Table of contents SAFETy Safety ......................................................... 2 Specifications ............................................. 5 Setup .......................................................... 5 Operation .................................................... 7 Maintenance .............................................. 10 Parts List and Diagram .............................. 11 Warranty ....................................................
12. DON’T OVERREACH. Keep proper footing and balance at all times. 13. MAINTAIN TOOLS WITH CARE. Keep tools clean for best and safest performance. Follow instructions for lubricating and changing accessories. 14. DISCONNECT TOOLS before servicing; when changing accessories, such as belts. 15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in. 17. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the belt is unintentionally contacted.
Sander Safety Warnings For your Own Safety Read Instruction Manual Before Operating Sander 1. Wear eye protection. SAFETy 2. Support workpiece with miter gauge, backstop, or worktable. 3. Maintain 1/16 inch maximum clearance between table and sanding belt or disc. 4. The backstop is a fence near the surface that helps the operator maintain control of the workpiece and prevents the workpiece from being pulled into the machine. For safety, it must be adjusted very close to the sanding surface. SETUp 5.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Use tools with the lowest vibration when there is a choice between different processes. 4. Include vibration-free periods each day of work. 5. Grip workpiece as lightly as possible (while still keeping safe control of it). Let the tool do the work. SAFETy disorders, diabetes, or Raynaud’s Disease should not use this tool.
Assembly SAFETy TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 5. Replace the Side Cover (1) and secure it using the Guard Knob (2).
Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy Tool Set Up TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO pREVENT SERIOUS INJURy: DO NOT OpERATE WITH ANy GUARD DISABLED, DAMAGED, OR REMOVED.
Adjustment of Belt Support 1. Remove the Table (34) by removing the Bolt (8) and Locking Handle (18.2), as shown. Bolt (8) SAFETy Bolts (14) 2. Loosen the Bolts (14) on the Belt Support (16). 3. Adjust the Belt Support to no farther than 1/16″ from the back of the Sanding Belt. Belt Support (16) Table (34) 4. Tighten the two Cap Screws on the Belt Support. 5. Replace the Table and tighten it in place. Locking Handle (18.
1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working. 3. There must not be objects, such as utility lines, nearby that will present a hazard while working.
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETy TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO pREVENT SERIOUS INJURy FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 2 1 2 1 1 1 1 1 1 2 Bolt Spring Washer Bolt Axle Seat Spring Pin Spring Tracking Knob Spring Washer Lock E-Ring Motor Assembly Motor Motor Cover Switch Cover Screw Washer Screw Screw Washer Power Cord Bushing Set Screw Table Cushion Base Assembly Rubber Feet Base Spring Washer Bolt 12 32.2 22 5 32.1 3 20 10 9 17 8 1 36.1 6 36 23 30 31 24 32 21 14 19 15 16 11 36.2 4.2 29 13 4 4.1 6 4 4 1 1 1 1 1 1 1 1 4 1 2 2 26 25 32.4 32.10 32.
pLEASE READ THE FOLLOWING cAREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
