Table of Contents Safety.......................................................... 2 Setup........................................................... 3 Operation..................................................... 4 Maintenance................................................ 6 Parts Lists and Assembly Diagrams............ 8 Warranty..................................................... 11 SAFETY WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol.
Setup - Before Use: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Note: For additional information regarding the parts listed in the following pages, refer to Parts Lists and Assembly Diagrams on page 8.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Tool Set Up Attaching the Handle 1. Fasten the Upper Handle to the Lower Handle. 3. Tighten the Set Screw. 2. Loosen the Set Screw and insert the assembled Handle into the Handle Socket. Bleeding 1. Loosen the Fill Screw. 2. Insert the Handle into the Handle Socket to operate the Release Valve. 4.
General Operating Instructions 1. Turn the Handle counterclockwise to lower the Jack. Once the Jack is fully lowered, turn the Handle firmly clockwise to close it. 2. Carefully position the Saddle of the Jack under the vehicle manufacturer’s recommended lifting point. (See vehicle manufacturer’s owner’s manual for location of frame lifting point.) 3. Pump the Handle until the top of the Jack’s Saddle has nearly reached the vehicle lifting point.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETY TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication SETUP 1. Before each use, inspect the general condition of the Jack.
Troubleshooting SAFETY TO PREVENT SERIOUS INJURY: Use caution when troubleshooting a malfunctioning jack. Stay well clear of the supported load. Completely resolve all problems before use. If the solutions presented in the Troubleshooting guide do not solve the problem, have a qualified technician inspect and repair the jack before use. After the jack is repaired: Test it carefully without a load by raising and lowering it fully, checking for proper operation, BEFORE RETURNING THE JACK TO OPERATION.
Parts Lists and Assembly Diagrams 68048 Parts List and Assembly Diagram SAFETY Part SETUP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Description Retaining Ring (M20) Washer Front Wheel Frame Retaining Ring (M16) Bolt Retaining Ring (M22) Hydraulic Adaptor Lift Arm Assembly Saddle Saddle Screw Retaining Ring (M25) Lift Arm Shaft Pin (M4x45) Spring Hydraulic Unit Bolt Washer (M18) Set Screw Qty 2 2 2 1 2 2 2 1 1 1 1 2 1 1 2 1 2 2 1 Part 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Descr
68049 Parts List and Assembly Diagram Qty 2 2 2 1 4 4 4 2 4 4 2 2 1 1 1 1 Part 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description Set Screw Upper Handle Lower Handle Screw (M6X35) U-Joint Hydraulic Unit Spring Retaining Ring (M22) Hydraulic Unit Adaptor Pin (A4x55) Retaining Ring (M25) Lift Arm Shaft Cover Plate Saddle Saddle Screw Handle Bumper Qty SAFETY Description Retaining Ring (M20) Washer (M20) Front Wheel Frame Nut (M16) Washer (M16) Screw (M5X12) Rear Caster Assembly Screw (M10X20)
68056 Parts List and Assembly Diagram SAFETY Part SETUP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Description Retaining Ring (M20) Front Wheel Washer Front Wheel Frame Rear Caster Screw (M12X25) Washer (M12) Washer (M16) Retaining Ring (M30) Screw (M5X12) Screw (M8X20) Washer (M8) Tie Rod Bolt Washer (M18) Nut (M16) Rubber Bumper Upper Handle Screw Qty 2 2 2 1 2 4 4 4 2 4 4 4 2 2 2 4 2 1 1 Part 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Description Lower Handle Set Screw Handle
Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
3491 Mission Oaks Blvd.
