Wet/dry vacuum, 16 gallon, 6.5 HP Model 96325 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2007 by Harbor Freight Tools®. All rights reserved.
Specifications Electrical Requirements 120 V~ / 60 Hz Amp Draw 10 A Air Flow 88.3 CFM Horsepower 6.5 Filter Dimensions 7.5” Dia. x 6.6” H Accessories 6.8’ Hose Floor Brush Crevice Tool Utility Brush Stainless Steel Canister Dust Bag Storage Box Two 19” L Extension Wands Overall Dimensions 27.95” H x 18.11” W x 19.
. Keep bystanders, children, and visitors away while operating the Vacuum. Distractions can cause you to lose control. Never allow children to play with or operate the Vacuum. Protect others in the work area from debris. Provide barriers or shields as needed. Electrical Safety 1. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs.
3. Avoid accidental starting. Be sure Off Button (2) is depressed before plugging in. Plugging the Vacuum in with the On Button (3) depressed, invites accidents. 4. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the Vacuum in unexpected situations. 5. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
2. When servicing the Vacuum, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. For Household use only. This product is not to be used for any industrial applications. 2. For use indoors only. This product is not suited for use outdoors. 3.
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 or 240 VOLT) NAMEPLATE AMPERES EXTENSION CORD LENGTH (at full load) 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - TABLE A * Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Instructions Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1.
. Place the Vacuum Assembly onto the top of the Canister, catch the edge of the Canister with the Latches, and move the Latches upward to secure. The Vacuum Assembly mechanism is located at the top part of the Vacuum Canister. 11. Connect the Hose to the inlet of the Vacuum at the rotate clockwise to lock hose into position. For dry applications use the upper hose connection, and for wet applications use the lower connection. 12.
HEPA Frame (16) HEPA Filter (25) on HEPA Frame (16) HEPA Filter (25) on HEPA Frame (16) with HEPA Cover (26) • The HEPA Filter should be rinsed with clean water periodically and allowed to air-dry completely before being used again. Do not use compressed air to speed up the drying process. • The HEPA Filter should be removed before vacuuming up liquids to prevent it from becoming fouled and obstructing air-flow. Vacuuming Before each use, inspect the general condition of the Vacuum.
6. The Vacuum must be emptied into a proper waste fluid drain before continuing use. Remove the Drain Cover (21) to empty the Vacuum, replace the Drain Cover, and resume work. 7. It is recommended Vacuum be thoroughly rinsed with clean water after each use. Using the Vacuum for dry applications: 1. WARNING! Make sure the Off Button (2) is depressed before plugging the Vacuum into a standard 120V outlet. 2. Attach the appropriate attachment to vacuum.
3. After each use, empty the Canister (19), and wash with warm, soapy water. Wipe out with clean, dry cloth. Troubleshooting Problem Probable Solutions Power Switch does not turn unit on. 1. Make sure power cord is plugged into a working 120 Volt, grounded, electrical outlet. 2. Canister is full. Empty Canister. 3. Have a qualified service technician check out the power switch, wiring, and motor. Unit shuts down during use. 1. Canister is full. Empty Canister. 2.
Limited 1 year / 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of one year from date of purchase that the tank is free of defects in materials and workmanship (90 days if used by a professional contractor or if used as rental equipment).
ASSEMBLY DIAGRAM SKU 96325 For technical questions, please call 1-800-444-3353.
