ITEM #0883784, 0883785 CARATUK RIVER CEILING FAN MODEL #41362, 41363 Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. Español p. 21 ATTACH YOUR RECEIPT HERE Purchase Date _________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparation . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS P E A S T D B C F R G Q I H O J N L K M PART A B C D E F G H I J K L M N O P Q R S T DESCRIPTION QUANTITY Downrod 1 Downrod Pin (preassembled to the Downrod [A]) 1 Downrod Clip (preassembled to the Downrod [A]) 1 Canopy 1 Mounting Bracket (preassembled to the Canopy [D]) 1 Canopy Cover (preassembled to the Canopy [D]) 1 Motor Assembly 1 Switch Housing (preassembled to the Motor Assembly [G]) 1 Light Kit 1 Glass Globe 1 Bulb 1 Blade Arm 5 Blade 5 Yoke Cover 1 Motor Screw (pr
HARDWARE CONTENTS (shown actual size) CC Blade Screw Qty. 15 + 1 extra Blade Washer Qty. 15 + 1 extra 4 b o r Br e e ar H H ar Wire Connector Qty. 3 + 1 extra XX DD ze BB ze AA b o r Br e e Pull Chain Extension Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
SAFETY INFORMATION CAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are secured. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
INITIAL INSTALLATION 1. Turn off the circuit breakers and the wall switch to the fan supply line leads. 1 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Determine the mounting method to use. Standard mounting is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). 2 Angle mounting is best suited for angled or vaulted ceilings.
INITIAL INSTALLATION 4. Loosen all four preassembled mounting bracket screws (Q), then completely remove the two mounting bracket screws (Q) from the round holes of canopy (D). Set aside for later use. 4 E Detach mounting bracket (E) from canopy (D). Q D 5. Attach mounting bracket (E) to outlet box (not included) using screws and washers provided with the outlet box.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 1. Remove the downrod clip (C) and downrod pin (B) from the downrod (A). Then partially loosen the set screws (S) in the yoke at the top of the motor assembly (G). 1 A B C Yoke S G 2. Insert the downrod (A) through the canopy (D) and yoke cover (N). Feed the wires from the motor assembly (G) through the downrod (A). 2 D N A G 3.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 4. Depending on the length of downrod you use, you may need to cut the lead wires back to simplify the wiring. If you decide to cut back the lead wires, it is suggested you do so in the following manner: Take the lead wires and make sure you have pulled them all the way through the top of the downrod. Measure 8 inches of lead wire, then cut the excess wire off with wire cutters (not included). 5. If you decided to cut back the lead wire in Step 4, strip 1/2 in.
CLOSEMOUNT INSTRUCTIONS Helpful Hint: The downrod (A), canopy cover (F) and yoke cover (N) are not used in this type of installation. 1 1. Remove the canopy cover (F) from the bottom of the canopy (D). D F 2. Remove three Phillips-head closemount screws (P) from the top of the motor assembly (G). Align the canopy (D) with the holes in the top of the motor assembly (G), then re-install the Phillips-head closemount screws (P) to secure the canopy (D) to the top of the motor assembly (G). 2 P D G 3.
WIRING WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a Ground (Green or Bare) wire is present. 1.
FINAL INSTALLATION Note Closemount installation will not use the downrod (A), yoke cover (N) or canopy cover (F). 1. Align the canopy (D) over the loose mounting bracket screws (Q) preassembled on mounting bracket (E). Place the keyholes of the canopy (D) onto the mounting bracket screws (Q) and rotate the canopy (D) clockwise. 1 Q E D 2. Secure the canopy (D) with the mounting bracket screws (Q) previously removed (Step 4, page 8). Tighten all mounting bracket screws (Q) securely.
FINAL INSTALLATION 3. Partially insert the blade screws (BB) along with the blade washers (CC) through the blade (M) and into the blade arm (L). Tighten each blade screw (BB) with a Phillips screwdriver (not included), starting with the one in the middle. 3 BB CC Repeat this step for the remaining blades (M) and blade arms (L). Hardware Used BB M Blade Screw x 15 L CC Blade Washer x 15 4.
FINAL INSTALLATION 6. Install the bulb (K) into the socket of the light kit (I). Then loosen the three thumbscrews (R) on the lower edge of the light kit (I). Lift glass globe (J) to light kit (I), secure by tightening the loosened thumbscrews (R). 6 R I K J 7. Attach the pull chain extensions (DD) or custom pull chain extensions (not included) to the fan and light pull chains (if applicable).
OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. 1 ar ze H H ar b o r Br e e b o r Br e e Fan Pull Chain Light Pull Chain 2. Use the fan reverse switch, located on the switch housing (H), to optimize your fan for seasonal performance. ze The light pull chain has two positions to control the light, ON and OFF.
CARE AND MAINTENANCE At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. Bulb Replacement: Use 60-watt max. E26-base LED, CFL or incandescent bulbs. Halogen bulbs are not recommended for this item. Important Shut off the main power supply before you begin any maintenance task.
TROUBLESHOOTING PROBLEM There is excessive wobbling. POSSIBLE CAUSE 1. The blades and/or blade are loose. 2. The blades are unbalanced. 2. Switch one blade with a blade from the opposite side. Or balance the fan using a blade balancing kit (sold separately). 3. The fan mounting is not secure. 3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the electrical outlet box. The bracket must be flush without movement against the outlet box.
LIMITED LIFETIME WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, excluding any glass or plastic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
