ITEM #0803775, 0721899, 0807427 PAWTUCKET CEILING FAN MODEL #40958, 40959, 40305 Español p. 20 Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. ATTACH YOUR RECEIPT HERE Serial Number _________________________ Purchase Date _________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information. . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS D B G H E C F A L K P PART A B C D E F N M Q R S T I U DESCRIPTION Motor Housing Upper Mounting Bracket Receiver (preassembled to Upper Mounting Bracket [B]) Lower Mounting Bracket (preassembled to Motor [E]) Motor Switch Housing (preassembled to Motor [E]) J O V W QUANTITY 1 1 1 1 1 1 G Switch Housing Cap (preassembled to Light Kit [H]) 1 H I J K L M N O P Q R S T U V W Light Kit Finial Cap (preassembled to Light Kit [H]) Finial (preassembled to Light Kit [H]) Gla
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Qty. 2 Blade Screw Qty. 15 + 1 extra CC EE Blade Washer Qty. 15 + 1 extra 4 Plug Button Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
SAFETY INFORMATION CAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are secured. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
INITIAL INSTALLATION 1. Turn off the circuit breakers and the wall switch to the fan supply line leads. 1 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Ensure the blades (M) will be at least 30 in. from any obstructions and will be at least 7 ft. above the floor. 2 30 in. Min M 7 ft. Min 3. Secure the upper mounting bracket (B) to the outlet box (not included) using screws and washers provided with the outlet box.
INITIAL INSTALLATION WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.
INITIAL INSTALLATION 7. Remove the mounting bracket screws (R) and spring washers (W) from underneath the lower mounting bracket (D). Also remove the motor screws (V) from the bottom of the motor (E). Retain for later use. 7 Note: Make sure to keep loose hardware separate to avoid confusion during installation. D R W E V 8. Place one tab of the lower mounting bracket (D) into a slot in the upper mounting bracket (B).
FAN WIRING WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. 1.
FINAL INSTALLATION 1. Temporarily lift the motor housing (A) to the upper mounting bracket (B) to determine which two motor housing screws (T) in the sides of the upper mounting bracket (B) align with the slotted holes in the top edge of the motor housing (A). Partially loosen the two motor housing screws (T) that align with the slotted holes. Remove the other two motor housing screws (T) from the upper mounting bracket (B). 1 B T Slotted Hole A 2.
FINAL INSTALLATION 4. Install the blade arm (L) to the underside of the motor (E) with motor screws (V) previously removed (Step 7, page 9). Tighten with Phillips screwdriver. 4 Repeat for each blade arm (L). E V Note If you wish to install the fan without the light kit, proceed to Step 10. L 5 5. To install the light kit, first remove the switch housing screws (S) preassembled to the switch housing cap (G).
FINAL INSTALLATION 7. Install bulbs (N) into the sockets on the light kit (H). Important Make sure you allow the bulbs (N) and light kit (H) to cool before you replace the bulbs. 7 H N 8. Remove the preassembled large washer (P), hex nut (Q), finial cap (I) and finial (J) from the light kit (H). 8 H P Q I J 9. Lift the glass shade (K) onto the threaded rod at the bottom of the light kit (H). Re-install large washer (P) and secure with hex nut (Q).
FINAL INSTALLATION 10. To install the fan without the light kit (H), remove the hex nut and lock washer from the rod on the inside of the switch housing cap (G). Remove light kit (H) from the switch housing cap (G) and discard, then install the plug button (EE) into the center hole of the switch housing cap (G). 10 Hex Nut Lock Washer G H G EE 11. Remove the three switch housing screws (S) from the switch housing cap (G) and install the switch housing cap (G) onto the switch housing (F).
OPERATING INSTRUCTIONS 1. Remove the battery cover from the back of the remote found in remote pack (O). Insert the battery from remote pack (O) into the remote; ensure polarity of battery matches the polarity indicated in the battery compartment -- positive (+) to positive (+) and negative (-) to negative (-). Replace the battery cover and press the fan power button on the remote to ensure the LED indicator illuminates and the remote turns on the fan.
CARE AND MAINTENANCE At least twice each year, tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Bulb Replacement: Use 60-watt max. E26-base LED, CFL or incandescent bulbs. Halogen bulbs are not recommended for this item. Battery Replacement for Remote: Use A23 12-volt battery. Important Shut off the main power supply before you begin any maintenance tasks. Do not use water or a damp cloth to clean the ceiling fan.
TROUBLESHOOTING PROBLEM The fan is noisy. Remote doesn’t work. POSSIBLE CAUSE 1. The blades are loose. CORRECTIVE ACTION 1. Check and tighten all screws that hold the fan blades to the blade arms and the motor. 2. There is a cracked blade. 2. Replace the cracked blade. 3. The outlet box is not secure. 3. Ensure the outlet box is secured to the building structure. 4. The mounting bracket is not secure. 4. Ensure the mounting bracket is secured to the outlet box and that the screws are tight. 1.
LIFETIME LIMITED WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, excluding any glass or plastic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
