speakers operate in stereo, with Master Level knob
(16) setting the level.
When this button is down, Speaker 1 operates as your Master speaker,
while Speaker 2 operates as your monitor speaker, with level controlled
by Monitor Level (15) knob.
Note that in Master+Monitor mode, the Monitor speaker will be tuned
for reduced low frequencies, to minimize rumble and potential for
microphone feedback
13
LEVEL/CLIP METER
Upper meter shows level of speaker 1, lower meter shows level of speaker
2. When speakers are operating in stereo, upper meter shows left level
and lower meter shows right level. When speakers are operating in
Master + Monitor mode, upper meter shows Master level and lower meter
shows Monitor level.
If CLIP lights are lit red continuously or frequently active, turn down the
MASTER LEVEL (16) or MONITOR LEVEL (15) knobs
14
GRAPHIC EQ
Adjusts the overall sound of both speakers, including the Master and
Monitor speakers in Master + Monitor speaker mode.
15
MONITOR LEVEL
This knob operates only when Speaker Mode (12) button is pushed in,
setting the level of speaker 2.
16
MASTER LEVEL
When Speaker Mode (12) button is pushed out, this knob sets the level for
both speakers. When Speaker Mode (12) button is pushed in, this knob
sets the level of Speaker 1 only.
17
TO SPEAKERS
Connect one end of each included speaker cable to one of these jacks.
Connect the other end of each speaker cable to one of the speakers’ rear
panel jacks. Both speakers are identical, you can connect either speaker
to either jack.
18
Connect power cable here.
If the mixer will not power on and you suspect its fuse may have blown,
turn off the power switch, and open the fuse compartment using a small
flat blade screwdriver. If metal strip in fuse is broken, replace with T3.15AL
250V fuse.
19
Switches the power on and off