ENCHANT 1300 ENCHANT 800 ENCHANT SUBWOOFER OWNER’S MANUAL
/ IMPORTANT SAFETY INSTRUCTIONS Verify Line Voltage Before Use The Enchant soundbars have been designed for use with 100240 volt, 50/60 Hz AC current. Connection to a line voltage other than that for which your product is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model or about the line voltage in your area, contact your selling dealer before plugging the unit in to a wall outlet.
/ TABLE OF CONTENTS /IMPORTANT SAFETY INSTRUCTIONS.............................................. 2 /INTRODUCTION ........................................................................................ 4 /WHAT’S IN THE BOX................................................................................ 5 /PRODUCT OVERVIEW..............................................................................7 /INSTALLATION...........................................................................................
/ INTRODUCTION This manual includes information of the Enchant 1300, Enchant 800 and Enchant Subwoofer. We encourage you to take a few minutes to read this manual, which describes the products and includes step-by-step instructions to help you set up and get started. Read and understand all the safety instructions before using your product. This product may have an important software update available.
/ WHAT’S IN THE BOX Carefully unpack the box and check if the following parts are included. If any part is damaged, do not use it, contact your Harman Kardon retailer or customer service. ENCHANT 1300 / ENCHANT 800 1 VOL 2 3 4 5 6 7 1. Main unit 2. Power cord* 3. HDMI cable 4. AUX cable 5. Optical cable 6. Remote control (with 2 AAA batteries) 7. Wall-mount brackets * Power cord quantity and plug type vary by regions.
/ W H AT ’ S I N T H E B OX Inserting Batteries before using the Remote Control (AAA batteries X 2) Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AAA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position. ENCHANT SUBWOOFER (Optional) 1 2 1. Main unit 2. Power cord* * Power cord quantity and plug type vary by regions.
/ PRODUCT OVERVIEW Front Panel & Top Panel of the Soundbar 1 2 4 3 1. + / - (Volume) • Adjust the volume level. • Press both simultaneously to mute the soundbar. 2. (Power) • Turn the power on or to standby. • Press and hold for 5 seconds to reset the soundbar Wi-Fi settings. 3. Display panel • Display the current mode and status.
(Source) • Select the source input mode: Source Input Mode Display HDMI OUT (TV ARC) TV ARC HDMI 1 input HDMI 1 HDMI 2 input* HDMI 2 HDMI 3 input* HDMI 3 Optical input OPT Aux input AUX Bluetooth input BT USB input USB / PRODUCT OVERVIEW 4. * HDMI 2 and HDMI 3 are available on the Enchant 1300 only.
/ PRODUCT OVERVIEW Back Panel of the Soundbar ENCHANT 1300 1 2 3 4 5 6 7 ENCHANT 1300 1 2 5 7 6 3 4 1. AC IN • Connect to the power cord, then connect the power cord to a wall outlet. 2. AUX IN • Connect to the Analog output of an external audio device. 3. USB • Connect to a USB storage device to play music.
/ PRODUCT OVERVIEW 4. OPTICAL • Connect to the optical audio output on your TV or digital device. 5. SUBWOOFER PAIRING • Press to enter the subwoofer pairing mode. • Press and hold to disconnect and re-enter the subwoofer pairing mode. 6. HDMI 1 / HDMI 2* / HDMI 3* • Input digital video and audio signals simultaneously using an HDMI cable. • Connect to the HDMI output on a digital device. 7. HDMI OUT (TV ARC) • Connect to the HDMI (ARC) input on your TV.
/ PRODUCT OVERVIEW Back Panel of the Subwoofer 1 2 1. PAIRING • Press to pair the subwoofer with the Enchant soundbar. 2. AC IN • Connect to the power cord, then connect the power cord to a wall outlet.
1 2 2. DIM LEVEL • Set the brightness of the display panel. 3. PRESETS • Recall preset audio settings and SOUND MODE. To save a preset: • Press the SOURCE button to select a source. 14 4 6 (Power) • Power on or switch to standby. 15 3 5 1. • Press the SOUND MODE button to select a preferred setting for that source. VOL 13 • Adjust the VOLUME, BASS and NIGHT MODE to your preference.
