Product manual

ManualsBrandsHarbor Freight Tools ManualsDiagnosticHarbor Freight Tools 7 Function Digital Multimeter

7 FUNCTION DIGITAL MULTIMETER

OPERATING INSTRUCTIONS

Visit our Web site at http://www.harborfreight.com

2011 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be

reproduced in any shape or form without the express written consent of

Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

69096

REV 12a

Summary of content (7 pages)

PAGE 1
7 FUNCTION DIGITAL MULTIMETER 69096 OPERATING INSTRUCTIONS Visit our Web site at http://www.harborfreight.com REV 12a Copyright© 2011 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
PAGE 2
Specifications Frequency 45-450 Hz DC Amps Ranges: 200µA/2000µA/20mA/200mA, 10A Accuracy DC Voltage (@200µA-200mA) 1.2%±2D; (@10A) 3%±2D Ranges: 200mV/2000mV/20/200/1000V Accuracy AC Voltage (@200mV) 0.5%±1D; (@2000mV-200V) 1.0%±1D; (@1000V) 1.0%±2D Ranges: 200/750V Accuracy Resistance (45-450 Hz) 1.2%±10D Ranges: 200/2000/20K/200K/2000K Ohm Accuracy (@200-200K Ohm) 0.8%±2D; (@2000K Ohm) 1.0%±2D; Sampling Rate 2.
PAGE 3
Read all instructions before using this tester! 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Avoid working alone. If an accident happens, an assistant can bring help. Keep work area clean. Cluttered areas invite injuries. Avoid electrical shock. Use extreme caution when using this tool near uninsulated conductors or bus bars. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and cabinet enclosures when testing voltages. Avoid damaging meter.
PAGE 4
Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 16. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 17.
PAGE 5
4. 5. Be careful not to apply voltage DC Volt to the Test Leads Selection Area when they are connected Ohm t o t h e C O M Selection Area (Bottom) and VΩmA (Center) Jacks and the Transistor Multimeter is in /hFE Jack an Ohms testing setting. Damage can occur to the multimeter or the fuse may blow. Do not switch between testing modes with the multimeter connected to a circuit.
PAGE 6
DC Current Measurements Measure DC conductors carrying up to 10 amperes. 1. Turn the Range Selector Switch to the 10A position. Always start with the highest range if the amperage is unknown. 2. Plug the red lead into the 10A (Top) Jack. Plug the black lead into the COM (Bottom) Jack. Switch the Multimeter ON. 3. Carefully touch the exposed conductors with the tips of the probes to measure the amperage. Note: Amperage is always tested in series with the circuit under test. 4. Read measurement.
PAGE 7
4. The approximate forward voltage drop of the diode will be displayed in mV. If the connection is reversed only “1” will be shown. Battery Charge Measurement Test the amount of charge left in batteries. NOTE: This setting is for testing the charge of small 9V or 1.5V batteries only. Never use this setting to test automotive or lead-acid batteries. The high current could cause damage to the meter and/or cause severe personal injury.