Table of Contents SAFETY Safety.......................................................... 2 Specifications............................................. 10 Setup.......................................................... 10 Operation.................................................... 11 Maintenance............................................... 13 Parts List and Diagram............................... 14 Warranty.....................................................
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 5. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Power Tool Use and Care SAFETY 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.
3. Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece. 4. Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control. 5. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Circular Saw Safety Warnings (continued) SAFETY 12. Lower guard should be retracted manually only for special cuts such as ″plunge cuts″ and ″compound cuts.″ Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. 13. Always observe that the lower guard is covering the blade before placing saw down on bench or floor.
Vibration Safety 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
Grounding SAFETY TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A on page 9.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Table A.) 7.
Specifications SAFETY Electrical Rating 120V~ / 60Hz / 10A Motor No Load Speed 5500 RPM LASER LIGHT DO NOT STARE INTO BEAM Maximum Blade Diameter 7-1/4" Max. Output: <1 mW, Wavelength: 650 nm CLASS II LASER PRODUCT Arbor 5/8" Depth of Cut 2-7/16" @ 90° 1-5/8” @ 45° Bevel Capacity 0° to 45° Laser Battery Type 2 AAA (included) This product complies with 21 CFR 1040.10 and 1040.11 Diode Mfr.: Zhenjiang Bouncer Stone Electron Co., LTD, No. 16 Guyang Xincun Dingmao Zhenjiang City.
Operating Instructions Tool Set Up 2. Depress the Spindle Lock Lever to hold the Saw Blade in place and unscrew (clockwise) and remove the Blade Clamp Bolt and Outer Flange. 3. Pull the Lower Guard all the way up into the Upper Guard. Remove the old Saw Blade and install a new Saw Blade onto the Shaft. Note: Make sure to install the new Saw Blade with its teeth and the arrow on the Saw Blade pointing in the same direction as the arrow on the Lower Guard. Spindle Lock Lever SETUP 1.
Batteries for Laser 1. Unthread the Screw holding the Battery Cover in place. Screw Battery Cover 2. Remove the Screw and Battery Cover. SAFETY 3. Install 2 AAA batteries matching polarity with markings on compartment. 4. Replace the Battery Cover and secure in place with the Screw. Dust Collector 1. Connect a Dust collection system (sold separately) to the Dust Chute on the Stationary Guard. Figure 6 Work Piece and Work Area Set Up 1. Work piece selection: a.
Maintenance and Servicing SAFETY Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Release the Trigger, turn off the laser and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY SAFETY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Item 69078 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.