Manual

ManualsBrandsHardy ManualsScalesEnviro Bench Scales

Enviro™ Series

Printer Addendum

0596-0317-01 A

Hardy’s Enviro™ Series checkweighing instruments can be connected to a variety of serial printers and

remote displays via the serial communications port. Recommended printers available through 3

parties are

listed below with an explanation of how each printer connects to the Enviro™ Series instrument. See the

Hardy Instruments Website for an up-to-date listing of recommended printers.

Printers available from Fairbanks Scales................................................................................................... 1

3550 Tape Printer.................................................................................................................................. 1

TM-U295 Ticket Printer ....................................................................................................................... 2

TM-U590 Ticket Printer ....................................................................................................................... 2

Okidata 186T Form Printer................................................................................................................... 3

Okidata 420 Form Printer ..................................................................................................................... 6

Remote Display..................................................................................................................................... 8

Printers available from Fairbanks Scales

3550 Tape Printer

The Enviro™ Series should

be programmed for Port 1

Output button, 9600 baud, 8

data bits, no stop bits, and

Hibusy.

DS2 ON

OFF

DS1 ON

OFF

Enviro™ DB25 . . . . . .

0596-0317-01 Rev. A Page 1

Summary of content (8 pages)

PAGE 1
Enviro™ Series Printer Addendum 0596-0317-01 A Hardy’s Enviro™ Series checkweighing instruments can be connected to a variety of serial printers and remote displays via the serial communications port. Recommended printers available through 3rd parties are listed below with an explanation of how each printer connects to the Enviro™ Series instrument. See the Hardy Instruments Website for an up-to-date listing of recommended printers. Printers available from Fairbanks Scales...................................
PAGE 2
TM-U295 Ticket Printer The Enviro™ Series should be programmed for Port 1 Output button, 9600 baud, 8 data bits, no stop bits, and Hibusy. Set the printer’s dip switches per the following: Enviro™ DB25 1 and 3 on, the rest off. TM-U590 Ticket Printer The Enviro™ Series should be programmed for Port 1 Output button, 9600 baud, 8 data bits, no stop bits, and Hibusy Enviro™ DB25 Printer dip switch settings: DSW 1: 1, 3, and 7 on only. DSW 2: All off. 0596-0317-01 Rev.
PAGE 3
Okidata 186T Form Printer The Enviro™ Series should be programmed for Port 1 Output button, 9600 baud, 8 data bits, no stop bits, and Hibusy. To Change Menu Settings: 1. To enter MENU MODE, press and hold SELECT while turning on the printer. The “12” and “UTILITY” LEDs will blink. 2. With the printer in the Menu Mode, press SELECT to print the complete menu. The current default settings print out. It is recommended to use tractor fed paper.
PAGE 4
(group) (item) (set) (press LINE FEED to change) (press FORM FEED to change) (press TOF SET to change) Symbol Sets Code Page USA Vertical Control Vertical Control Vertical Control Line Spacing Skip Over Perforation Page Length 6 LPI No 11” Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Graphics 7 or 8 Bits Graphics Receive Buffer Size Paper Out Override Paper Registration 0 7 or 8 Bits Data Word Operator Panel Function Reset Inhibit Print Suppr
PAGE 5
Busy Line Selection SSD- Pin 11 SSD+ Pin 11 ** DTR- Pin 20 RTS- Pin 4 Switch 7, 8 (SW1) OFF, ON OFF, OFF on, on ON, OFF (Sw2) (** indicates typical Fairbanks setting) Transmission Speed Switches 1, 2, 3 (SW2) 19,200 bps ** 9,600 bps 4,800 bps 2,400 bps 1,200 bps 600 bps 300 bps 110 bps ON, ON, ON off, on, on ON, OFF, ON OFF, OFF, ON ON, ON, OFF OFF, ON, OFF ON, OFF, OFF OFF, OFF, OFF DSR Input Signal Active ** Inactive Switch 4 (SW2) ON off Buffer Threshold 32 bytes ** 256 bytes Switch 5 (SW2) ON o
PAGE 6
Okidata 420 Form Printer The Enviro™ Series should be programmed for Port 1 Output button, 9600 baud, 8 data bits, no stop bits, and Hibusy. To change Menu Settings: SEL SEL MENU SHIFT EXIT POWER LF FF/LOAD Micro Feed Down Micro Feed Up GROUP ITEM PARK TEAR QUIET TOF PRINT SET MENU ALARM 1. To enter MENU MODE, press and hold the SHIFT key while pressing the SELECT key. The “MENU” legend will be illuminated while in the menu mode. 2.
PAGE 7
(group) (item) (set) (press LINE FEED to change) (press FORM FEED to change) (press TOF SET to change) Rear Feed Rear Feed Skip Over Perforation Page Length No 11” Bottom Feed Bottom Feed Bottom Feed Bottom Feed Line Spacing Form Tear-off Skip Over Perforation Page Length 6 LPI Off No 11” Top Feed Top Feed Top Feed Top Feed Line Spacing Form Tear-off Skip Over Perforation Page Length 6 LPI Off No 11” Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Set-Up Se
PAGE 8
Remote Display The Enviro™ Series can be connected to a 1600 Series remote display using Port 1. The Enviro™ Series should be programmed for Port 1 Output dis, 2400 baud, 7 data bits, 1 stop bits, and nobusy. Enviro™ Series tb1 3 TX 5 Gnd Note: RS232 communications are limited to a length of 50 cable feet. 0596-0317-01 Rev.