Manual

Programming the Remote
Macro Programming • PresstheVID3 Input Selector Button
Macrosenableyouto easilyrepeatfrequently _ to indicatethe nextcommandisto be
usedcombinationsof commandswith the press transmittedto the cablebox.
of a singlebutton ontheAVR220 remotecon- • Pressthe Mute Button _ to storethe
trol. Once3rogrammed,a macrowill sendout CablePowerOncommand.
upto 19different remotecodesina 3redeter- • Pressthe Sleep Button _ to complete
minedsequentialorder,enablingyouto auto- the processandstorethe macrosequence.
matethe processof turning onyour system,
changingdevices,or othercommontasks.The After followingthese steps,eachtime you
AVR220 remotecanstoreupto five separate pressthe Macro 1 Button _), the
macrocommandsequences:onethat is remotewill sendthe PowerOn/Offcom-
associatedwith the Power On Button _), mandto the AVR220, the televisionand
andfour morethat areaccessedbypressingthe the cableboxwith a singlebutton press.
Macro ButtonsI_),
ErasingMacro Commands
1. Pressthe Mute Button _ and the Toerasethe commandsthat havebeenpro-
Macro Button _ to beprogrammedor grammedintooneof the Macrobuttons,follow
the Power On Button _]P at the same thesesteps:
time. Notethat the last Input Selector
pressedwill light red, andthe 1. Pressthe Mute Button _ and the
Program/SPLIndicator _ will flash Macro Button _ that containsthe
amber, commandsyouwishto erase.
2. Enterthe stepsfor the macrosequenceby
pressingthe button for the actualcommand
step.Although the macromaycontainupto
19steps,eachbutton press,includingthose
usedto changedevices,countsasa step.
TheProgram/SPLIndicator _ will flash
greento confirmeachbutton pressasyou
entercommands.
2. Note that the Program/SPL Indicator
will flash amber, and the LED under the
AVR Selector ql_ will turn red
3. Within ten seconds,pressthe Surround
Mode Selector/ChannelDown
Button li_).
4. Thered _EDunderthe AVRSelector
NOTE:Whileenteringcommandsfor Power
On/Offof any deviceduringa macrosequence,
pressthe Mute Button I_. DONOTpressthe
actualPowerButton.
3. When a the steps have been entered,
press the Sleep Button _ to enter the
wi go out, and the Program/SPL
Indicator _ will turn green and flash
three times before it goes out
5.Whenthe Program/SPLIndicator
goesout, the Macrohasbeenerased.
commands.The "ed light underthe Input Programmed DeviceFunctions
Selectorsql_P_ will blink and then
turn off.
Example: To program the Macro 1 Button
so that it turns on the AVR 220, TV and
a Cable Box, follow these steps:
Oncethe AVR220'sremotehasbeenpro-
grammedfor the codesofotherdevices,press
the appropriateInput Selector _ to change
the remotefromcontrollingtheAVR220 to con-
trollingtheadditionalproduct.Whenyoupress
anyoneof theselectors,it will brieflyflash in red
* Pressthe Macro 1 _ and Mute _ to indicate that you have changed the device
buttons at the same time and then release
them.
• Note that the Program/SPL Indicator
will flash amber.
• Pressthe AVR Selector _11.
• Pressthe Mute Button _ to store the
AVR 220's Power On command.
being controlled.
Whenoperatinga deviceotherthan the
AVR220, the controlsmaynot correspond
exactlyto the functionprintedonthe remote
orbutton. Somecommands,suchas theVolume
Control,arethe sameastheyarewith the
• Pressthe VID2 Input SelectorButton AVR220. Otherbuttonswill changetheir
to indicatethe nextcommandisto be functionsothat they correspondto a secondary
transmittedto theTV. labelonthe remote.Forexample,the Sleep
• Pressthe Mute Button _ to storethe and Surroundmodeselectorbuttonsalsofunc-
TVPowerOnCommanc tion asthe ChannelUpandChannelDown
Thediagrambelowshowsthe button numbers
usedin the FunctionListon 3ages37and 38.
/
harman/kardon
34 PROGRAMMING THEREMOTE