Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. REV 14g Visit our website at: http://www.harborfreight.
Table of Contents Safety Safetye��������������������������������������������������������� 2 Maintenancei���������������������������������������������� 15 Specifications.............................................. 7 Setup........................................................... 9 Operationa��������������������������������������������������� 12 Parts List and Diagram............................... 18 Warranty.....................................................
IMPORTANT SAFETY INSTRUCTIONS Safety INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING – When using tools, basic precautions should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work Area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons. c.
Tool Use and Care Safety a. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and can lead to loss of control. b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed. c. Do not use the tool if the Trigger does not turn the tool on or off.
Specific Safety Instructions 3. Choice of triggering method is important. Check manual for triggering options. Safety 20. Do not fire fasteners into a workpiece that has people, utility lines, or other objects behind or inside it. 5. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 21. Keep balance while using this tool. Keep area below clear if working in an elevated location, and secure air hose to prevent falls from bystanders accidentally pulling on it. 6.
Vibration Precautions Safety This tool vibrates during use. Repeated or long‑term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use.
Functional Description Maximum Air Pressure 100 PSI Air Inlet 1/4" – 18 NPT Air Consumption 1 CFM @ 90 PSI Safety Mechanism Type Single Sequential Nail Size Range Staple Size Range 1-1/4" to 2-1/2" 16-gauge Finish Nails 5/8" to 2" 18-gauge Brad Nails 5/8" to 1-1/2" 18-gauge 1/4" Crown Staples 100 Fasteners Maintenance Operation Setup Magazine Capacity Safety Specifications Item 61809 For technical questions, please call 1-888-866-5797.
Components and Controls Safety Air Deflector Air Inlet Plug Trigger Setup Quick Release Latch Depth Adjustment Knob Magazine Latch Operation Safety Nosepiece Safety Nosepiece – Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Maintenance Page 8 For technical questions, please call 1-888-866-5797.
Initial Tool Set Up/Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Air Supply TO PREVENT EXPLOSION: Use only clean, dry, regulated, compressed air to power this tool.
Description Non-lubricated Tools A Air Hose Filter Regulator Lubricator (optional) Coupler and Plug Leader Hose (optional) Air Cleaner / Dryer (optional) Air Adjusting Valve (optional) Maintenance A B C D E F G H Operation Lubricated Tools Setup B B C C A Function A E E F H Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapo
Item 61809 For technical questions, please call 1-888-866-5797.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Workpiece and Work Area Set Up 1. Designate a work area that is clean and well‑lit. The work area must not allow access by children or pets to prevent distraction and injury. 2.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the Trigger. • Detach the air supply. • Attempt to fire the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners. Note: This Nailer/Stapler can drive 16 Gauge Finish Nails, 18 Gauge Brad Nails and Staples.
General Operating Instructions Safety 1. Before each use, test the tool as directed in ″Single Sequential Safety Trip Mechanism Testing Procedure″ on page 12. 5. To change the depth setting of the Nailer/ Stapler, turn the Depth Adjustment Knob to the desired setting. 2. If an automatic oiler is not used, add a few drops of pneumatic tool oil to the airline connection before use. Add a few drops more after each hour of continual use. 6.
User-Maintenance Instructions TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise, vibration, or leaking air is detected, have the problem corrected before further use. TO PREVENT EXPLOSION: Lubricate only with specified lubricants. Lubricate the air inlet using only pneumatic tool oil. Lubricate the internal mechanism using only white lithium grease. Other lubricants may damage the mechanism and may be highly flammable, causing an explosion.
Clearing Jams Safety TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams): • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the Trigger. • Detach the air supply. • Attempt to fire the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners.
Troubleshooting 5. Have qualified technician clean and lubricate mechanism. Install in-line filter in air supply as stated in Initial Set Up: Air Supply on page 9. Fasteners drive too deeply. 1. Incorrect tool depth setting. 2. Too much air pressure. 1. Adjust depth setting, if available. 2. Reduce air supply pressure (PSI). Tool cycles without firing fastener. 1. Jammed fastener. 1. Clear jammed fastener according to Clearing Jams instructions on page 16. 2. Reload with correct fasteners. 3.
Parts List and Diagram Parts List Safety Part Setup Operation Maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Description Hex Bolt Bolt Sleeve O-Ring Air Deflector Hex Bolt Cylinder Cap Gasket O-Ring O-Ring Seal Seat Spring Head Valve O-Ring O-Ring Collar O-Ring O-Ring Piston Driver Blade O-Ring Cylinder O-Ring Bumper Cylinder Cap Gasket O-Ring Housing Guide Gasket Pin Pin Pan Head Screw Spring Washer Safet
Maintenance Operation Setup Safety Assembly Diagram Item 61809 For technical questions, please call 1-888-866-5797.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.