Specifications 69472 4 Tons (8,000 lb.) Max. Height 15" 69475 8 Tons (16,000 lb.) 15-5/8" 8" 4-3/4" x 4-1/2" 10.5 lb. 69481 12 Tons (24,000 lb.) 12-3/4" 6-3/4" 5-3/8" x 5-1/4" 12.5 lb. 69476 12 Tons (24,000 lb.) 16-1/4" 8-1/4" 5-3/8" x 5-1/4" 14.2 lb. 69483 20 Tons (40,000 lb.) 14" 7-1/4" 6-1/2" x 6" 18.3 lb. 69478 20 Tons (40,000 lb.) 18-3/4" 9-1/2" 6-1/2" x 6" 21.6 lb. 69484 30 Tons (60,000 lb.) 18-1/2" 11-1/4" 7-1/4" x 5-3/4" 43 lb. ITEM Weight Capacity Min.
6. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. 7. Keep clear of load while lifting and lowering. 8. Lower load slowly. 9. Do not use for aircraft purposes. 10. Apply parking brake and chock tires before lifting vehicle. 11. Lift vehicle only at manufacturerrecommended locations. 12. Inspect before every use; do not use if parts loose or damaged. 13. Keep your work area clean and well lit. Cluttered work areas invite accidents. 14.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Bleeding Saddle Oil Fill Hole Valve Release Screw Oil Filler Plug IMPORTANT! Before first use, check for proper hydraulic oil level in the Jack. Then thoroughly test the Jack for proper operation prior to its actual use.
Lifting Elevating Screw (some models) manufacturer’s owner’s manual for location of seam lifting point when lifting only one wheel and frame lifting points when lifting the entire front or rear end of the vehicle.) Plunger/ Fulcrum 3. Note: The Jack should be positioned at 90° to the vehicle’s lifting point to ensure the Jack’s Saddle and vehicle lifting point are in alignment. If not, remove and reposition the Jack before lifting the vehicle.
Lowering Plunger/ Fulcrum Handle (on Valve Release Screw) Page 6 1. Remove all tools, parts, etc. from under the vehicle. 2. Position the Saddle under the lifting point. Turn the Handle firmly clockwise to close the Valve Release Screw, and pump the Upper/Lower Handle to raise the vehicle slightly above the saddle(s) of the jack stands. Then, collapse and remove jack stand(s). 3. Slowly turn the Handle counterclockwise (never more than two full turns) to lower the vehicle onto the ground. 4.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. Before each use, inspect the general condition of the Jack.
Troubleshooting TO PREVENT SERIOUS INJURY: Use caution when troubleshooting a malfunctioning jack. Stay well clear of the supported load. Completely resolve all problems before use. If the solutions presented in the Troubleshooting guide do not solve the problem, have a qualified technician inspect and repair the jack before use. After the jack is repaired: Test it carefully without a load by raising it and lowering it fully, checking for proper operation, BEFORE RETURNING THE JACK TO OPERATION.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
–Parts Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Page 10 List Description Adjustable Saddle Saddle Socket Piston Rod Nut O-Ring (Nut) Seal Piston Bowl Washer O-Ring (Piston) Cylinder Reservoir Reservoir Seal Base Plate Washer Filter Screen Oil Fill Plug Release Valve Release Valve Seal Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Part 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Description Ball 6mm Ball Stopper Base Bolt Washer (Pump) Pump O-Ring (Plunger) Back Ring Plunger R-Pin Pin Short Pin Lin
–Assembly ASSEMBLY Diagram DIAGRAM Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Bottle Jacks For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.