User's Manual

ManualsBrandsHARRIS ManualsElectronicsXG-75M/M7300 Series Mobile Radio

Rhein Tech Laboratories, Inc. Client: Harris Corporation

360 Herndon Parkway Model #: XG-75M/M7300/M5300,35W

Suite 1400 ID’s: OWDTR-0132-E/3636B-0132

Herndon, VA20170 Standards: FCC Part 90

http://www.rheintech.com Report #: 2014021

166 of 199

Appendix O: Manual

Please refer to the Operators Manuals and Safety Manuals.

Summary of content (266 pages)

PAGE 1
Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA20170 http://www.rheintech.com Appendix O: Client: Harris Corporation Model #: XG-75M/M7300/M5300,35W ID’s: OWDTR-0132-E/3636B-0132 Standards: FCC Part 90 Report #: 2014021 Manual Please refer to the Operators Manuals and Safety Manuals.
PAGE 2
Operator’s Manual MM-014716-001 Rev.
PAGE 3
MM-014716-001, Rev. P MANUAL REVISION HISTORY REV DATE REASON FOR CHANGE C Sep/09 Added VHF antennas, added “Enable/Disable Volume Side Tone,” and updated to Harris format. D Apr/10 Added keypad lock/unlock instructions for ECP, added REGISTER and BND SCAN to P25T status messages. E Jan/11 Updated antenna information; other minor updates. F Apr/11 Updated for OTP R17, consolidated EDACS, Conventional, P25 operation into one section.
PAGE 4
MM-014716-001, Rev. P TABLE OF CONTENTS Page 1. REGULATORY AND SAFETY INFORMATION............................................................................. 9 1.1 SAFETY SYMBOL CONVENTIONS ......................................................................................... 9 1.2 REGULATORY APPROVALS ................................................................................................. 10 1.2.1 Applicable Type Acceptance/Certification Numbers ..............................................
PAGE 5
MM-014716-001, Rev. P TABLE OF CONTENTS Page 6. 4 OPENSKY OPERATION (700/800 MHZ RADIOS ONLY)............................................................ 44 6.1 CH-721 FRONT PANEL COMPONENTS ................................................................................ 44 6.2 POWER UP AND VOLUME CONTROL ................................................................................. 46 6.2.1 Power Up ......................................................................................................
PAGE 6
MM-014716-001, Rev. P TABLE OF CONTENTS Page 6.28 6.29 6.30 6.31 6.32 6.33 6.34 6.35 6.36 6.37 7. MAKE SELECTIVE CALLS ..................................................................................................... 65 6.28.1 Manually Dial a Selective Call (System Model Control Head)..................................... 65 6.28.2 Speed Dial a Selective Call............................................................................................ 66 6.28.3 Receive a Selective Call ...........
PAGE 7
MM-014716-001, Rev. P TABLE OF CONTENTS Page 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 6 7.11.1 System Selection............................................................................................................ 88 7.11.2 Group and Channel Selection ........................................................................................ 88 LAST SYSTEM/GROUP/CHANNEL RECALL .......................................................................
PAGE 8
MM-014716-001, Rev. P TABLE OF CONTENTS Page 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 7.36 7.37 7.38 7.27.3 Data On Operation ....................................................................................................... 102 7.27.4 Exiting Data Calls ........................................................................................................ 103 7.27.5 Scan Lockout Mode ..................................................................................................... 103 7.27.
PAGE 9
