air punch/flange tool Model 01110 Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2007 by Harbor Freight Tools®. All rights reserved.
Specifications Maximum Sheet Metal Capacity 16 Gauge Mild Steel Air Inlet 1/4” NPT Female Air Consumption 4 CFM @ 90 PSI Recommended Air Pressure 90 PSI Throat Depth 5/8” Crimp Width 7/8” Punch Size .19” Hole Placement .
of drugs, alcohol, or medication. A moment of inattention while operating may result in serious personal injury. 2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Avoid accidental starting. Be sure the Throttle Lever (20) is NOT depressed before attaching to air supply.
Service 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk damage to your project and/or personal injury. SPECIFIC SAFETY RULES 1.
Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Instructions NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 10 of this manual.
Operation Instructions PUNCHING 1. WARNING: Always wear heavy-duty leather gloves when handling sheet metal. Sharp edges can cause severe injury. Always wear ANSI-approved safety goggles. 2. Pre-mark the desired location of each hole you wish to punch on the workpiece. NOTE: If the workpiece is to be both punched and flanged, flange it first, then measure for the hole placement. Flanging will change the dimensions of the workpiece. 3. Connect the Air Punch/Flange Tool to your air supply.
. Repeat steps 5 and 6 until until the entire length you wanted to flange is finished. 8. Disconnect the air supply. 9. WARNING: After disconnecting the Air Punch/Flange Tool from the air supply there could still be enough air pressure to fire the Punch/Flange. After making sure the air supply is disconnected, ALWAYS fire the Punch/Flange repeatedly to make sure all air is bled from the tool.
INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Throttle Lever (20) is in its “OFF” position and that the Air Punch/Flange Tool is disconnected from its air supply before performing any inspection, maintenance, or cleaning procedures. 1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation.
Troubleshooting Problem Possible Causes Punch/Flange will not start Probable Solutions 1. Air supply not connected. 2. Air hose/hoses not securely connected, or damaged and leaking air. 1. Check, make sure air supply is properly connected to the tool. 2. Check all air hose and connections. if any air hose damage is found, replace the damaged hose/hoses. Do not apply duct tape or wraps of any kind to the damaged area. Punch/Flange will 1.
ASSEMBLY DIAGRAM REV 07e SKU 01110 For technical questions, please call 1-800-444-3353.
90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
