3 in 1 Heavy Duty Tile Cutter Model 41711 Assembly & Operating Instructions www.HarborFreight.com Copyright 2000 by Harbor Freight Tools. All Rights Reserved. No portion of this manual or any artwork contained herein may be reproduced in any manner, shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
SPECIFICATIONS MODEL # 41711 TILE CUTTER Base Material: Base Size: Guide Support: Guide Bars: Guide Bar Length: Cutter Fixture:: Straight Cutter Wheel: Straight Capacity: Cutter Handle: Circle Cutter: Circle Dimension: Cutting Tip: Miter and Fence: Adjustment: Net Weight: Steel Plate, 13 ga. 7-3/4”W x 27-1/2”L Cast Aluminum 3/4” Steel Tube 25-1/2” Cast Aluminum (3 pcs.) Hardened Steel 15-3/4” 1/2” Steel Tube x 12” L Cast Aluminum 1-3/16” Min, 3-1/4” Max. Carbide Cast Aluminum 0O to 45O (5O increments) 13.
SAFETY WARNING & CAUTIONS WARNING: When using shop equipment, basic safety precautions should always be followed to reduce the risk of personal injury and hazards. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL! 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations. Don’t expose to rain. Keep work area well lit. Do not use electrically powered equipment in the presence of flammable gases or liquids. 3.
11. STAY ALERT. Watch what you are doing. Do not operate any machinery when you are tired. 12. DO NOT OPERATE MACHINERY WHILE UNDER THE INFLUENCE OF ALCOHOL, DRUGS, OR PRESCRIPTION MEDICINES. 13. CHECK FOR DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function.
ASSEMBLY Your Tile Cutter is mostly assembled when you receive it. Please complete the assembly as follows. Install the Bottom Feet. 1. Slide each Bottom Foot (#T) onto the lower corners of the Base (#V). Attach each one with the bolts, nuts, and washers supplied. Tighten the fasteners firmly. Install the Circle Cutter. Your tile cutter comes set up for making straight cuts. Whenever you wish to make circle cuts, you must install the circle cutter. Remove the circle cutter when finished. 1.
Making a straight cut. 1. Mark the desired cut on each tile piece using a grease pencil or washable marker. 2. Lift the Handle (#H), and place the tile on the EVA Cushion (#W) against the Graduation Ruler (#R) and Try Square (#U). 3. Align the mark on the tile with the direction of movement of the cutting wheel, and position the tile so the cutting wheel will move along the mark. 4. Lift the handle until the Cutting Wheel contacts the tile at one edge of the tile.
Making a Circle Cut. 1. 2. 3. 4. 5. 6. Assemble the circle cutter assembly onto the tool as previously discussed. On the tile, mark the center point of the circle, and measure or mark the circumference of the intended circle cut. Squeeze the Press Handle (#A) downward, lifting the drill point and knife body above the level of the cutter base. Place the tile on the EVA cushion, with the centerpoint of the circle directly under the center drill of the circle cutter.
MODEL # 41711 TILE CUTTER B X MODEL # 41711 TILE CUTTER PARTS LIST Part # A B C D E F G H I J K Description Press Handle Crank Housing Hole Cutter Pressing Plate Knife Body Triangle Drill Handle Rod Sliding Frame Cutting Wheel Breaking Part Page 8 SKU # 41711 Quantity 1 1 1 1 1 1 1 1 1 1 1 Part # Description Quantity L Buffer Sleeve 2 M Tracks 2 N Track Holders 2 O Hex Head Bolts 4 P Washer Sets 4 Q Wing Nut 1 R Graduation Ruler 1 S Clamp 1 T Bottom Feet w/ hardware 4 U Try Square 1 V Base 1 W EVA Cus