SOUND MODE • Select preset sound modes to suit your music or video: STANDARD / MUSIC / MOVIE / VOICE / PERSONAL. • Select the STANDARD mode to enjoy the original sound with MultiBeam Surround Sound. • Select the MUSIC mode to enjoy music sound with a light MultiBeam Surround Sound effect. • Select the MOVIE mode to enjoy movie sound with MultiBeam Surround Sound. • Select the VOICE mode to enhance dialogue with a light MultiBeam Surround Sound effect.
/ PRODUCT OVERVIEW 15. CALIBRATION • Press and hold for 3 seconds to initiate Automatic MultiBeam Calibration. (see calibration section) * HDMI 2 and HDMI 3 are available on the Enchant 1300 only.
/ INSTALLATION Place the Soundbar below your TV on the Table NOTES: • • • Remove any interference from both sides of the soundbar so the side-firing speakers can operate correctly and reflect sound in your room. Blocking the side horns affects acoustic performance. To avoid wireless interference, keep other wireless devices 1-3 ft (0.3-0.9 m) away from the soundbar. Make sure there is an AC outlet nearby. Place the soundbar on its rubber feet on a stable and level surface below your TV.
/ I N S TA L L AT I O N Wall-mount the Soundbar CAUTION: • • • • • • Before mounting on a wall, make sure the wall can support the weight of this unit. Install on a vertical wall only. For the wall-mounting, avoid a location with high temperature or humidity. Connect cables from the unit to external devices before installing on the wall. Make sure the unit is powered off and unplugged before the installation. Otherwise, it may cause an electric shock.
/ I N S TA L L AT I O N 2) Use an appropriately sized drill bit, drill a hole in the wall at each marking. Using the appropriate anchors, screw the wall mount brackets into the support screw holes in the wall. x3 CAUTION: • If the markings do not correspond to the positions of studs, make sure to insert appropriate anchors or mollies into the holes before inserting the support screws. If you use anchors or mollies, make sure the holes you drill are large enough for the anchors or mollies you use.
/ I N S TA L L AT I O N 4) Hook the soundbar to the brackets attached to the wall. TV CAUTION: • • Do not connect the power cord of the soundbar or your TV to a wall outlet until all connections between components are complete. Before moving or installing the unit, make sure to power off and unplug first.
/ CONNECTING TO YOUR TV NOTES: • • If you want to enjoy sound only from the soundbar, make sure to set your TV audio settings to support external speakers and disable the built-in TV speakers. Before you make or change any connections, make sure that all devices are disconnected from the power outlet. Connect to your TV with an HDMI Cable (Preferred) 1) Connect the supplied HDMI cable from the HDMI OUT (TV ARC) connector on the back of the soundbar to the HDMI IN (ARC) connector on your TV.
• • • • An HDMI connection supports digital audio and video with a single connector. It is the best option to connect to your soundbar. If your TV features an HDMI ARC connector, you can hear the TV audio through your soundbar by using a single HDMI cable. This HDMI connection is required if you intend to connect other video devices to the soundbar inputs to display on your TV. On your TV, turn on HDMI-CEC operations.
/ CONNECTING TO OTHER DEVICES HDMI Cable (Preferred) Connect a digital device such as a set-top box, DVD/Blu-ray player, or games console to your soundbar through a single HDMI connection. 1) Connect the HDMI cable from the HDMI IN jack on the back of the soundbar to the HDMI OUT jack on your digital device. ENCHANT 1300 ENCHANT 800 HDMI OUT HDMI 1 HDMI 2 HDMI 3 2) Press the button on the top panel of the soundbar or the SOURCE button on the remote control to select the HDMI mode.
1) Connect the OPTICAL or AUX connector on the soundbar to the OPTICAL OUT or AUDIO OUT jack of the source device by using the provided optical cable or 3.5mm audio cable. / CONNECTING TO OTHER DE VICES Optical or Analog Audio Cables ENCHANT 1300 ENCHANT 800 AUX-IN OPTICAL IN AUX-OUT OPTICAL OUT 2) Press the button on the top panel of the soundbar or the SOURCE button on the remote control to select the OPTICAL or AUX mode.
