BRAKE CALIPER WIND BACK TOOL SET Model 97456 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
Save This Manual NOTICE is used to address practices not related to personal injury. Notice Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
tion while operating pneumatic tools may result in serious personal injury. be controlled with the Trigger is dangerous and must be repaired. b. Use safety equipment. Always wear ANSI-approved safety impact goggles and NIOSH-approved dust mask/respirator. Safety equipment such as non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c.
Vibration Hazard This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: abnormal vibration occurs, stop use immediately. Specific Safety Rules 1. Maintain labels and nameplates on the Caliper Wind Brake Tool Set. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2.
Specifications Product Application Universal fit. Works with most European, Asian, and United States made vehicles. Operating Air Pressure 72 PSI to 110 PSI Air Inlet Size 1/4” - 18 NPT Fabrication Forged steel Disc Adapters. Die Cast Aluminum Gun with stamped steel and machined steel. Additional Features Rotates left or right to wind back pistons. Magnetic pad base. Trigger pressure speed control. 15 Pads.
518i, 525i, 1x, 740i, 850ci, Sri (R), Toyota® Celica, Co- M5 (F), Mercedes Benz® 190, rolla, GT, MR2 (R), VW 200, 300, 420, 560 (F), Golf Gti, Jetta, Synchro, Mitsubishi® Colt (F), Nissan® Jetta Gti, Passat CL, GL, Mlera, Stanza, Sunny (F), GT, Corrado, Scirroca, GTX. Pad 8: General Motors® most 1-7/8” Range Rover® Austin, Metro, diameter pistons. 200 & 400 Series, Maestra, Pad 9: General Motors® most 2-1/8” Montego (F), Toyota® Camry (F), Volvo® (F), VW® Passat, diameter pistons.
General Operating Instructions 1. DIRECTION HANDLE (18A) Place the proper Pad on the Sliding Bar (2A) of the tool. (See Figure C.) FIGURE C PAD TRIGGER (6A) FIGURE E SLIDING BAR (2A) 2. 3. Connect an air hose to the Air Connector (5A) of the tool. Turn on the air compressor, and set its regulator between 72 and 110 PSI. Do not exceed 110 PSI. (See Assy. Diagram.) Insert Adapter (14A) onto the caliper of the vehicle.
WARNING To prevent serious injury from accidental operation: Disconnect the tool from its compressed air supply source before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the tool.
SKU 97456 14A 29A 28A 27A 26A 25A 12A 24A 22A 11A 21A 23A 10A 9A 20A 8A 7A 2A 6A 4A 15A 1A 5A 16A 19A 13A 17A 18A 30A 3A 31A For technical questions, please call 1-800-444-3353.
Limited 1 Year warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).
