Onyx Wireless Speaker System with Rechargeable Battery Owner’s Manual
Onyx Table of Contents INTRODUCTION 3 DESCRIPTION AND FEATURES 3 DESIGN AND PERFORMANCE 3 WIRELESS CONNECTION 3 INCLUDED ITEMS 3 CONTROLS AND CONNECTIONS 3 ONYX TOP PANEL CONTROLS 3 ONYX REAR PANEL CONNE CTIONS AND CONTROLS 4 SPEAKER PLACEMENT 4 CONNECTIONS 4 POWER CONNECTIONS 4 SOURCE OPTIONS 4 WI-FI CONNECTION 4 BLUETOOTH CONNECTION 4 WPS CONNECTION 5 IOS WIRELESS WI-FI SHARING 5 IOS WI-FI SHARING WITH CABLE 5 AD-HOC MODE 6 OPERATION 6 SWITCHING ON AND OFF
Onyx Introduction Thank you for purchasing the Harman Kardon Onyx. HK Onyx is a premium wireless speaker with an iconic design and comes with a rechargeable inbuilt battery that allows you to stream music from any smart phone, tablet or other wireless devices through Bluetooth®, AUX, Wi-Fi, AirPlay® and DLNA®. HK Onyx is a 4-speaker, advanced acoustic platform and its dual passive radiators deliver a truly fantastic sound experience with a balanced soundstage and powerful bass response.
Onyx Speaker Placement NOTE: When the system gets into Operational mode either from the Sleep/ Standby mode or OFF mode, the last used settings will be restored – volume, source, Wi-Fi settings.volume, source, Wi-Fi settings. Volume Controls These touch-sensitive buttons control the volume of the unit. These buttons are touchsensitive. A gentle finger touch can increase or decrease the volume.
Onyx Speaker Placement The iPhone, iPad or iPod Touch will then share Wi-Fi settings with the Harman Kardon Onyx and Onyx will be connected to your Wi-Fi network. This takes at least 40 seconds. Once the Harman Kardon Onyx is connected to the network, the Wi-Fi LED will light constant white and a sound prompt will be heard. iOS Wi-Fi Sharing with Cable WPS Connection Wi-Fi Protected Setup (WPS) is a simple way of getting your speaker to connect to the desired network. Your router may support WPS.
Onyx Operation NOTE: To restore the factory default settings, long press Bluetooth and Power button in Operational mode.
Onyx Operation Playing Music through Wi-Fi H/K Remote To play music in your Onyx through Wi-Fi: 1. Press the Power button. The LED will illuminate white. 2. Connect to your Wi-Fi network by following the above procedures. 3. If Harman Kardon Onyx is on Wi-Fi network, the Wi-Fi LED becomes constant white. 4. Control playback from your Wi-Fi enabled device. HK Onyx can be operated through the H/K Remote app available in the App Store for Apple products or Google Play for Android products.
Onyx Troubleshooting Troubleshooting If your Harman Kardon Onyx is not performing the way you think it should, check if the problem is covered in this section before calling your dealer or contacting a Harman Kardon representative. Problems There is no sound coming from the HK Onyx Distortion (static, crackling or hissing sounds) HK onyx emits a loud hum or buzzing noise HK Onyx unit is not charging Solutions • No power to unit. Make sure that the wall outlet or power strip has power.
Onyx Specifications Specifications Frequency Range 2402MHz – 2480MHz Frequency Response 60Hz – 20kHz No of channels 4 Transducers 2 X 3 woofers, 2 X ¾ tweeters, 2 passive radiators Bi-amplification 4 X 15W Maximum SPL 95dB @ 1m Power Requirement 100 – 240 V AC, 50/60 Hz Power adaptor 19V, 3.4 A Built-in Battery 11.1V, 2500mAh Lithium Power consumption 54M Maximum, <1W stand by Speaker impedance 4 ohm per speaker Transmitter power <4dBm Modulation GFSK/ .
© 2013 HARMAN International Industries, Incorporated. All rights reserved. Harman Kardon is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. The “beautiful/sound” logo is a trademark of HARMAN International Industries, Incorporated. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license.
