NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Table of Contents Safetye�������������������������������������������������2 Specifications......................................5 Setup...................................................6 Operationa�������������������������������������������11 Maintenancei��������������������������������������13 Parts Lists and Diagram.....................18 Warranty.................................
NOTICE Personal Safety c. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. d. b. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair increases the risk of injury to persons e. as a result of being caught in moving parts. Use safety equipment.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Air Source a. Setup Never connect to an air source b. Never use oxygen, carbon dioxide, that is capable of exceeding combustible gases or any bottled 85 psi. Over pressurizing the tool gas as an air source for the tool. may cause bursting, abnormal Such gases are capable of explosion operation, breakage of the tool or and serious injury to persons. serious injury to persons.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. 4. Read all of the information concerning coating products and cleaning solvents. Do not use chlorinated solvents (e.g. 1‑1‑1 trichloroethylene and dichloromethane, also known as methylene chloride) to clean airbrushes. Many airbrushes contain aluminum, which reacts strongly to chlorinated solvents.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Functions Adjustment Screw Trigger Nozzle (Not Visible) Air Cap Air Inlet Color Stem Setup Lid Fitting Lid Glass Jar Airbrush Holder Operation Air Inlet Air Hose Maintenance Inlet/Outlet Connector Air Pressure Valve Figure A Page 6 For technical questions, please call 1-800-444-3353.
NOTICE Initial Set Up Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Air Supply Setup TO PREVENT SERIOUS INJURY FROM EXPLOSION: Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. Setup 1.
Item 69861 For technical questions, please call 1-800-444-3353. Maintenance A Air Hose B Filter D Regulator E Coupler and Plug C Air Cleaner / Dryer* F Air Adjusting Valve* *Optional components.
For technical questions, please call 1-800-444-3353. D E F G H C F E Function F G I I J Filter Description J H L Coupler and Plug J Regulator K Lubricator* I N K M Leader Hose* N Air Cleaner / Dryer* O Air Adjusting Valve* *Optional components. Non-lubricated Tools C C For noise and vibration reduction Secures air compressor in place Isolates sections of system Ball Valve for maintenance Isolation Hose For vibration reduction Main Air Line - 3/4″ min.
NOTICE Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Workpiece and Work Area Set Up 2.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety General Operation IMPORTANT: Proper spraying technique is ESSENTIAL to achieve good results. 5. For very fine detail work, you may decrease the distance up to 1” from the workpiece. 1. Press down on the Trigger to release air from the Nozzle. Slowly and gently draw back on the Trigger to release paint from the Needle. The air will atomize the paint and create a fine spray.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY: Detach the air supply and safely discharge any residual air pressure in the tool before performing any inspection, maintenance, or cleaning procedures.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Cleaning TO PREVENT INJURY: Needles are very sharp. Use extreme caution when handling needles. Solvent Selection 1. Disconnect from the air source. Follow the paint manufacturer’s recommendations for cleaning, solvent type, and disposing of used solvent. 2.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety Air Supply Maintenance Every day, perform maintenance on the air supply according to the component manufacturers’ instructions. Storage Maintenance Operation Setup Store in a dry, secure area out of reach of children. Item 69861 For technical questions, please call 1-800-444-3353.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush. Safety General Troubleshooting Chart Problem Poor Paint Atomization Possible Causes Likely Solutions 1. Low paint level. 1. Refill. 2. Paint not properly thinned. 2. Thin paint. 3. Clogged Nozzle. 3. Clean Nozzle. 4. Loose/damaged Needle. 4. Adjust or replace Needle. 1. No pressure at Airbrush. 1. Check air hoses. 2. Air Pressure Valve not open enough. 2.
NOTICE PLEASE READ THE FOLLOWING CAREFULLY Setup THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
NOTICE Clean the Airbrush IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Airbrush.
NOTICE Part Description Holder Bushing Screw Steel Column Spring Clip Card Steel Ball Airbrush Holder O-Ring Washer Turnplate Washer Gauge Holder Air Pressure Gauge Base Connector Qty 2 1 1 1 1 2 1 6 1 1 1 1 1 1 1 Part 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Description O-Ring Inlet/Outlet Connectors Adjustment Screw O-Ring Valve Holder O-Ring O-Ring Base 1 Base 2 Suction Cup Air Hose Connector Adapter 1/4" - 18 NPT Case Qty 1 7 1 1 1 1 1 1 1 3 7 14 1 1 Maintenance Operation 27 28 29 30 31 32 3
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.