MM-014716-001, Rev. P TABLE OF CONTENTS Page TABLES Table 1-1: FCC Type Acceptance .......................................................................................................... 10 Table 1-2: Industry Canada Type Acceptance........................................................................................ 10 Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) ...........................................................................................
PAGE 10
MM-014716-001, Rev. P 1. REGULATORY AND SAFETY INFORMATION 1.1 SAFETY SYMBOL CONVENTIONS The following conventions are used in this manual to alert the user to general safety precautions that must be observed during all phases of operation, installation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere violates safety standards of design, manufacture, and intended use of the product.
PAGE 11
MM-014716-001, Rev. P 1.2 REGULATORY APPROVALS 1.2.1 Applicable Type Acceptance/Certification Numbers Table 1-1: FCC Type Acceptance RADIO PART NUMBER FCC TYPE ACCEPTANCE NUMBER FREQUENCY RANGE/WATTAGE RU-144750-041 136-174 MHz, 50 Watt OWDTR-055-E RU-144750-051 136-174 MHz, 110 Watt OWDTR-056-E RU-144750-021 378-430 MHz, 50 Watt OWDTR-061-E RU-144750-031 440-512 MHz, 50 Watt OWDTR-062-E 14018-0010-01 330-380 MHz, 40 Watt N/A RU-144750-061 Rev.
PAGE 12
MM-014716-001, Rev. P 1.3 RADIO FREQUENCY INTERFERENCE 1.3.1 FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and, 2. This device must accept any interference received, including interference that may cause undesired operation. 1.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s).
PAGE 13
MM-014716-001, Rev. P of protection. All two-way radios marketed in North America are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it.
PAGE 14
MM-014716-001, Rev. P Based on the highest radiated RF power and the highest antenna gain in antennas used with XG75M/M7300 series radios, the distances listed in Table 1-3 and Table 1-4 are considered as safe distances for controlled and uncontrolled environments with the XG-75M/M7300 series mobile radios transmitting at a maximum 50% duty cycle: 1.5.
PAGE 15
MM-014716-001, Rev. P 1.5.3 Mobile Antennas (Vehicle Installations) Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER VHF (50 W) AN-225002-001 136 to 174 MHz, 0 dBd Gain VHF (50 W) AN-225006-001 132 to 960 MHz, 0 dBd Gain* VHF (50 W) AN-225002-003 ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 24.
PAGE 16
MM-014716-001, Rev. P Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 20 Inches (51 Centimeters) 45 Inches (114 Centimeters) 9.8 Inches (25 Centimeters) 21.
PAGE 17
MM-014716-001, Rev.
PAGE 18
MM-014716-001, Rev. P Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER 700/800 MHz * ANTENNA DESCRIPTION STI-Co CCAS-SB-700 760 - 820 MHz Concealed Peal-and-Stick InternalMount; dBi Gain RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 7.9 Inches (20 Centimeters) 19.
PAGE 19
MM-014716-001, Rev. P A radio used in a motorcycle installation must be configured with a transmit output power level less than or equal to the MAX. TX POWER (WATTS) specification listed in Table 1-4 for the respective frequency band and antenna/antenna element. Refer to the radio’s Installation Manual for additional information.
PAGE 20
MM-014716-001, Rev. P x Interference To Vehicular Electronic Systems — Electronic fuel injection systems, electronic antiskid braking systems, electronic cruise control systems, etc., are typical of the types of electronic devices that can malfunction due to the lack of protection from radio frequency (RF) energy present when transmitting.
PAGE 21
