Electric Pressure Washer 68333 - Electric Pressure Washer Read this material before using this product. Failure to do so can result in serious injury. Save this manual. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Visit our website at: http://www.harborfreight.com Copyright© 2011 by Harbor Freight Tools®. All rights reserved.
Safety Warnings Specifications Electrical Input 120 V~ / 60 Hz / 12 A (Rated) Maximum 1,500 PSI Pressure Maximum 1.3 GPM Flow Rate High Pressure 13 ft. Hose Power Cord 1. Read all the instructions before using the product. 2. To reduce the risk of injury, close supervision is necessary when a product is used near children. 3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls. 35 ft. 4. Stay alert – watch what you are doing.
Set up Precautions 1. The work area should have adequate drainage to reduce the possibility of a fall or electric shock due to wet surfaces. 2. Wear ANSI-approved safety goggles during set up and use. 3. Only feed cold, clean water through this tool. Pressure washer detergent may be used in the soap dispenser only. Do not use caustic materials, solvents, flammable materials, or detergents not designed for pressure washers. Use of any such material can cause injury, or damage this tool or personal property.
caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3.
Ground Fault Circuit Interrupter Protection This pressure washer is provided with a groundfault circuit-interrupter (GFCI) built into the plug of the power-supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. Servicing a Double-Insulated Appliance In a double-insulated product, two systems of insulation are provided instead of grounding.
Instructions for Putting into Use Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. water pressure from the unit before assembling or making any adjustments to the tool. Check the Inlet Strainer for any blockage, including packaging debris. The Pressure Washer may be shipped with a plastic plug in the Inlet.
Assembly 1. Snap the Body onto the Base until it clicks into place. 2. Attach the Handle to the front of the Body with four of the Screws. 3. Attach the Strap for the Soap Dispenser to the Base with the remaining two Screws. 4. Thread the High Pressure Hose onto the Pressure Hose Outlet on the front of the body. 5. Snap the High Pressure Hose to the Spray Gun until it clicks in place. 6. Place the Water Filter in the Water Supply Inlet and thread the adapter onto the Inlet.
Features Operating Instructions Note: Familiarize yourself with the location and function of all of the machine’s controls before proceeding to setup of the machine. 1. This item is equipped with a GFCI (Ground Fault Circuit Interruption) plug. Read and follow these GFCI precautions: WARNING! To prevent electric shock and death: Test GFCI (Ground Fault Circuit Interrupter) before each use as follows: INDICATOR RESET BUTTON TEST BUTTON FIGURE A a.
direction. You will have a clearer idea of the time involved to clean the area after doing a test run. 5. Clear the cleaning area of all objects that are not being cleaned. If any water prone or delicate items cannot be moved, protect them. If detergent is to be used, cover or remove any plants or animals that may be damaged by the detergent. Disconnect power to and protect any nearby electrical wiring from water and spray. 6.
General Operating Instructions 1. Point the Nozzle in a safe direction and squeeze the trigger to check that all pressure is released from the unit. Release the Trigger. 2. Turn on the water supply, then turn on the Power Switch. Note: If the unit does not turn on or turns off suddenly, check and reset the GFCI. 3. Unlock and squeeze the Trigger to start the stream. Be aware that when it is first started, the gun will kick back. 4.
cleaning efficiency. Turn on the water source and power, and rinse off all detergent completely. 8. Hold the Water Gun at about a 45° angle and steadily sweep the stream back and forth; if a severe, head-on angle is used, dirt may imbed in the surface being cleaned. Follow a steady, consistent pace during cleaning; this will help prevent stripes or discoloration afterwards.
Maintenance and Servicing To prevent serious injury from accidental operation: Turn the Power Switch of the tool off, unplug the tool from its electrical outlet, shut off the water supply and safely discharge all residual water pressure from the unit before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Troubleshooting Problem Possible Causes Pressure Washer will not start 1. Cord not connected. 2. No power at outlet. Pressure Washer Stops suddenly 3. GFCI circuit breaker tripped. 4. Internal damage or wear. (Carbon brushes or switch, for example.) 1. GFCI circuit breaker tripped. 2. Water leaking from housing. Output pressure varies 1. Not enough water supply. 2. Air in water supply. 3. Water Inlet Filter is clogged. 4. Extension Nozzle not attached to Spray Gun. 5. Nozzle is clogged. 6.
Parts List and Assembly Diagram PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
Parts List and Assembly Diagram Assembly Diagram 2 9 1 1 5 3 12 16 4 21 M 11 10 22 8 M OIL: SAE 15/W40 gr. 70 M1 M2 M3 M4 M5 M6 M16 M8 M9 M13 M15 M7 M12 SKU 68333 M11 M10 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.