/ CONNECTING TO POWER Power On the Soundbar NOTES: • • • • Before connecting the power cord, make sure all other connections have been completed. The (Power) button will begin working in 4 to 6 seconds after plugging in the AC power cord. When you disconnect the power cord, always pull the plug, never the cable. Do not connect this unit or other components to an AC outlet until all connections between components are complete.
/ CONNECTING TO POWER 2) Plug the other end of the power cord into a live AC (mains) wall socket. • “LOADING” scrolls on the display panel. The soundbar will take about 30 seconds to load, then enter standby mode and ready for use. 3) Slide the battery compartment cover until it is completely removed. Insert the two provided AAA 1.5V batteries with correct polarity orientation. Slide the cover back into position. 4) Press (Power) to power on the soundbar. • “ON” is displayed.
1) Power on both the soundbar and the subwoofer. 2) Press the SUBWOOFER PAIRING button on the soundbar or PAIRING button on the subwoofer to enter pairing mode. • “SUB PAIRING” will be displayed. You will hear a pairing chime once connected and “SUB PAIRED” will be displayed.
• • • If the soundbar is powered off, the subwoofer will enter standby mode. If you use a device that uses the same frequency (2.4GHz) as the soundbar near your soundbar, interference may cause some sound interruption. The maximum transmission distance of the wireless signal between the soundbar and the subwoofer may vary depending on your operating environment.
/ CONNECTING TO WI-FI The soundbar is connected to Wi-Fi with the Google Home app. 1) Download the Google Home app. 2) Power on the soundbar. 3) Open the Google Home app and set up your soundbar as instructed in the app. Always follow the instructions in the app to complete the Wi-Fi setup. 4) Sign in with your Google account. If you do not have, create a new one.
/ USING YOUR SOUNDBAR Play Music with Google Cast With Chromecast built into your Enchant soundbar, you can stream music, podcasts, and playlists from 300+ music apps to your soundbar by simply tapping the Cast button. 1) Open any Chromecast-compatible app on your smartphone or tablet. 2) Tap the icon on the app and select the Enchant soundbar. 3) Press “Play” on the app. NOTES: • • • The name of your soundbar is assigned during the Wi-Fi setup.
/ USING YOUR SOUNDBAR 2) Choose “HK ENCHANT 1300/800” to connect. • When the music is streamed, the track, title and artist of the song will scroll on the display panel. CONNECTED HK ENCHANT 1300 HK ENCHANT 800 NOTES: • • • • • • • If you have already connected the soundbar to Wi-Fi and changed the device name, then select the new device name. If asked for a PIN code when connecting a Bluetooth device, enter “0000”. To exit Bluetooth mode, choose other sources.
/ USING YOUR SOUNDBAR 2) Press the button on the top panel of the soundbar or the SOURCE button on the remote control to select the USB mode. • If USB is detected, “LOADING” will be displayed and music will be played automatically. File names will appear on the display panel. If no USB detected, “PLUG IN USB” is displayed. USB playback controls • : Start, pause or resume play. • / : Skip to the previous or next track. • SHUFFLE: • Off (default): play songs in order. • Shuffle: play songs randomly.
Codec Sample rate Bitrate MP3 MPEG1 layer1/2/3 32Khz ~48Khz 32kbps~320kbps MPEG2 layer1/2/3 16Khz ~24Khz 8kbps~160kbps MPEG2.
/ Settings Calibrate the Soundbar with Automatic MultiBeam™ Calibration (AMC) Automatic MultiBeam Calibration (AMC) will optimize the soundbar sound settings for a better surround sound experience. 1) Press and hold the CALIBRATION button for 3 seconds. • The calibration sequence will begin with a countdown. >3 s 2) The total calibration will last less than 60 seconds. • “DONE” will be displayed once successfully calibrated, while “FAIL” will be displayed if the calibration fails.
/ S ettings Respond to TV Remote Control HDMI CEC If you are using an HDMI ARC connection to your television, then your TV remote control will automatically operate the soundbar for standard commands such as power on/off and volume control. The soundbar supports HDMI CEC and will interoperate with compatible TV’s (check your TV owner’s manual for HDMI CEC compatibility) Automatic TV Remote Control For most Samsung, LG, Sony and Vizio TVs, the soundbar responds to your TV remote control automatically.
