RCP7 OM.
RCP7 OM.
RCP7 OM.qxd 3/23/07 4:15 PM Page 3 INTRODUCTION AND FEATURES Please register your product on our Web site at www.harmankardon.com. Note: You’ll need the product’s serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW.HARMANKARDON.
RCP7 OM.qxd 3/23/07 4:15 PM Page 4 REMOTE CONTROL FUNCTIONS The RCP 7 remote is capable of controlling 11 devices, including the AVR 347 and the DVD 48 included in the CP 65 system. During the installation process, you may program the codes for each of your source components into the remote. Each time you wish to use the codes for any component, first press that component’s selector. This changes the button functions to the appropriate codes for that product.
RCP7 OM.
RCP7 OM.qxd 3/23/07 4:15 PM Page 6 REMOTE CONTROL FUNCTIONS XM Radio Button: Press this button to select XM Satellite Radio as the source. You will need to have purchased and activated an XM® antenna module, and you will also need to subscribe to the XM Radio service. Visit www.xmradio.com for more information. Learn Button: The RCP 7 remote is capable of “learning” individual IR codes from the original remote that came with your TV or a device that is connected to any of the source inputs.
RCP7 OM.qxd 3/23/07 4:15 PM Page 7 REMOTE CONTROL FUNCTIONS Tuning Mode/Zoom: When listening to AM or FM radio, this button toggles between Manual (one frequency step at a time) and Automatic (seeks frequencies with acceptable signal strength) tuning modes. It also toggles between Stereo and Mono modes when an FM station is tuned. When listening to XM Radio, press the Tuning Mode Button once to view the category name of the current channel.
RCP7 OM.qxd 3/23/07 4:15 PM Page 8 REMOTE CONTROL FUNCTIONS Logic 7® Surround Mode Selector/Random: The first press of this button will select the last-used Logic 7 Surround mode if it is available, and each additional press will cycle through the Cinema, Music and Enhance modes. See the AVR 347 manual for more information. When the DVD player has been selected, this button serves the Random function.
RCP7 OM.qxd 3/23/07 4:15 PM Page 9 BATTERIES The RCP 7 remote control uses three AAA batteries, which are included. To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover toward the top of the remote. Insert the batteries as shown in Figure 1, making sure to observe the correct polarity. Figure 1 – Remote Battery Compartment When using the remote, remember to point the lens toward the front panel of the AVR 347 or DVD 48.
RCP7 OM.qxd 3/23/07 4:15 PM Page 10 PROGRAMMING SOURCES Programming Sources The RCP 7 remote is capable of controlling not only the receiver and DVD player included in your CP system, but it may also be programmed to control many brands and models of VCRs, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod device (not included) docked in Harman Kardon’s optional The Bridge. It may help to think of the remote as a book with pages.
RCP7 OM.qxd 3/23/07 4:15 PM Page 11 PROGRAMMING SOURCES Table 1 – Remote Control Codes Source Input Video 1 Video 2 Video 3 Video 4 HDMI 1 HDMI 2 DVD * CD Tape Product Type (circle one) VCR, PVR Cable, Satellite TV TV DVD, VCR, Cable, Satellite DVD, VCR, Cable, Satellite DVD CD, CD-R Cassette Remote Control Code * Do not reprogram the DVD Source selector unless you are replacing the DVD player included in the CP 65 system with another product. 7.
RCP7 OM.qxd 3/23/07 4:15 PM Page 12 LEARNING INDIVIDUAL KEY CODES The following keys on the RCP 7 remote may be programmed with individual IR codes that are “learned” from another remote control: Power On/Off, Mute, Sleep/Audio and DSP Surround/Title (Channel Up/Down), Volume Controls, Channel Level/Disc Menu, Speaker/DVD Setup, Digital Input/Drawer Open/Close, Delay/DVD Status, ‹ › ⁄¤ Navigation, Set/Enter, Numeric Keys, Track Skip Up/Down and Transport Controls – a total of 34 buttons.
RCP7 OM.qxd 3/23/07 4:15 PM Page 13 ADVANCED FUNCTIONS The RCP 7 remote control not only operates the AVR 347 and DVD 48, but it also serves as a universal remote that may be programmed to operate many of your other home theater components. The punchthrough and macro features add even more flexibility and versatility.
RCP7 OM.qxd 3/23/07 4:15 PM Page 14 ADVANCED FUNCTIONS It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows: 1. Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the Program LED flashes. 2. Press the Surround Button to erase the macro. Resetting the Remote To reset the remote to its factory defaults, simultaneously press and hold any Input Selector and the “0” Numeric Key.
RCP7 OM.qxd 3/23/07 4:15 PM Page 15 APPENDIX 2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 27 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 71 70 72 Refer to the numbered buttons in this drawing when using the Function List.
RCP7 OM.qxd 3/23/07 4:15 PM Page 16 APPENDIX Table A1 – Remote Control Function List No.
RCP7 OM.qxd 3/23/07 4:15 PM Page 17 APPENDIX Table A1 (continued) No.
RCP7 OM.qxd 3/23/07 4:15 PM Page 18 APPENDIX Refer to Tables A2 through A9 when programming the codes for your components into the remote.
RCP7 OM.
RCP7 OM.
RCP7 OM.
RCP7 OM.
RCP7 OM.
RCP7 OM.qxd 3/23/07 4:15 PM Page 24 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com © 2007 Harman International Industries, Incorporated. All rights reserved. Part No.
