Getting Started
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • info@thomann.de DocID: 521039_23.08.2022
Spaceship PowerBar 80
For the transport and protective packaging, environmentally friendly materials
have been chosen that can be supplied to normal recycling. Ensure that plastic
bags, packaging, etc. are properly disposed of. Do not just dispose of these ma-
terials with your normal household waste, but make sure that they are collected
for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equip-
ment Directive (WEEE) in its currently valid version. Do not dispose of your old
device with your normal household waste. Dispose of this product through an
approved waste disposal rm or through your local waste facility. Comply with
the rules and regulations that apply in your country. If in doubt, consult your
local waste disposal facility.
EN
Using the product
1. Connect the device to the mains using the supplied power cord to put the
device into operation.
2. Use a suitable voltage supply cable to connect eect pedals or similar devices
which require 24V
supply voltage at a maximum of 2000mA to the out-
put1.
3. Use a suitable voltage supply cable to connect devices with high power
consumption (i.e. multi-eect devices) which require 9V
supply voltage at
a maximum of 3000mA to the output2.
4. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 9V
supply voltage at a maximum of 100mA to the out-
puts36.
5. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 9V
supply voltage at a maximum of 250mA to the out-
puts710.
6. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 9V
supply voltage at a maximum of 500mA to the
outputs1113.
Danger of property damage by polarity reversal
Make sure that the polarity of the devices to be connected must be
the same as the polarity of the power supply outputs (
). To
power a device with polarity-reversed voltage may damage it!
7. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 9V
,12V or 18V supply voltage at a maximum of
500 mA, 375 mA or 250 mA to the outputs14-17. Set the associated switch
above the output to the position of the required voltage. The maximum output
power of 48.6 W must not be exceeded.
8. Use suitable voltage supply cables to connect devices as smartphones or
tablets to the USB outputs.
9. Each operational output 1-17 is indicated by a green LED. If an output is
switched o due to overload, the LED turns o. Then disconnect the pedal in
question from the device. After approx. 2 seconds, the normal voltage supply is
restored here.
10. To switch o the device, disconnect the power cord from the mains.
Danger of property damage by overvoltage
Make sure that connected devices are actually suitable for the set
voltage. To power a device with overvoltage may damage it!
Technical specications
• Connections ( )
- Output 1 24V @ max. 2000mA
- Output 2 9V @ max. 3000 mA
- Outputs 3-6 9V @ max. 100 mA (individually insulated)
- Outputs 7-10 9V @ max. 250 mA (individually insulated)
- Outputs 11-13 9V @ max. 500 mA (individually insulated)
- Outputs 14-17 switchable 9/12/18V @ max. 500/375/250mA
(individually insulated)
• USB output USB-C max. 18 W
USB-A max. 18 W
• Power output 48.6 W
• Current output 4050 mA
• Supply voltage 100 - 240 V ~ 50/60 Hz
• Dimensions (W×H×D) 800 mm×30 mm×50mm
• Weight 0.97kg
• Ambient conditions Temperature range 0 °C...40°C
Relative humidity 20 %...80 %
(non condensing)