Owner's manual
Index
L
Linear Correction 6-14
live load 6-13
Load Cell Count 6-12
Load cell/point 3-12
Load Cell/Point Connections (J1) 3-12
Load Cell/Sensor/Point 8-30
Load Check 6-6
Logic Controllers 1-5
logical choice 7-2
M
material impacting 6-10
Maximum Zero Tolerance 2-1
Mechanical Check Procedures 6-1
Mechanical Installation 3-2
mechanical noise 1-2
Miscellaneous Options 1-7
Mode 5-1
mode key 5-1
Model Code Breakdown 1-7
MONITOR subcommand 7-17
Motion Tolerance 6-8
Multidrop function 4-9
multipurpose 1-1
N
National Institute of Standards and Technology (NIST)
1-7
Negative Pulse 4-7
NEMA 4 or 4X conduit fittings 3-7
NEMA Ratings 2-4
Net 1-2
NIST/NTEP Certification Mode Kit (-E3 except for -F4
wall mount)
1-7
No Keypad Operation 8-31
Non C2 Load Cell Connections (J1) 3-14
Non-Linearity 2-1
ntrinsic Barrier Assembly (-F1, -F3 thru -F7) 1-7
numeric keypad 7-2
numeric keys 6-16
O
Operating Procedures 7-19
Operating Temperature Range 2-2
Option Board 3-15
Option Boards 7-3
option connector pins 3-16
Option Menu 7-19
Option Menus and Option Parameters 7-3
Optional Equipment 2-6
Optional Modes 7-1
Optional Relays or TTL Level Outputs 3-10
Options button 5-6
Options Cabling and Interconnect 3-16
Ordering Replacement Parts 8-40
original voltage reading 1-3
Output Device Options 1-5
OUTPUT DISABLE 7-20
Output Disable 7-20
OUTPUT OPTION BOARD INSTALLATION PROCE-
DURES
3-15
Output Setpoint Relay Wiring 3-10
Overview of Typical Load Cell System 8-30
P
Panel Cutout Dimensions 2-3
Panel Cutout Specifications 3-3
Panel Mount (Model # HI 2151/30WC) 2-2
Panel Mount Instrument 1-7
Parallel BCD Board Connector to DB Connector 3-17
Parallel BCD Board Print Configuration Procedures -
B2, -B5, -B9
4-6
Parallel BCD Communication 7-19
Parity selection 5-9
Peak Hold 1-2, 7-3
Peak Hold (-C1) 1-6, 2-8
Peak Hold Mode 7-1, 7-21
Perform the Hard Calibration Self Test 6-15
Performing the Self Test 6-17
phillips screw driver 3-5
Physical Characteristics 2-2
Portable Display and Keypad (-E4) 1-7
Portable Display HI 2151/30XX-E4 (use with HI 2151/
30WC-BR)
2-4
positive dead band 7-5
Positive Pulse 4-7
Power 2-2
preact 1-4
Preact Limits (See Fig. 7-3) 7-5
preact value 7-5
Pre-Calibration Procedures 6-1
Print 5-2
Procedures to Restore Calibration Parameters 6-19
Process Weighing Function Buttons 7-1
Profibus I/O Interface (-B12) 2-8
Profibus Installation and Operation Manual (Prt. # 0596-
0211)
7-22
Profibus Interface Card Option Wiring Diagram 3-24
PROFIBUS Interface Option (-B12) 1-6
Profibus Interface Option -B12 3-21, 7-22
Programmable Logic Controller 4-5
Q
Quick C2® Calibration Procedures 6-18
R
Rate of Change (ROC) 7-20
Rate of Change (ROC) (-C2) 2-8
Rate-of-Change (ROC) 1-2
Rate-of-Change (ROC) (-C2) 1-6
Rate-Of-Change Mode 7-2