Table of contents SAFETy Safety ......................................................... 2 Specifications ............................................. 5 Installation .................................................. 5 Operation .................................................... 6 Inspection ................................................... 8 Parts Lists and Diagrams .......................... 10 Warranty ....................................................
Installation Specific Safety Information NAMEpLATE AMpERES 2. Install in location that allows the operator to move and stay clear of the load. (at full load) 3. Locate pendant controls at a convenient level above the operating floor. 4. Do not install where the load hook can be lowered beyond the rated hook travel under normal operating conditions. EXTENSION cORD LENGTH 25′ 50′ 100′ 150′ 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.
Grounding Instructions SAFETy TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT GROUNDING WIRE cONNEcTION READ AND FOLLOW THESE INSTRUcTIONS: 1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This hoist is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
Model 60346 60347 60345 60344 Electrical Rating 120V~ / 60Hz / 4.1A 120V~ / 60Hz / 7.1A 120V~ / 60Hz / 8.5A 120V~ / 60Hz / 10.7A Rated Capacity 440 lb. double line 220 lb. single line 880 lb. double line 440 lb. single line 1100 lb. double line 550 lb. single line 1300 lb. double line 650 lb. single line Lifting Speed 33 FPM (single); 16.
Operation Instructions Read the ENTIRE IMpORTANT SAFETy y INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy TO pREVENT REVENT SERIOUS INJUR INJURy: Operation of a vertical hoist involves more than depressing the Up or DOWN control..
Applying the Load 2. Attach the load to the load hook securely by properly rated, suitable means, such as chains, shackles, hooks, lifting slings, etc. Load must be attached to prevent accidental disconnection. 4. Do not apply the load to the point of the hook (shown in Figure A on the right side diagram). 5. Before moving the load, make sure wire rope is not kinked or twisted or that multiple part wire ropes are not twisted around each other. 6.
Inspection, Testing, and Maintenance procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETy TO pREVENT REVENT SERIOUS INJUR INJURy y FROM AccIDENTAL OpERATION: Remove any load, release the operating controls, and detach the power cord before performing any inspection, maintenance, or cleaning procedures. TO pREVENT REVENT SERIOUS INJUR INJURy y FROM TOOL FAILURE: Do not use damaged equipment.
11. Periodic (Thorough) Hoist Rope Inspection Check entire length of rope hoist rope as follows: Inspect the individual outer wires in the strands of the rope. Keep a record of any deterioration resulting in appreciable loss of original strength, such as described below, and have a qualified technician determine whether further use of the rope would constitute a hazard: a. Check points listed in Frequent Hoist Rope Inspection on page 8. b.
parts Lists and Diagrams 60344, 60345 & 60347 parts List and Diagram SAFETy part INSTALLATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Description Housing Cap Screw M10*30 Hanging Clamp Bolt M10*26 Lock Washer - Teeth Ø10 Washer Ø10 Washer Ø10 Rope Wedge Rope Drum Rope Block Rope Crimp Wire Rope Cradle Rope Thimble Hook Drum Shaft Washer Key M5*16 Retaining Ring Ø17 Bearing (6203-2RS) Cap Screw M8*45 Stop Bracket Cross Head Bolt M5*16 Front Cover Bolt M5*17 Spring Was
60346 parts List and Diagram Qty 1 2 2 4 2 4 4 1 1 2 1 1 1 2 1 1 2 2 1 1 1 1 1 6 10 2 1 1 part 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 52 53 54 55 56 57 Description Secondary Gear Gasket Gearbox Bearing (6202-2RS) Rotor Stator Motor Housing Spring Brake Drum Gear Cover Bolt M5*140 Washer Ø5 Washer Ø3 Cross Head Bolt M3*6 Fan Hood Fan Blade Hex Socket Screw Upper Junction Box Cable Terminal Block Cord Clamp Screw M3*14 Screw ST3.
pLEASE READ THE FOLLOWING cAREFULLy AREFULL AREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.