Owner's manual

HI 2151/30WC MANUAL
readings per average 6-10
Rear panel input 1-4
Reassembling Rear Panel 4-5
re-calibrated periodically 6-1
Recommended Installation Procedures 3-8
Register 7-20
Remote Functions 1-4
Remote Functions Non-operational 8-31
Remote Functions Wiring 3-12
Remote I/O (RIO) Interface to the Allen-Bradley Net-
work (-B8)
1-5
Remote Mount Model HI 2151/30WC-RM 2-3
Report any damage 3-1
Request to Send (RTS) lines 5-10
Resolution 2-1, 4-10
Return to Zero Test 1-3, 8-35
ribbon cables 3-19
ROC data 7-20
ROC LED 5-13
Route wiring types 3-8
RS 232 1-4
RS 422 1-4
RS 422/485 ports 4-3
RS 485 1-4
RS-232C 7-7
RS-232C, RS 422/485 Bi-directional Serial Port 5-5
RS-422/485 7-7
RS-422/485 Configuration Wiring 7-8
RS-422/485 Electrical Specifications 7-9
RS-422/485 Wiring and Electrical Specifications 7-8
S
Secure Memory Module (SMM) 1-3
Selecting the Hard Calibration Sub-Menu 6-13
Selecting the Soft Calibration Sub-Menu 6-16
Self-Test 8-25
self-test program 8-25
sequential tests 8-25
Serial Commands 7-11
Serial Commands - Data Transmission Format 7-11
Serial Commands, Command Set 7-12
serial communication parameters 7-11
Serial Communications 2-5, 7-7
Serial Connector 7-8
Serial Port 1-4
Serial port configuration 5-9
Serial Port Menu Setup Procedure (See Chapter 4 for
Configuration Procedures)
5-9
Serial Procedures 5-10
Serial Protocol - Multidrop Mode 7-9
Set Point Limits 7-4
Set Point Options 1-6
Set Point Relay Option Board Installation -D2 3-22
Set Point S3-6 4-9
Set PointRelays 1-4
Set Points 7-4
Set Up for Profibus Interface Card Option -B12 5-14
Signal Grounds 7-8
Six External Solid State, Set Point Relays (-D2 & -D3)
2-9
Six TTL Level Outputs (-D1) 2-9
Six-wire, shielded load cell/point cable 3-13
sliding average 6-10
SMM 1-3
socket 3-16
Soft Calibration (S CAL) 6-11
Soft Calibration Procedures for Single Load Cell/Point
Systems
6-15
Soft Calibration Self Test Process 6-17
solenoid 8-32
special test equipment 8-30
standard RS-232C/422/485 serial port 7-9
Standard RS-232C/RS422/485 Configuration 4-1
Standard Setpoint Relays 2-1
Standard SPDT (Form C) Relays 3-10
standoffs 3-23
Status/Bar button 6-5
Stop bit selection 5-9
Storage Temperature Range 2-2
strain gauge based force transducer 8-30
switch eight of S3 1-4
System Configuration 4-1
System Integrity Check and Fault Determination 8-25
System Support 8-39
T
Tare 5-1
Tare button 5-1
Tare Value 5-1
target weight or level 7-4
Temperature Coefficient 2-2
The Calibration Menu 6-6
The Full Scale Count Sub-Menu 6-20
The Return (RETURN) Display 6-14
Three General Rules for Setpoints 7-5
toggle switch (#2) 4-8
Total (-C6) 7-2
Total Option 7-21
TOTAL Setup Procedures 5-14
Totalized 1-2
Totalizer (-C3) 2-9
Totalizer Mode 7-21
Transmission speed 7-7
Trouble Shooting Using Integrated Technician. 8-2
TTL level outputs 3-10
TTL(Transistor - Transistor Logic) Level Output (-D1) 1-
6
two main operating menus - Set Point and Option 7-2
U
Unpacking 3-1
user-selectable 7-7
Using Solid State Relays with Light Loads (Optional Set