Table of Contents SAFETY Safety.......................................................... 2 Maintenance............................................... 16 Specifications.............................................. 7 Setup........................................................... 8 Operation.................................................... 12 Parts List and Diagram............................... 18 Warranty.....................................................
IMPORTANT SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING – When using tools, basic precautions should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons. c.
Tool use and care SAFETY a. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and can lead to loss of control. b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed. c. Do not use the tool if the trigger does not turn the tool on or off.
Specific Safety Instructions 3. Choice of triggering method is important. Check manual for triggering options. 4. Always assume the tool contains fasteners. 5. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 6. Do not actuate the tool unless the tool is placed firmly against the workpiece. 20. Do not fire fasteners into a workpiece that has people, utility lines, or other objects behind or inside it. 21. Keep balance while using this tool.
Vibration Precautions SAFETY This tool vibrates during use. Repeated or long‑term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use.
Functional Description Maximum Air Pressure 120 PSI Air Inlet 1/4″ -18 NPT Air Consumption 2 CFM @ 90 PSI Safety Mechanism Type Nail Type SAFETY Specifications Full Sequential as shipped red Contact Trip trigger included 0.120″ Diameter Shank, 3/4″ ~ 1-3/4″ Long Components and Controls Exhaust Trigger OPERATION SETUP Air Inlet Magazine Safety Nosepiece Latch Shingle Guide Item 67450 For technical questions, please call 1-800-444-3353.
Initial Tool Set Up/Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
TO PREVENT EXPLOSION: Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. Note: This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool.
Description Non-lubricated Tools A Air Hose Filter Regulator Lubricator (optional) Coupler and Plug Leader Hose (optional) Air Cleaner / Dryer (optional) Air Adjusting Valve (optional) MAINTENANCE A B C D E F G H OPERATION Lubricated Tools C SETUP B B C A Function A E E F H Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapo
Item 67450 For technical questions, please call 1-800-444-3353.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Workpiece and Work Area Set Up 1. Designate a work area that is clean and well‑lit. The work area must not allow access by children or pets to prevent distraction and injury. 2.
Contact Safety Trip (Bump Fire) Mechanism Definition SAFETY The contact safety trip (or bump fire) mechanism allows rapid fire. The RED TRIGGER enables the contact safety trip mechanism. The tool should only fire if the Safety Nosepiece is pressed against the workpiece and the trigger is pulled. It should fire again if the trigger is released and pulled OR if the safety is lifted and pressed against the workpiece again. The Tool should not fire if the Safety Nosepiece is not pressed against an object.
Loading the Tool SAFETY TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply. • Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners. 1.
1. Before each use, test the tool as directed in the prior section. 5. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. The adjuster can also be used to correct the firing depth. 2. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use.
User-Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETY TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams): • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply.
Troubleshooting 3. Incorrect lubrication or not enough lubrication. 4. Blocked air inlet screen (if equipped). 5. Mechanism contaminated. 1. Adjust depth setting, if available. 2. Check for loose connections and make sure that air supply is providing enough air pressure (PSI) to the tool’s air inlet. Do not exceed maximum air pressure. 3. Lubricate using air tool oil and grease according to directions. 4. Clean air inlet screen of buildup. 5.
Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY SAFETY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
OPERATION SETUP SAFETY Assembly Diagram Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. MAINTENANCE Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 67450 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.