WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Personal Safety 1. Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations. 2. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for a minimum of 10 minutes and get medical attention immediately. 3. Stay alert. Watch what you are doing and use common sense when operating the Sprayer.
Specifications Pump 12VDC / 2A Diaphragm Maximum Spray Output 1 GPM, 40 PSI Tank Capacity 15 gallons Weight 160 lb (with full tank) Mounting Hardware 4x Ø5/16" x 1/2" bolts and Ø5/16" washers (not included) Components and Controls Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
Assembly and Installation Instructions Read the entire Important Safety Information section at the beginning of this document including all text under subheadings therein before set up or use of this product. Assembly 1. Attach Wand Clips with Screws (14). 4. Push Washer (17) into Drain Cap. Screws 5. Push large ring of Drain Cap Tether (16) over drain tube as far as it will go. Wand Clips 6. Thread Drain Cap onto drain tube. 7. Push small ring of Tether over nub on Drain Cap.
Installation WARNING! Refer to mounting vehicle’s owner’s manual for vehicle load rating and safety instructions regarding driving while carrying a load. Ratchet Strap Locations 1. Before filling with liquid, mount the Sprayer to the vehicle’s rack, making sure that the Battery Clamps can reach the 12VDC source. 2. Attach Tank Bottom Mounts to rack with mounting hardware (sold separately) from Specifications chart. 3. Then, secure with two 1" wide ratchet straps (sold separately).
Operating Instructions Read the entire Important Safety Information section at the beginning of this document including all text under subheadings therein before set up or use of this product. WARNING! Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations. 6. Disengage the Trigger Safety Lock by collapsing it into the Trigger. Its purpose is to prevent the Trigger from being depressed accidentally.
Inspection, Maintenance, and Cleaning Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Disconnect Battery Clamps before performing any procedure in this section. Do not use damaged equipment. If abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use. Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations. 1.
Troubleshooting Problem Possible Causes 1. 2. 3. 4. Unit does not spray Power not connected. Internal Hose (8) detached. Not enough liquid in tank. Spray fluid contains particles or sand. 5. Nozzle and/or Inlet Filter clogged with mineral buildup. Spray pattern is uneven 1. Nozzle needs adjustment. 2. Spray fluid contains particles or sand. 3. Nozzle and/or Inlet Filter clogged with mineral buildup. Likely Solutions 1. 2. 3. 4. Connect power. Reattach Hose. Add liquid to tank.
Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this document as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
Assembly Diagram 9 9 9 9 1 6 12 11 2 5 5 13 10 11 8 14 7 14 15 15 3 18 Item 61263 17 16 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.