MM-014716-001, Rev. P 1.9 OPERATING RULES AND REGULATIONS Two-way radio systems must be operated in accordance with the rules and regulations of the local, regional, or national government. In the United States, the XG-75M/M7300 mobile radio must be operated in accordance with the rules and regulations of the Federal Communications Commission (FCC). Operators of two-way radio equipment must be thoroughly familiar with the rules that apply to the particular type of radio operation.
PAGE 22
MM-014716-001, Rev. P NOTE In areas where transmission or reception is poor, communication improvement may sometimes be obtained by moving a few yards in another direction, or moving to a higher elevation.
PAGE 23
MM-014716-001, Rev. P 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit.
PAGE 24
MM-014716-001, Rev. P 2.2 CONFORMITÉ À LA RÉGLEMENTATION 2.2.
PAGE 25
MM-014716-001, Rev. P appareil doit accepter toute interférence, y compris une interférence qui peut causer un fonctionnement non souhaité de l’appareil. 2.4 RENSEIGNEMENTS SUR UNE EXPOSITION À L’ÉNERGIE DES RF 2.4.
PAGE 26
MM-014716-001, Rev. P 2.4.1.1 Règlements de la Federal Communications Commission (« Commission fédérale des communications » aux États-Unis) Avant d’être mise sur le marché aux États-Unis, la radio mobile bidirectionnelle XG-75M/M7300 a été testée pour s’assurer de sa conformité aux limites d’exposition à l’énergie des RF de la FCC pour les radios mobiles bidirectionnelles.
PAGE 27
MM-014716-001, Rev. P contrôlés et non contrôlés avec la radio mobile XG-75M/M7300 qui transmet à un cycle de service maximal de 50 %. 2.5.1 Antennes mobiles Les antennes pour la radio doivent être installées conformément aux procédures présentées dans le Manuel sur la sécurité du produit et dans le Manuel d’installation. L’installation est limitée à un ou des véhicules motorisés en métal avec des plans au sol appropriés.
PAGE 28
MM-014716-001, Rev. P 2.5.
PAGE 29
MM-014716-001, Rev.
PAGE 30
MM-014716-001, Rev.
PAGE 31
MM-014716-001, Rev.
PAGE 32
MM-014716-001, Rev.
PAGE 33
MM-014716-001, Rev. P 2.5.4 Monté Antennes (Motocyclette) Tableau 2-4: Distance latérale sécuritaire minimale recommandée d’une antenne de transmission branchée sur une radio Motocyclette RF BAND VHF VHF UHF- L UHF - H 800 MHz 700 or 800 MHz NUMÉRO DE PIÈCE DE L’ÉLÉMENT DE L’ANTENNE DESCRIPTION DE L’ANTENNE LE-OM150K.125/TNC 136 to 174 MHz motocyclettemonture; gain de 2.
PAGE 34
MM-014716-001, Rev. P 2.6 RENSEIGNEMENTS SUR LA FORMATION SUR LA SANTÉ ET LA SÉCURITÉ AU TRAVAIL S’assurer que l’exposition physique à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle. Toujours se conformer aux directives de base suivantes: x Le bouton de microphone doit être abaissé seulement lorsque l’on souhaite envoyer un message vocal. x La radio doit être utilisée seulement pour les communications nécessaires liées au travail.
PAGE 35
MM-014716-001, Rev. P x Énergie des fréquences radio – Pour prévenir toute brûlure ou toute blessure physique connexe causée par l'énergie des fréquences radio, ne pas faire fonctionner l'émetteur lorsqu'une personne à l'extérieur du véhicule est située en deçà de la distance minimale sécuritaire de l'antenne, comme stipulé à la Section 2.5.
PAGE 36
MM-014716-001, Rev. P 2.9 RÈGLES ET RÉGLEMENTATIONS D'UTILISATION Les systèmes de radio émetteur-récepteur doivent être utilisés conformément aux règles et réglementations du gouvernement local, régional ou national. Aux États-Unis, la radio mobile XG-75M/M7300 doit être utilisée conformément aux règles et réglementations de la Commission fédérale des communications (FCC).
PAGE 37
MM-014716-001, Rev. P 3. MARINE FREQUENCIES Refer to Table 3-1: Marine Frequencies for a list of maritime frequencies per United States Coast Guard (USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department Fisheries and Oceans, August 2009: x United States (US) x International (Intl) x Canada (CA) Table 3-1: Marine Frequencies CHANNEL US INTL 1 CA 1 1a CHANNEL USAGE T: 156.05 R: 160.65 T: 160.65 R: 156.
