HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 1 HKTS 15 HOME THEATER SPEAKER SYSTEM OWNER’S MANUAL
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 2 HKTS 15 HOME THEATER SPEAKER SYSTEM 3 4 4 5 7 7 8 9 9 10 11 12 13 13 13 14 15 Safety Information Introduction Included SUB-TS15 Subwoofer Amplifier Panel Controls and Connections Speaker Placement Color-Coding System Mounting Options Speaker Connections Speaker-Level Connection Guide Dolby Digital or DTS (or Other Digital Surround Mode) Connection Dolby Pro Logic (Non-Digital) – Line Level Dolby Pro Logic (Non-Digital) – Speaker Level Operation Volume Ad
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 3 SAFETY INFORMATION Read First! Important Safety Precautions! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 4 INTRODUCTION Introduction Thank you for purchasing the Harman Kardon® HKTS 15, with which you’re about to begin many years of listening enjoyment. The HKTS 15 has been custom-designed to provide all the excitement and power of the cinema experience in your own living room. To obtain maximum enjoyment from your new home theater speaker system, we urge you to take a few minutes to read through this manual.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 5 SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS ¡ Subwoofer-Level Control ™ High-Cut (Low-Pass) Filter Switch £ External Trigger Input ¢ Audio-Sense On/Off Switch ∞ Phase Switch § Line-Level Subwoofer (SUB) Input ¶ Line-Level Full-Range Inputs • Speaker-Level Outputs ª Speaker-Level Inputs ‚ Master Power Switch ⁄ AC Power Cord ¡ Subwoofer-Level Control: Volume may be adjusted using the SubwooferLevel Control.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 6 SUB-TS15 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS place itself in the Standby mode, depending on whether it is receiving an audio signal. When this switch is placed in the ON position, the SUB-TS15 will remain on, whether or not it is receiving an audio signal. An LED located on top of the SUB-TS15 indicates whether the SUB-TS15 is in the ON or STANDBY state when used with the Audio-Sense On/Off Switch ¢ in the AUTO position.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 7 SPEAKER PLACEMENT Color-Coding System The HKTS 15 uses the channel color-coding system established by the Consumer Electronics Association to make setting up your home theater speaker system as easy as possible. Your system includes a set of colored stickers that may be placed near the speaker terminals of each of the four satellite speakers according to the key below.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 8 MOUNTING OPTIONS Satellites and Surrounds The satellite speakers may be placed on a shelf. Place each satellite speaker on one of the supplied coasters for added stability and to protect your furniture. They may be wallmounted using the supplied brackets. Wall-Mounting Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker. Store the stand and bolt in a safe place in case they are needed for a future installation.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 9 SPEAKER CONNECTIONS Speaker-Level Connection Guide IMPORTANT NOTE: Before making speaker connections, be certain that your receiver or audio power amplifier is turned off and preferably unplugged from its AC power source. The SUB-TS15 subwoofer should not be connected to an AC power source until all speaker wire connections have been made. Speakers and electronics terminals have corresponding (+) and (–) terminals.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 10 SPEAKER CONNECTIONS Dolby ® Digital or DTS® (or Other Digital Surround Mode) Connection USE THIS INSTALLATION METHOD FOR DOLBY DIGITAL, DTS OR OTHER DIGITAL SURROUND PROCESSORS: Center – + Front Left – + SUB-TS15 Subwoofer Use the line-level input jack marked SUB § for the Low-Frequency Effects channel. Connect this jack to the subwoofer output or LFE output on your receiver or amplifier.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 11 SPEAKER CONNECTIONS Dolby Pro Logic® (Non-Digital) – Line Level USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR IS EQUIPPED WITH A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Use the supplied RCA-type interconnect cable to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Ful
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 12 SPEAKER CONNECTIONS Dolby Pro Logic (Non-Digital) – Speaker Level USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR DOES NOT HAVE A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Center Front Left – – + – H I G H L E V E L Connect your receiver or amplifier’s center and surround left and right speaker terminals to the corresponding
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 13 OPERATION Move the Master Power Switch ‚ (marked Power) to the “•” (On) position. The SUB-TS15 subwoofer will automatically turn itself on or go into Standby mode, depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the AudioSense On/Off Switch ¢ is moved down so that it is in the AUTO position.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 14 TROUBLESHOOTING SYMPTOM SOLUTION If there is no sound from any of the speakers: • Check that receiver/amplifier is on and a source is playing. • Check that the powered subwoofer is plugged in and its Master Power Switch ‚ is switched on to the “•” position. • Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching other wires.
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 15 HKTS 15 SPECIFICATIONS HKTS 15 System Frequency Response: 35Hz – 20kHz (–6dB) SAT-TS15 Satellites Recommended Power: 10 – 80 Watts Impedance: 8 Ohms nominal Sensitivity: 86dB @ 1 Watt/1 meter Tweeter: One 1/2" dome, video-shielded Midrange: One 3" driver, video-shielded CEN-TS15 Center SUB-TS15 Subwoofer Recommended Power: 10 – 80 Watts Amplifier: 100 Watts RMS Impedance: 8 Ohms nominal Bass: 10" Woofer, bass-reflex enclosure Sensitivity: 86dB @
HKTS15-120V-omHKTS 15 OM 9/12/06 11:52 AM Page 16 250 Crossways Park Drive, Woodbury, New York 11797 516.255.4545 (USA only) Fax: 516.682.3523 © 2006 Harman International Industries, Incorporated. All rights reserved. Part No.
