User Manual

14221-1200-2000, Rev. A
17
MESSAGE NAME DESCRIPTION
GRP=1-1250
Group = 1 - 1250
The group number of the group displayed in line 2 of display. It is displayed in line 1 of
the display. Press the group key to obtain this display. The maximum number of
groups programmed in a radio is determined by the personality.
INDV=1-255
Individual = 1 - 255
Indicates which item in the individual call list is being displayed. It is displayed in line 2
of the display. The name or ID of the item in the list is displayed in line 1 of the
display.
SEL INDV
Select Individual ID
Displayed on line 1 when an entry from the individual ID list is selected after pressing
the INDV key. The entry is a number between 1 and 32 inclusive.
SYS ALL
System All Call Displayed on line 1 to indicate a system all-call has been received.
Ggg-v.vv
Code Group and
Revision Number
This is code group and revision number that is displayed in line 2 when the menu item
“REVISION” is selected. The ‘gg’ is the group number of the software. The first ‘v’ is
the hardware version and ‘vv’ is the revision of the software.
NO ENTRY
Indicates that there is no data stored in one of the programmable items. The user
programmable items are items 1 through 10 in each list.
INV SYS
Invalid System Displayed when the current system is an invalid type.
INV CHAN
Invalid Channel
Displayed when the current system is valid, but the channel is invalid (the feature bit
for one frequency band is turned off).
CHN=1-1000
Channel = 1 - 1000
Displayed on line 1 of the display. This is a conventional channel index displayed
when the group key is pressed.
FIX LIST
Fixed List The Priority scan list is fixed and cannot be changed using add or delete keys.
FIXED P1
Fixed Priority 1 The Priority 1 scan channel is fixed and cannot be changed using add or delete keys.
EM
Emergency
Indicates an emergency has been declared by the LID that follows the display, “EM.”
An example of this is “EM 01201.”
*INDV*
Individual Call Displayed in line 2 of the display when an individual call is in progress.
SPKR ON
External Speaker ON Displayed when the external speaker is enabled.
SPKR OFF
External Speaker
OFF
Displayed when the external speaker is disabled.
BANK=1-8
The bank of keys that are going to be loaded when the keyloader loads encryption
keys. This is only valid for radios that support VGS, VGE, or DES encryption. It is
displayed on line 2 of the display when the encryption keyloader is connected.
REGR_0x
Dynamic Regroup
Indicates which group in the dynamic regroup operation has been enabled, where “x”
is a digit of 1 to 8.
KEY LOAD
Displayed on line 1 of the display when the encryption keyloader is connected.
KEY ZERO
Displayed on line 2 of the display when the reset and option buttons are pressed
simultaneously for approximately two seconds. The encryption keys are zeroed.
SYS KEY
System Key
Displayed on line 1 of the display in the display key mode of the menu. It is followed in
the second line with a key number “KEY = <1..7>.”
GRP KEY
Group Key
Displayed on line 1 of the display in the display key mode of the menu for trunked
systems only. It is followed in the second line with a key number “KEY = <1..7>.”
KEY=1-7
Displayed on line 2 of the display in the display key mode of the menu for
conventional systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and
for trunked systems when the “SYS KEY” or “GRP KEY” is displayed in line 1.
PRIMARY
Displayed on line 1 of the display when the primary keys are enabled.
PRS NAME
Personality Name
Displayed on line 1 of the display
under the revision selection of the menu. The
personality name is displayed on line 2 at the same time.
BND SCAN
Band Scan
Only displayed if the P25T system is configured for "EnhancedCC" mode of
operation. When the radio cannot find a Control Channel in
either the trunked
frequency set or the list of discovered adjacencies, the radio is able to perform a full
spectrum frequency scan to find a new Control Channel.
REGISTER
Displayed when the radio is performing a registration/affiliation on a P25 trunking site.