Owner's manual

Index
Index
Symbols
—/Test/Clr 5-2
Numerics
14 AWG power line 3-9
2/Status/Bar 5-2
240 VAC 50/60 Hz Input Voltage (-E2) 1-7
3-pin terminal block connector 3-9
4 connector pin description 3-10
5 AMP, 250 VAC Slow-Blow 3AG, 3-9
5 volts DC Excitation Voltage 8-31
A
Allen Bradley Remote I/O 1-2
Allen-Bradley Remote I/O Installation and Operation
Manual (P/N 0596-0173)
7-22
Allen-Bradley Remote I/O Interface (-B8) 2-7
Allen-Bradley Remote I/O Option -B8 5-14, 7-22
Allen-Bradley RIO Interface Option -B8 3-20
analog card 4-4
Analog Card Adjustment 4-5
Analog Output (-B1) 1-5, 2-6
Analog Output Menu Setup Procedures 5-13
Analog Output Option -B1 (See Fig. 3-12) 3-16, 4-4
Analog Output Setup Procedures (Option) 5-12
analog transmitter 4-4
Approvals 2-5
Auto Zero Tolerancing Configuration Procedures 4-8
Auto Zero Tracking 1-4
averaged gross 4-8
Averages 2-1
B
B1 Option Connector Wiring 3-16
bar graph parameters 5-6
Bar Graph Setup Procedures 5-6
Base Graduation Number 6-8
base motion number 6-8
Baud rate selection 5-9
Baud rates 1-4
BCD Menu Setup Procedures 5-7
BCD option board 5-7
BCD Option Board Installation -B2, -B5, -B9 3-17
BCD Print 5-7, 7-20
BCD Quad Termination Board (-B7) 2-7
BCD Quad Termination Card (-B7) 1-5
BCD Single Termination Board (-B6) 2-7
BCD Single Termination Card (-B6) 1-5
BCD sub-menu 7-20
BCD terminal board 3-20
BCD Termination Board Installation Procedures (See
Fig. 3-14)
3-19
BCD Terminator Boards - B6, - B7 3-19
Before Clearing Memory. 6-19
Bi-Directional Communications 2-5
Bi-directional Communications 7-7
bi-directional communications 1-6
Bi-directional serial ports 4-1
Binary Coded Decimal (BCD) 2-8
Binary Coded Decimal (BCD) Output 1-5
Binding on the Load Cell 6-1
Blind Remote Mount HI 2151/30WC-BR 2-4
C
C2 Load Cell Connections (J1) (See Fig. 3-9) 3-13
C2 weighing system 1-2
C2® Calibration 1-2
C2® Second Generation Calibration Procedures 6-12
C2™ Calibration (C2 CAL) 6-11
Cable Pinouts 3-17
cable runs 3-8
Cable Type 7-8
Cabling and Interconnecting 3-8
CAL button 4-7
CAL menu 4-7
Calibration Configuration without Security Code 4-7
Calibration Menu 5-14
Calibration Procedures 6-11
Calibration Results form 6-15
Calibration Setup Procedures 6-6
Case Dimensions 2-3
change values 7-2
Checking for Mechanical Problems 6-14
clean" primary line 3-9
Clear Controller Memory 6-19
Clear to Send (CTS) 5-10
Cockpit Configuration Assistant 2-9
Combination Status Indicator/Bar-Graph LEDs 6-4
Command Meaning 7-13
command strings 7-11
Common Mode Rejection 2-2
Common Mode Voltage Range 2-2
communications ports 1-4
compact 1-1
complete hardware groups 8-1
config dip CAL switch 4-7
Configuring Lock S3-7 4-10
Configuring Multidrop S3-1 4-9
Configuring Option S3-4 4-9
Configuring Peak Hold Mode 4-8
Configuring Serial S3-3 4-9
Configuring Set Point S3-5 4-9
Configuring the Power & Relay Board Dip Switches S2
(See Fig. 4-12)
4-10
Conversion Rate 2-1
Current 4-5
cut off frequencies 1-2