WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
16. Do not leave the Light unattended when it is plugged into an electrical outlet. Turn off the Light, and unplug it from its electrical outlet before leaving. 17. This product is not a toy. Keep it out of reach of children. 18. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: • Avoid operating alone.
Grounding TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the Light. Never remove the grounding prong from the plug. Do not use the Light if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
Symbology WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields. Double Insulated Canadian Standards Association Read the manual before set-up and/or use. Underwriters Laboratories, Inc. V~ A n0 xxxx/ min. Volts Alternating Current Amperes No Load Revolutions per Minute (RPM) WARNING marking concerning Risk of Fire. Do not cover ventilation ducts. Keep flammable objects away. WARNING marking concerning Risk of Electric Shock.
Set Up Instructions Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual, including all text under subheadings therein before setup or use of this product. Risk of accidental starting, resulting in serious personal injury. Turn the Power Switch of the Light OFF and unplug it from the electrical outlet before assembling or making any adjustments. Deviation from the assembly instructions may result in a risk of fire or electric shock.
Light Assembly For each light: 1. Remove the Bolt at the top of the housing and open the Lamp Cover. See Figure D. Bolt 4. Close the Lamp Cover (22) and secure with the Bolt (25). 5. Place Handle (1) over end of Bolt (25) and secure in place with Wing Nut (2). 6. Gently squeeze the Wire Cover (23) while placing its four tabs into the Lamp Cover (22). Secure the tab on the Wire Cover to the Lamp Cover using the Screw (52). (See Figure E) 22 23 Figure D 2.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual, including all text under subheadings therein before setup or use of this product. 1. Plug the Light into a standard 120V grounded, electric outlet. 2. Push the On/Off switch on the back of the light. 3. WARNING! Keep the Light away from combustible objects. The light and housing will get hot enough to start a fire. Page 8 4. To turn off, push the On/Off switch. 5.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the On/Off Button is in the OFF position and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM LIGHT FAILURE: Do not use damaged equipment. If damage is noted, have the problem corrected before further use. 1.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Assembly Diagram 53 54 56 55 Item 61540 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
