Product manual

ManualsBrandsHarbor Freight Tools ManualsSpecialty ToolsHarbor Freight Tools Crossbar Dent Repair Kit

CROSS BAR

DENT REPAIR KIT

66957

INSTRUCTIONS AND

PRECAUTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

SAVE THESE

INSTRUCTIONS.

READ ALL

PRECAUTIONS AND

INSTRUCTIONS.

2009 by Harbor Freight Tools

. All

rights reserved. No portion of this document or any

artwork contained herein may be reproduced in any

shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this document

may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the

product described herein. Tools required for assembly

and service may not be included.

For technical questions or replacement parts,

please call 1-800-444-3353.

Please note: Harbor Freight Tools is not

responsible for damage to vehicle nish result-

ing from use of this product.

SPECIFICATIONS

Glue Gun 120VAC / 60 Hz / .33 A

Crossbar Adjustment 3” min. to 5” max.

UNPACKING

When unpacking, make sure that the item is

intact and undamaged. If any parts are missing or

broken, please call Harbor Freight Tools at

1-800-444-3353 as soon as possible.

IMPORTANT SAFETY

INFORMATION

Wear ANSI-approved safety goggles and 1.

heavy-duty work gloves during use.

Contains glue; keep away from children. 2.

This product is not a toy. Do not allow chil-

dren to play with or near this item.

Use as intended only.3.

Inspect before every use; do not use if parts 4.

are loose or damaged.

Maintain product labels and nameplates. 5.

These carry important safety information.

If unreadable or missing, contact Harbor

Freight Tools for a replacement.

INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the

beginning of this document including

all text under subheadings therein

before set up or use of this product.

Insert Glue Stick (2) into Glue Gun (1). Plug 1.

in Glue Gun and allow to warm up for ten to

fteen minutes before use.

Using clean cloth (not included), clean dent 2.

area with Release Agent (3). Then apply

heated glue from Glue Gun to end of desired

Pull Tab (4).

Place Pull Tab on center of dent and hold 3.

there for ten seconds. WARNING! Do NOT

push Pull Tab against dent.

Place Cross Bar (5) over Pull Tab, setting 4.

Adjusters (9) to desired length. Thread

Wing Nut (6) onto end of Pull Tab. Continue

to twist Wing Nut until dent is raised. Stop

when dent returns to normal surface level.

Unthread Wing Nut and remove Cross Bar 5.

and Pull Tab from surface. Apply two drops

of Release Agent to spot of dried glue. Use

Scraper to peel off softened glue patch.

If a high spot has been created, use a ham-6.

mer (not included) and lightly tap Dowel (8)

against raised spot until desired smoothness

is reached.

Note: 7. The Repair Kit will not repair ALL kinds

of dents, regardless of size. The Repair Kit

will also not work on aluminum panels or

surfaces.

Summary of content (2 pages)

PAGE 1
Cross Bar Dent REPAIR kit 66957 Instructions and precautions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Important SAFETY Information 1. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. 2. Contains glue; keep away from children. This product is not a toy. Do not allow children to play with or near this item. 3. Use as intended only. 4.
PAGE 2
Parts List & diagram Part 1 2 3 4 5 6 7 8 9 Description Qty. Glue Gun Glue Stick Release Agent Pull Tab Cross Bar Wing Nut Scraper Dowel Adjuster 1 3 1 2 1 1 1 1 2 6 5 9 7 4 1 Please note: Release Agent (3) not shown. 8 2 Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.