Instruction Manual

ManualsBrandsHardy ManualsScalesEnviro Bench Scales

PROVIDING SOLUTIONS IN:

Tension Control

Process Weighing

Vibration Monitoring

Local Field Service

9440 Carroll Park Dr. · Suite 150 · San Diego, CA 92121-5201· 858/278-2900 · 800/821-5831

Fax 858/278-6700 · Web www.hardyinst.com

Document Number: 0596-0320-01 Revision A

Quick Guide to Enviro Scale Setup

To enter menus press and hold Program/Enter

Press the Over/Under/Next key to scroll through selections.

1. Setup

2. Config

3. APP

4. Cal

5. Done

Press the Program/Enter key to enter the selection.

Keypad operation:

• Program/Enter key = accept displayed value. Advance to next step

• Over/under/next = scroll forward or moves flashing selection one place to right

• B/G/NET = Backs up one step in programming mode.

• UNITS = scrolls forward through choices or increments value selection.

• 1 = decrements selected digit value

• TARE = moves backwards through selection or moves flashing selection one place to

left.

• ZERO = Resets value to all zeros

• Print = moves decimal place to the right.

The parameter settings in the Setup, Config, and APP menus will determine how the unit will

operate.

Setup Menu

• Time Format for display and print out

o 12 hour format

o 24 hour format

• Set-ti - Set time (always set in 24 hour format)

• Set-da – Set date (MM.DD.YY)

• Id - unit ID (1-32)

• Port 1 (set serial port 1 output)

o Off – no serial output

o Poll – Computer polls for output

o Pollid – Computer polls for output using unit ID

o Contin – continuous output

o Button – transmit when print button pressed

Summary of content (13 pages)

PAGE 1
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service Quick Guide to Enviro Scale Setup To enter menus press and hold Program/Enter Press the Over/Under/Next key to scroll through selections. 1. Setup 2. Config 3. APP 4. Cal 5. Done Press the Program/Enter key to enter the selection. Keypad operation: • Program/Enter key = accept displayed value.
PAGE 2
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service • • • • • • • • • • • • • • • o Auto – Transmit occurs when autoprint threshold is met or exceeded o diS – continuous output using remote display format Baud – set baud rate port 1 Dbit – set data bits (7 or 8) Port 1 P – Parity setting (odd/even/none) Port 1 Busy – set handshaking (no, lo, hi) Port 1 Opti – include time on output Port 1 Opda – include date on output Port 1 Opid – include ID on output Port
PAGE 3
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service • • • • • • • • • • O.r – zero tolerance range (set as % of capacity) o 100 o 2 D – division size o 50, 20, 10, 5, 2, 1, 0.5, 0.2, 0.1, 0.05, 0.02, 0.01, 0.005, 0.002, 0.001, 0.0005, 0.0002, 0.0001 Filter – (intended to minimize effects of motion, vibration, and wind currents) Flf – Flush filter.
PAGE 4
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service • • • Aout – auto print enable when accumulate weight met. Beep – beep tone for key press C-fact - conversion factor for custom units. Will multiply weights, in primary units, to get custom units. Divide primary units by C-factor to get display in custom units. Cal Menu • SL – security level – see manual for complete setup information.
PAGE 5
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service 8. Press Program/Enter to enter the Cal menu. 1. SL – Press the Over/under/next key to set the Security Level. Enter to accept. 2. Unit flashes –dl--, then gives raw counts for deadload weight. Scale should be empty except for dead load at this time. • If the counts do not show zero, press the ZERO key to set this new cal zero point.
PAGE 6
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service Operations setup: Check weighing setup: 1. Press and hold the Over/Under/Next key until “CHEC” is displayed. 2. Press Enter to enter into the checkweigh setup menu. a. Rec 1 will display 3. Press enter to accept recipe 1 or press over/under/next key to go to next recipe and enter. 4. Display shows EnA. Press over/under/next key to toggle between Y & N to enable this recipe. Press enter to accept. 5.
PAGE 7
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service iii. The entire under and accept section leds will be lit and the first of the over section. Adjust the value displayed to be equal to the low end of the over range. Press enter to accept. iv. The entire bar graph will be lit. Adjust the displayed value to be equal to the high end of the over range. Press enter to accept. c. The display will briefly display CSaved and return to weight display. d.
PAGE 8
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service b. If selection b above (auto/manual) i. Will automatically add weight to accumulator even if out of range ii. Will require the print button pressed to send output from serial port c. If selection c above (manual/auto) i. Will require the Program/Enter button pressed to add weight to accumulator ii.
PAGE 9
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service 3. To clear accumulator a. While viewing the accumulator i. Press the ZERO key 1. Unit will display Clr Y/N a. If select Clr Y and press Program/Enter i. Unit will clear accumulator b. If select Clr N and press Program/Enter i. Unit will not clear accumulator NOTE: If you wish to change units of measure on the unit, accumulator must be cleared. Peak Hold 1. To enable Peak Hold a.
PAGE 10
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service The unit has several different outputs from the serial port based on the settings of the unit. Below are screen shots showing how each of the different setups will look. Serial port output Set up to include time, date, and ID. If one or all of these are not selected to print, the output would be the same, except without the non selected data. Data collected is shown ASCII format.
PAGE 11
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service Print accumulator with All = N Print accumulator with ALL = Y Print after each addition to accumulator 9440 Carroll Park Dr. · Suite 150 · San Diego, CA 92121-5201· 858/278-2900 · 800/821-5831 Fax 858/278-6700 · Web www.hardyinst.
PAGE 12
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service Continuous output (shows lower case gr as weight is changing and upper case GR when stable) 9440 Carroll Park Dr. · Suite 150 · San Diego, CA 92121-5201· 858/278-2900 · 800/821-5831 Fax 858/278-6700 · Web www.hardyinst.
PAGE 13
PROVIDING SOLUTIONS IN: Tension Control Process Weighing Vibration Monitoring Local Field Service Output for remote display (just outputs weight with no carriage returns or line feeds in the output string.) 9440 Carroll Park Dr. · Suite 150 · San Diego, CA 92121-5201· 858/278-2900 · 800/821-5831 Fax 858/278-6700 · Web www.hardyinst.