PAGE 38
MM-014716-001, Rev. P Table 3-1: Marine Frequencies CHANNEL US INTL CA FREQUENCY SHIP SHORE (MHZ) (MHZ) CHANNEL USAGE 10 10 10 T/R: 156.50 T/R: 156.50 US: Commercial International: Intership, Port Operations Canada: Commercial - British Columbia coast area. May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. 11 11 11 T/R: 156.55 T/R: 156.55 US: Commercial. VTS in selected areas.
PAGE 39
MM-014716-001, Rev. P Table 3-1: Marine Frequencies CHANNEL US 20 INTL 20 CA 20 T: 161.60 R: 157.00 US: Port Operations (Duplex) International: Public Correspondence, Port Operations Canada: Port operations only with 1 watt maximum power. T/R: 157.00 T/R: 157.00 US: Port Operations T: 157.05 R: 161.65* T: 161.65* R: 157.05 International: Public Correspondence, Port Operations 21a T/R: 157.05 T/R: 157.05 US: US Coast Guard only Canada: DFO/Canadian Coast Guard only. 21b -- T/R: 161.
PAGE 40
MM-014716-001, Rev. P Table 3-1: Marine Frequencies CHANNEL US INTL CA 62 T: 160.725 R: 156.125 International: Public Correspondence, Port Operations T/R: 156.125 T/R: 156.125 Canada: DFO/Canadian Coast Guard only in British Columbia coast area. T: 156.175 R: 160.775 T: 160.775 R: 156.175 International: Public Correspondence, Port Operations 63a T/R: 156.175 T/R: 156.175 US: Port Operations and Commercial, VTS. New Orleans/Lower Mississippi area.
PAGE 41
MM-014716-001, Rev. P Table 3-1: Marine Frequencies CHANNEL US INTL CA FREQUENCY SHIP SHORE (MHZ) (MHZ) CHANNEL USAGE 72 72 72 T/R: 156.625 T/R: 156.625 US: Non-Commercial (Intership only) International: Intership Canada: May be used to communicate with aircraft and helicopters in predominantly maritime support operations. Pleasure craft - British Columbia coast area 73 73 73 T/R: 156.675 T/R: 156.
PAGE 42
MM-014716-001, Rev. P Table 3-1: Marine Frequencies CHANNEL US INTL CA 83 83a FREQUENCY SHIP SHORE (MHZ) (MHZ) CHANNEL USAGE T: 157.175 R: 161.775 T: 161.775 R: 157.175 International: Public Correspondence, Port Operations 83a T/R: 157.175 T/R: 157.175 US: US Coast Guard only Canada: DFO/Canadian Coast Guard and other Government agencies. 83b -- T/R: 161.775 84 84 84 T: 157.225 R: 161.825 T: 161.825 R: 157.
PAGE 43
MM-014716-001, Rev. P 4. PRODUCT DESCRIPTION The XG-75M/M7300 mobile is a state-of-the-art radio designed to meet the critical demands of its users. The XG-75M/M7300 mobile supports multiple operating modes, including OpenSky® digital trunked operation (700/800 MHz radios only), Enhanced Digital Access Communications System (EDACS®) or ProVoiceTM trunked modes, P25 digital trunked mode, P25 digital conventional mode, and analog conventional mode.
PAGE 44
MM-014716-001, Rev. P 5. CHANGE OPERATING MODE (700/800 MHZ RADIOS ONLY) 5.1 CHANGE FROM OTP MODE To change from OTP operating mode to EDACS, Conventional, and P25 (ECP/XGP) Modes: 1. Use , CLEAR/CLR, or OPTION/OPT to cycle through the menu until the “App Mode” appears in the bottom line of the display. 2. Use to choose an available mode. Press MENU and confirm (Y/N) with MENU again. and press 3. Press the MENU button to confirm.
PAGE 45
MM-014716-001, Rev. P 6. OPENSKY OPERATION (700/800 MHZ RADIOS ONLY) 6.1 CH-721 FRONT PANEL COMPONENTS The front panel of the control head includes a dot matrix display, controls for menu navigation, an emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone connector. In addition, the system model control head features a DTMF keypad (Figure 6-1).
PAGE 46
MM-014716-001, Rev. P Table 6-1: Front Panel Default Controls and Functions PART FUNCTION Power OnOff/Volume Control Knob Turn knob clockwise to power on the radio and increase volume. Turn counter-clockwise to decrease volume and power off the radio. Mic Connection Connection for hand-held, hands-free, speaker-mic, headset, or programming cable.
