Specifications Weight Capacity 2,000 lb. Face Plate 9-3/4" W x 5-7/8" H x 13/16" thick Wheel Diameter 3" Important Safety Information Assembly Precautions 1. Assemble only according to these instructions. Improper assembly can create hazards. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. 3. Keep assembly area clean and well lit. 4. Keep bystanders out of the area during assembly. 5. Do not assemble when tired or when under the influence of drugs or medication.
Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Leg Lock Pins (13) 1. Attach 3-1/2″ Casters (15) to the straight, back section of the Base (8) using Bolts (11), Spring Washers (10), and Nuts (9). Insert Bolts from the bottom, through the Casters first. 2.
6. Place the tops of the Braces (5) flat against the Column (2), aligning the holes. Insert Bolt (4) through the Braces and Column, and secure with Washer (7) and Nut (6). 7. Secure the bottom ends of the Braces (5) to the Base (8) using Bolts (3), Washers (7), and Nuts (6). Bolt (4) Brace (5) 8. Insert the Mounting Plate (23) through the Column (2). 9.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Mounting Engine TO PREVENT SERIOUS INJURY: Before attaching an engine to the stand, confirm that its weight does not exceed the Stand maximum capacity. 1. Lock both Legs (17) in lowered position with two Leg Lock Pins (13) per Leg secured in place with R-pins (14). 5.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM STAND FAILURE: Do not use damaged equipment. Make sure the stand is stable. If any unsafe conditions are found, take it to a qualified technician for service or repair. 1. BEFORE EACH USE, inspect the general condition of the Stand.
Parts List and Diagram Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Description Qty Pin 1 Column 1 Bolt M14×90 4 Bolt M14×100 1 Brace 2 M14 Nut 9 Ø14 Washer 9 Base 1 M8 Nut 24 Ø8 Spring Washer 24 Bolt M8×16 16 Bolt M8×16 8 Leg Lock Pin 4 R-pin 4 3-1/2″ Caster 4 3″ Caster 2 Leg 2 Handle 1 Bolt M14x70 4 Ø14 Fender Washer 4 Long Mounting Arm 2 Short Mounting Arm 2 Mounting Plate 1 Handle Grip 2 1 24 7 2 6 18 6 20 23 17 21 4 7 19 22 5 7 5 3 19 3,6,7 14 6 12 7 13 9 10 16
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
