User Guide

ManualsBrandsHarbor Freight Tools ManualsHair Clipper47082

ELECTRIC CLIPPER

Model

47082

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2008 by Harbor Freight Tools

this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools. Diagrams

within this manual may not be drawn proportionally. Due to continuing improve-

ments, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised Manual 09k

Summary of content (8 pages)

PAGE 1
electric clipper Model 47082 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
PAGE 2
Specifications Accessories Electrical Input Comb Attachment (w/ 4 Settings) Barber Comb Cleaning Brush Scissors Lubricant (One Tube) E316219 120 V~, 60 Hz, 8-13 W Save This Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover.
PAGE 3
5. Keep the cord away from heated surfaces. 6. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like. 7. Never drop or insert any object into any opening. 8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. 9. Do not use this appliance with a damaged or broken comb. 10.
PAGE 4
Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Operation Instructions Blade Alignment • The Clipper comes oiled and aligned from the factory. Blades must be realigned after they have been removed for cleaning or replacement. 1. To realign blades, match the upper and lower blades teeth up, point for point.
PAGE 5
• Before turning the Clipper off, rapidly move the Blade Lever from close cut to longer cut twice. This will clear trimmings from the Clipper. Cutting Hair Attachment Comb #1 leaves 3mm (1/8 inch) hair length. Attachment Comb #2 leaves 6mm (1/4 inch) hair length. Attachment Comb #3 leaves 9mm (3/8 inch) hair length. Attachment Comb #4 leaves 12mm (1/2 inch) hair length. • The Comb’s sizes are marked on the outside middle surface.
PAGE 6
8. Change to Comb #3 or #4 and, working upwards, cut the hair on the back and top of the head (see diagram 2 & diagram 3). 9. Using Comb #3 or #4, cut hair on top of head from back to front, against the direction in which the hair normally grows. In some cases, this may require changing direction (see diagram 4). 10. Comb #1 or #2 can be used to achieve very close “crew” cuts. 11. For longer hair, use the provided comb to lift the hair away from the top of the head.
PAGE 7
13. To cut the sideburns, change Comb to #1 or #2. To produce a clean, straight line for the sideburns, reverse the Clipper by turning the bottom side upwards (see diagram 7). 14. Press the Clipper at a right angle to the head, with the tips of the blades lightly touching the skin and work downwards to obtain a clean, razor-like cut. 15. Comb through hair to check for uneven strands and ensure an even cut. Short tapered styles 1. Starting with Comb #4, cut from the back of the head to the top of the head.
PAGE 8
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.