PAGE 47
MM-014716-001, Rev. P 6.2 POWER UP AND VOLUME CONTROL 6.2.1 Power Up 1. Rotate the Power On-Off/Volume Control knob clockwise to power on the radio. The display illuminates when the radio powers up. 2. Wait for the power-up sequence to complete, which takes approximately ten (10) seconds. During this time, if enabled for auto registration, the radio is provisioned with a customized user personality designed for the user’s specific needs by the OpenSky network administrator.
PAGE 48
MM-014716-001, Rev. P If necessary, contact radio system administration personnel for login assistance and/or radio-specific login instructions. NOTE 6.5 LOG OFF THE NETWORK The *0## command de-registers the radio. Typically, this is automatically performed when powering down the radio. Using this method, the User ID is remembered by the radio so only the password is needed at next login. Manually log off by pressing *0## (requires System Model). 6.
PAGE 49
MM-014716-001, Rev. P 6.8 RADIO STATUS ICONS Status Icons indicate the various operating characteristics of the radio. The icons show operating modes and conditions (see Table 6-2). The location of icons on the display may vary depending on configuration. Table 6-2: Icons and Descriptions ICON DESCRIPTION Indicates data registration. Antenna Volume bars – above VOL text indicates relative volume level. RSSI indicator appears next to the Antenna icon. 6.
PAGE 50
MM-014716-001, Rev. P MESSAGE DESCRIPTION NOAUT05 MDIS failed mutual authentication. If condition persists in strong signal conditions, contact your system administrator. BADMDIS MDIS failed mutual authentication. If condition persists in strong signal conditions, contact your system administrator. MDS BSY MDIS busy – retry. UNK DOM Unknown home domain. If condition persists in strong signal conditions, contact your system administrator. KEYSYNC Mismatched key sequence number.
PAGE 51
MM-014716-001, Rev. P MESSAGE DESCRIPTION No App ECP/XGP mode is unavailable (not programmed). NO PRIV Missing required privilege. NO SYNC No forward-channel sync (weak or no coverage). If condition persists in strong signal conditions, contact your system administrator. No Access Incoming encrypted voice cannot be decrypted. If condition persists in strong signal conditions, contact your system administrator. NO REG Not registered with MDIS, VNIC, or both.
PAGE 52
MM-014716-001, Rev. P Profile 1 Profile 2 Profile 3 TG a TG d TG a TG b TG e TG d TG c TG f TG g TG x TG h TG y TG i TG z TG = Talk Group Figure 6-4: Personality Structure Example If Global Profile is enabled by the system administrator, the number of available talk groups to scan doubles. NOTE 6.11.2 Talk Groups A talk group represents a set of users that regularly need to communicate with one another. There can be any number of authorized users assigned to a talk group.
PAGE 53
MM-014716-001, Rev. P 6.12 ALERT TONES The XG-75M/M7300 radio also provides audible Alert Tones or “beeps” to indicate the various operating conditions (see Table 6-3). Table 6-3: XG-75M/M7300 OpenSky Mode Alert Tones NAME 52 TONE DESCRIPTION Call Queued 1 low tone/2 high tones Call queued for processing. Radio is out of coverage area or requested talk group is active. Sounds when resources become available for a call request placed in the queue (if enabled) upon channel access.
PAGE 54
MM-014716-001, Rev. P NAME TONE DESCRIPTION Priority Bump Single medium midpitched tone. Sounds when the current received call is preempted by a higher priority call. Site Found Tone Three short high-pitched tones. Sounds when the selected site is found using the Site Lock Menu. Site Not Found Tone Three short high-pitched tones. Sounds when the selected site is not found using the Site Lock Menu. 6.13 BASIC MENU STRUCTURE Table 6-4 illustrates the basic XG-75M/M7300 OpenSky menu structure.
