VERTICAL FLOAT SUMP PUMP Model 95591 - .75 HP Model 95592 - 1 HP Model 95593 - 1.5 HP Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product.
SPECIFICATIONS Model 95591 Motor 115 V~ / 60 Hz / 4 A / 3/4 HP Model 95592 Model 95593 115 V~ / 60 Hz / 5.5 A 115 V~ / 60 Hz / 6 A / 1 HP / 1.5 HP Automatic Float Switch 3-Prong / Grounded Yes 3,000 GPH 3,300 GPH 3,700 GPH 20’ 24’ 26’ 1-1/4 NPT Female / 1-1/2 NPT Male 95° Fahrenheit Power Switch Type Power Plug Type Self Priming Maximum Pumping Capacity Maximum Delivery Height Discharge Diameter Max.
WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Children and other unauthorized people should not be allowed in the work area. a polarized outlet.
TOOL USE AND CARE 1. 2. 3. Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the Sump Pump. Such preventive safety measures reduce the risk of starting the unit accidentally. Store idle equipment out of reach of children and other untrained persons. Electrically-powered products are dangerous in the hands of untrained users.
6. Do not pump hazardous materials. Do not pump explosive or flammable materials such as fuel, oil, kerosene, gasoline, etc. Do not pump in close proximity to flammable or explosive materials. Do not pump fats, oils, salt or waste water. This Pump is designed to move clean or dirty water only. Do not pump water hotter than 95 degrees Fahrenheit. 7. Secure the discharge pipe (not included) to a solid surface to ensure the stability of the Pump. 8. Position the Pump on a flat, level, solid surface.
Grounding To prevent electric shock and death from incorrect grounding wire connection: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
3. 4. 5. 6. 7. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.) The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Table A.
UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 12 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY AND OPERATING INSTRUCTIONS Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 13.
FIGURE E CHECK VALVE OR UNION (NOT INCLUDED) 1-1/4” OR 1-1/2” NPT PVC TO 115 VOLT, GROUNDED GFCI OUTLET DISCHARGE PIPE (NOT INCLUDED) o 1/8” AIR BLEED HOLE BASE (25) 3. Connect the Discharge Pipe to the Base (25). NOTE: Make sure the Discharge Pipe is secured to a solid surface, with appropriate hardware (not included), to ensure the stability of the Pump. (See Figure E.) 4.
6. Carefully set the Pump in place. Do not lower or raise the Pump by the Power Cord or Discharge Pipe. (See Figure E.) 7. The Float Switch (2) automatically switches on and off at a water depth of approximately 4 inches. The ON/OFF height can be manually changed by adjusting the Float Switch Lock. CAUTION: Do not run the Pump dry. Doing so will increase wear to the unit and possibly cause seal damage. (See Figure E.
2. To clean the Impeller Cover and Impeller: A clogged or dirty Impeller Cover or Impeller (28) will greatly reduce performance of the Pump. To clean the Impeller Cover (31), spray the Cover with clean water. To clean the Impeller, remove the nine Screws (32) at the bottom of the Base (25). Then, remove the Base to expose the Impeller Cover and Impeller. Use a stream of clean water to clean the Impeller and Impeller area inside the Pump. Then, replace the Base. (See Assy. Diagram.) 3.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.
SKU 95591/95592/95593 32 31 30 29 28 27 26 25 24 Power Cord/Plug not shown. 23 22 19 17 11 9 7 5 3 1 Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. *Internal Motor Parts Are Not Consumer-Serviceable.
Limited 1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.