User Manual

ManualsBrandsHardy ManualsToolsHI 4050CW Check Weighing Bundle

QUICK INSTALLATION GUIDE

MECHANICAL INSTALLATION

Insta lli ng the HI 4050 Weight Controller in a Panel

FIG. 1 PANEL HOLE DIMENSIONS

FIG. 2 PANEL HOLE DIMENSIONS (RETROFIT)

Step 1. Make sure that all Electrostatic Discharge (ESD) precautions

are take n before an d during installation.

Step 2. Use the provided template to make the hole pattern in the

panel door or cover. (Part # 0578 -0071-01)

FIG. 3 PANEL MOUNT INSTALLATION

Step 3. Use a phillips head screwdriver and instal l th e five (5) 6-32 x

1/2 inch screws that fasten the bezel to the panel. (See Fig. 3)

Use a torque screw dri ver and torque each screw to 10 inch/

pounds. DO NOT OVERTIGHTEN!

Step 4. Thread the four (4) threaded rods through the approp ri ate

holes in the panel and into the bezel. For the retrofit you don’t

have to place the rods through the holes. (See Fig. 4)

Step 5. Hand tighten each rod until you can no longer turn the rod. Do

not for ce the rods or use pliers of any kind.

Step 6. Put th e Display cabl e and connector through the 1.25-inch

hole in the panel door or cover and plug the display connector

into the di splay header in t he bezel. (See Fig. 3)

Step 7. Gently slide the electronic encl osure onto the t hreaded rods

while making sure the display cable glides easily into the

enclosure and does not kink. Move the electronic enclosure

toward the panel until it stops. (See Fig. 3)

Step 8. Thread the four (4) 6-32 thumb screws onto the threaded rods

until tight. Do not use pliers on the thumb screws.

FIG. 4 RETROFIT PANEL MOUNT INSTALL FOR HI 2151/30 &

HI 2110

DIN Rail Installation HI 4050 Weight Controller

Step 1. Snap the DIN rail mounting feet into any of the two holes on

the front panel of the electroni c enclosure. (See F i gs. 5 & 6)

FIG. 5 DIN RAIL MOUNTING FOOT

3.100

.172 THRU, 9 PL

4.05

3.200

3.000

2.590

1.274

.41

.205

.44

1. 25 THR U

.475

.755

5.250

6.200

7.08

INSTRUMENT

BEZEL OUTLI NE

7.08

6.200

.225

.44

.045

.41

4.05

3.200

3.000

3.100

.172 THRU, 9 PL

INSTRUMENT

BEZEL OUTLI NE

3.090 .060

5.750 .060

CUTO UT

Display

Connector

Summary of content (3 pages)

PAGE 1
QUICK INSTALLATION GUIDE Step 3. MECHANICAL INSTALLATION Installing the HI 4050 Weight Controller in a Panel Step 4. .172 THRU, 9 PL 3.100 Step 5. 1.25 THRU 4.05 3.200 3.000 2.590 1.274 INSTRUMENT BEZEL OUTLINE Step 6. Step 7. .205 .41 .475 .755 5.250 6.200 .44 Step 8. 7.08 Use a phillips head screwdriver and install the five (5) 6-32 x 1/2 inch screws that fasten the bezel to the panel. (See Fig. 3) Use a torque screw driver and torque each screw to 10 inch/ pounds.
PAGE 2
V+ CAN+ Shield V- CAN- FIG. 8 C2® Load Point Connection Cable color code for C2 Load Points (left to right facing the rear panel): • • • • • • • • • FIG. 6 VERTICAL AND HORIZONTAL ORIENTATION Step 2. Step 3. NOTE: Step 4. Step 5. NOTE: When installing firmly push the mounting feet until you hear a snapping sound. The snap means they are mounted correctly. After installation give each mounting foot a little tug to make sure they are seated correctly.
PAGE 3
INPUT POWER WIRING STARTING THE HI 4050 WARNING: DO NOT PLUG THE POWER CONNECTOR INTO THE HEADER WITH LIVE POWER. TO DO SO WILL RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY. Step 1. Step 2. WARNING: Connect the power connector (AC or DC) to the HI 4050. The Instrument boots up to the Summary Display. (See Fig. 9) IF A LITHIUM BATTERY IS REPLACED WITH AN INCORRECT TYPE IT MAY CAUSE AN EXPLOSION WHICH WILL CAUSE PROPERTY DAMAGE OR PERSONAL INJURY.