/ S ettings 4) Press and hold + and on the soundbar again, now the soundbar responds to your TV remote control. DONE Auto Standby / Auto Wakeup This soundbar automatically switches to standby after 10 minutes of button inactivity, and no audio/video playback is detected from a connected device. This soundbar will automatically power on again if it receives an audio signal from the last detected connection. Apply Factory Settings Reset the soundbar to the default settings programmed at the factory.
/ UPDATE SOFTWARE To get the best features and support, update the soundbar with the latest software. You need: • Wi-Fi network. • A computer with Internet access. • A USB flash drive that is FAT-formatted. Check the Current Version To check the current version, press and hold DIM LEVEL for 3 seconds, then press SOUND MODE and NIGHT MODE in sequence within 10 seconds. Update the Software 1) The latest version of the software can be found when connected to a network.
/ SPECIFICATIONS Audio/Video Audio Channels Maximum Power RMS Power Total Harmonic Distortion (THD) Woofer Size Tweeter Size Max SPL Frequency Response Audio inputs HDMI Video Inputs HDMI Video Output (with Audio Return Channel) HDMI HDCP Version HDR Bluetooth Bluetooth version Bluetooth Profile Bluetooth Frequency Range Bluetooth Max Transmitting power Bluetooth Transmitter modulation Enchant 800 Enchant 1300 8 180W 90W 1% 13 240W 120W 1% 6 x 2” (50mm) 2 x 1” (25mm) 91db SPL 76Hz-20kHz 1 Analog, 1 Opt
/ S P E C I F I C AT I O N S Wi-Fi Wi-Fi network compatibility 2.4G Wi-Fi Frequency Range 2.4G Max Transmitting power 2.4G Wi-Fi modulation 5G Wi-Fi maximum transmitter power 5G Wi-Fi modulation 5G Wi-Fi transmitter frequency range 2.4G short-range wireless frequency range 2.4G short-range wireless maximum transmitter power 2.4G short-range wireless modulation USB USB Compatibility USB Class support USB File Formats Enchant 800 Enchant 1300 IEEE 802.11b/g/n/ac (2.4G/5G) 2412 – 2472MHz (2.
/ S P E C I F I C AT I O N S USB File system USB File Formats USB port General Power Supply Power Consumption Standby Power Consumption Operating temperature Dimensions(W x H x D) Accessory Cable Length Weight Packaging Dimensions (W x H x D) Packaging Weight (Gross) Enchant 800 FAT16, FAT32 .mp3, .wav, .aac, .flac, .ogg 5V 1A Enchant 1300 FAT16, FAT32 .mp3, .wav, .aac, .flac, .ogg 5V 1A 100-240V~50/60Hz 33 W <2W 100-240V~50/60Hz 48 W <2W 0°C - 45°C 33.8” x 2.6” x 4.
/ S P E C I F I C AT I O N S Enchant Subwoofer Audio/Video Maximum Power RMS Power Total Harmonic Distortion (THD) Woofer Size Max SPL Frequency Response Wireless 2.4G short-range wireless frequency range 2.4G short-range wireless maximum transmitter power 2.
/ TROUBLESHOOTING Never try to repair the product yourself. If you have any problems using this product, check the following points before you request service. Sound No sound from the soundbar. • Make sure that the soundbar is not muted. • Make sure to select the correct audio input source. Strange sound. • Press and hold SOUND MODE for 5 seconds to reset the default audio setting. No sound from the wireless subwoofer. • Check if the subwoofer LED is in solid white color.
/ TROUBLESHOOTING Bluetooth A device cannot connect with the soundbar. • Check if you enable the Bluetooth function of the device. • The soundbar is already connected to another Bluetooth device. Press and hold BT on remote control to disconnect and pair with a new device. Poor audio quality from a connected Bluetooth device. • The Bluetooth reception is poor. Move the device closer to the soundbar, or remove any obstacle between the device and the soundbar.
/ OPEN SOURCE LICENSE NOTICE This product contains open source software. For your convenience, the source code and relevant build instruction for software licensed under the GPL is available at http://www.harmankardon.com/ opensource. You may also obtain this information by contacting us at OpenSourceSupport@Harman.
/ LICENSE The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners. Manufactured under license from Dolby Laboratories. Dolby,Dolby Audio,Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.