Owner's manual

HI 2151/30WC MANUAL
D
D2 option card 3-11
Data Formats 7-10
Data Formats - Binary Representation 7-10
Data Formats - Weight Data Format 7-10
data/status lines 3-20
DDE Installation and Operation Manual, document
number 0596-0221
3-22
Dead Band Limits 7-4
Dead Band Sub-Menu 7-6
dead band value 7-4
deadband 1-4
default auto zero tolerance 6-9
Digital Volt Meter (D.V.M) 8-34
Digital Volt Meter (DVM) 1-3
Digital Voltmeter 2-2
Dimensions of the enclosure cutout 3-3
Dip Switch Locations (See Fig. 4-10) 4-7/8
Dip Switch Setting 4-8
Dip Switches S2 4-9
Disassembling the rear panel and setting jumpers 4-4
Disassembly and Reassembly Notes and Cautions 8-1
Display 2-1
Display Increments (Graduations) 2-1
DO NOT CUT THE CABLE!!! 6-16
Document Number 0596-0173 3-20
Dynamic Data Exchange (DDE) (-B14) 1-6
Dynamic Data Exchange (DDE) I/O Server -B14 3-22
E
E2 3-9
Earth Ground Cable Shield 7-8
Echo 5-10
Electrical Check Procedures 6-2
Electrical Installation 3-8
Electrostatic Discharge (ESD) 3-3
End Calibration 6-14
Enter 5-4
Entering Dead Band Tolerance Procedures 7-6
Entering Preact Values Procedures 7-6
Entering Set Point Procedures 7-6
Entering Set Points 7-5
Environmental Requirements 2-2
ERR 8 4-7
Error Messages and Definitions 8-37
Excitation Monitor 1-3, 2-2
Excitation Monitor (Current) Setup Menu 8-34
Excitation Voltage 2-1
External Setpoint Relays Card (-D2) 1-6
External Setpoint Relays Card (-D3) 1-7
F
Firmware 3-10
Formats the serial data output 5-9
Fourteen Segment Display 6-4
Frequency 2-2
Front Panel Dimensions 2-3
Front Panel Setup Procedures 4-5
full analog output 5-12
full scale mV/V output 6-15
full weight capacity 6-3
G
gasket 3-5
Gross Mode 1-2
H
Hard Calibration (HD CAL) 6-11 to 6-15
Hardy Link LAN 1-4
Hardy Link Local Area Network (LAN) 1-4
Hardy Link software option 4-9
Hexadecimal number 7-17
HI 215IT Series Junction Boxes 3-22
HI 215T series junction box 8-4
Highest gross 4-8
host computer control 7-7
Humidity Range 2-2
I
individual set point 1-4
in-flight" compensation value 7-5
Input 2-1
Input Power Wiring 3-9
Install the Front Panel. 3-5
Installation Details 3-23
Installation of the Instrument Enclosure 3-6
Installation of the Secure Memory Module 3-24
Installing the HI 2151/30 Remote Mount Model 3-5
Installing the HI 2151/30 Wall Mount Model 3-7
Installing the HI 2151/30WC in a Panel 3-3
Installing the Blind Remote Model 3-7
INTEGRATED TECHNICIAN (IT®) 6-18
INTEGRATED TECHNICIAN™ (IT®) 1-1
IT ® 1-2
IT Junction Box 8-31
IT junction box 1-3
IT® Junction Box HI 215IT-FG Series 2-5
IT® Junction Box HI 215IT-SS or PS Series 2-4
J
J3 Serial Port Wiring 3-11
jumper error 5-6
Jumper Location. (See Fig. 4-7) 4-6
Jumper Settings (See Fig. 4-8) 4-7
jumpers and dip switches 4-1
K
Key Pad 2-1
Keypad Functions (See Fig. 5-1) 5-1