20 TON SHOP PRESS WITH OIL FILTER CRUSHER 65330 Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
Save This Manual NOTICE is used to address practices not related to personal injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
d. Keep bystanders, children, and visitors away while operating the Shop Press. Distractions are able to result in the loss of control of the tool. g. Never leave a compressed workpiece unattended. Whenever a workpiece is compressed, there is a very large amount of force that has been stored in the workpiece which must be controlled until the Press Head or Filter Crushing Head is relaxed. h.
control of the tool in unexpected situations. n. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. o. Always wear eye protection. Wear ANSI-approved safety goggles. p. Always wear hearing protection when using the Shop Press. Prolonged exposure to high intensity noise is able to cause hearing loss. q.
j. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the Shop Press’ operation. If damaged, have the Press serviced before using. Many accidents are caused by poorly maintained equipment. There is a risk of bursting if the equipment is damaged. k. Use only accessories that are identified by the manufacturer for the specific Shop Press model. Use of an accessory not intended for use with the specific model increases the risk of injury to persons.
Symbol ASSEMBLY INSTRUCTIONS Property or statement WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved eye protection. Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory Injury. Wear NIOSHapproved dust mask/respirator.
. With the help of another person, elevate and position the Air/Hydraulic Jack (21) to Top Cross Beam (22). Tighten Set Screw (25) against Ram top of the Jack. Raise Frame (7) and tighten Nut (10) to secure the Jack (21). (See Assy. Diagram.) 8. Tighten all Nuts and Bolts. 9. If you will use the unit as a common Press: Place the Press Plates (26) on the Working Bed (15). Then screw the Press Head (9) under the Frame (7). (See Assy. Diagram.) 10.
ous diagram. An in-line shutoff valve is an important safety device because it controls the air supply should the air hose rupture. allow it to build up pressure until it cycles off. 7. Adjust the air compressor’s output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool’s maximum air pressure (120 PSI) at any time. Adjust the pressure gradually, while checking the air output gauge to set the right pressure range. 8.
Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this Shop Press. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use the Shop Press until repaired. 1. 2.
l. Close the Release Valve on the Air/ Hydraulic Jack. (See Air/Hydraulic Jack Owner’s Manual.) 3. a. To operate the Shop Press as a general Press, remove the Crushing Housing (14) and Crushing Head (13) from the unit. If necessary, the Connecting Rod (11) may be removed and the Press Head (9) can be screwed under the Frame (7) directly. Follow previous instructions for the manual and pneumatic operation of the Shop Press. (See Assy. Diagram.) m.
Maintenance Instructions The lubricator’s oil level needs to be maintained and the moisture filter must be regularly drained. Performing routine maintenance on the air supply will allow the Shop Press to operate more safely and will also reduce wear on the Press. Procedures not specifically explained in this manual must be performed only by a qualified technician.
Troubleshooting Problem Possible Causes Shop Press does not work, or does not operate at its optimum capability. 1. Pressure Release Valve open. 2. Air compressor’s Regulator not set at between 110 PSI and maximum 120 PSI. 3. Loose and/or damaged Hose connections. 4. Hydraulic oil level low. 5. Trapped air in the system Damaged workpiece. Possible Solutions 1. Close Valve. 2. Set Regulator between 110 PSI and 120 maximum PSI. 3. Inspect all Hose connections. 4.
ASSEMBLY DIAGRAM SKU 65330 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.