SAVE THIS MANUAL NOTICE is used to address practices not related to personal injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
tool. Distractions are able to result in the loss of control of the tool. Personal safety a. b. c. d. e. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts.
e. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. f. Maintain the tool with care. A properly maintained tool is easier to control. g. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
A loose accessory may detach or break during operation. Symbol Definitions Symbol NPS Property or statement National pipe thread, straight WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved eye protection. WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory Injury. Wear NIOSHapproved dust mask/respirator. WARNING marking concerning Risk of Explosion. 5. Obey the manual for the air compressor used to power this tool. 6.
manual including all text under subheadings therein before set up or use of this product. hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 5. Include vibration-free periods each day of work. Unpacking 6.
before operation. Add a few more drops after each hour of continual use. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a connector and quick coupler, will make operation more efficient, but are not required. WARNING! TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Do not install a female quick coupler on the tool.
Item 66984 A B C D E F G H Air Hose Filter Regulator Lubricator (optional) Coupler and Plug Leader Hose (optional) Air Cleaner / Dryer (optional) Air Adjusting Valve (optional) Description Non-lubricated Tools A Lubricated Tools B B C C A Function A E E F H Connects air to tool Prevents dirt and condensation from damaging tool or work piece Adjusts air pressure to tool For air tool lubrication Provides each connections Increases coupler life Prevents water vapor from damaging work piece Fo
B A Item 66984 A B C D E F G H I J K L M N O Description F E F C C H H J I K J L Function L M M O N For noise and vibration reduction Secures air compressor in place Isolates sections of system for maintenance For vibration reduction Distributes air to branch lines To drain moisture from system Brings air to point of use Prevents dirt and condensation from damaging tool or work piece Prevents water vapor from damaging work piece Adjusts air pressure to tool For air tool lubrication Con
OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. 2. Route air hose along a safe route to reach work area without creating a tripping hazard or exposing air hose to possible damage.
7. Hold the handle firmly and place other hand on top of Housing (13). Then gently squeeze the Trigger (39). 8. To loosen, set the Regulator Knob to the Reverse setting. 9. Place socket (not included) over desired nut, hold handle firmly and gently squeeze the Trigger. 10.
1. Daily - Air Supply Maintenance: Every day, perform maintenance on the air supply according to the component manufacturers’ instructions. The lubricator’s oil level needs to be maintained and the moisture filter must be regularly drained. Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce wear on the tool. 2.
Problem Possible Causes Severe air 1. Cross-threaded housing leakage. components. (Slight air leakage is normal, 2. Loose housing. especially on older tools.) 3. Damaged valve or housing. 4. Dirty, worn or damaged valve. Likely Solutions 1. Check for incorrect alignment and uneven gaps. If cross-threaded, disassemble and replace damaged parts before use. 2. Tighten housing assembly. If housing cannot tighten properly, internal parts may be misaligned. 3. Replace damaged components. 4.
ASSEMBLY DIAGRAM Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 66984 For technical questions, please call 1-888-866-5797.
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.