PAGE 55
MM-014716-001, Rev. P MENU NAME RADIO DISPLAYS Display Brightness “Bright Menu” USAGE NOTES Use to dim or brighten. Press MENU to return to dwell display. , CLR, or OPT Side Tone Level “Side Menu” Use to choose side tone level (Off, Low, Med, or High). Press MENU to return to dwell display. , CLR, or OPT Intercom “INTERCOM” Use to turn intercom “On” or “Off.” Press MENU to return to dwell display.
PAGE 56
MM-014716-001, Rev. P MENU NAME RADIO DISPLAYS USAGE NOTES Profile Selection “ProfileMenu” Use to choose an available profile. Press MENU to return to dwell display. , CLR, or OPT Request to Talk Message Use to scroll through available messages. Press MENU to send the selected message. “RTT Msg” , CLR, or OPT Status Message Use “Status Msg” to scroll through available messages. Press MENU to send the selected message.
PAGE 57
MM-014716-001, Rev. P When a key on the DTMF keypad is pressed, the DTMF tone is played through the radio’s speaker. 6.15 KEYPAD 6.15.1 Keypad Commands (System Model Control Head) To perform a command from the keypad, press the * key followed by one of the pre-set function keys as follows: Table 6-5: Keypad Function Commands KEYPAD COMMAND 56 FUNCTION *0 Log off command: *0## (logs the user off the system). See page 47 for additional information.
PAGE 58
MM-014716-001, Rev. P 6.15.2 Quick Buttons (System Model Only) Quick Keys are a two-button sequence that gives the radio user quick access to certain menu items. Quick keys act as a toggle function. Table 6-6: Quick Button Functions QUICK KEYS 1# 2# 3# 4# FUNCTION Transition to ECP/XGP mode. If ECP/XGP is not loaded in the radio, the radio displays “No App.” Stealth Mode On/Off. Scan Mode On/Off.
PAGE 59
MM-014716-001, Rev. P 6.15.5 DTMF Overdial Using the keypad on a System Model, the radio can transmit DTMF tones corresponding to numbers/characters 0 - 9, *, and # on the keypad. To overdial numbers/characters, transmit by pressing and holding the PTT button and then, press the corresponding keys (one at a time) on the keypad. 6.16 CHANGE THE ACTIVE PROFILE The radio can store up to sixteen (16) standard profiles, one of which is the currently active profile. To change the currently active profile: 1.
PAGE 60
MM-014716-001, Rev. P 6.20 STEALTH MODE For some users, it is important to be able to turn off the radio’s display lights, button backlighting, volume and side tones, but not radio traffic. For example, in covert operations, lights and sounds could inadvertently expose an otherwise unobservable radio user. For this purpose, the radio has a Stealth feature that disables the radio display light, indicator light, and audible side tones.
PAGE 61
MM-014716-001, Rev. P 6.22 CHANGE OPERATING MODE 1. Scroll through the menu until “App Mode” appears in the bottom line of the display. 2. Use to choose an available mode. Press MENU and confirm (Y/N) with MENU again. and press Or Preset button C can be configured via programming to reboot the radio into a particular application mode. Or Quick Button command 1# transitions the radio to ECP/XGP mode. If ECP/XGP mode is not loaded in the radio, the radio displays “No App.” 6.
PAGE 62
MM-014716-001, Rev. P 6.23.2 Transmit a Voice Call Transmit a voice call as follows: 1. Turn the radio on. 2. If required, login to the network using a user ID and password (see Section 6.4). 3. Select the talk group on which you want to transmit. 4. Press and hold the Push-to-Talk (PTT) button on the hand-held microphone, pause for a moment, and then speak normally. For maximum clarity, hold the microphone approximately 2 inches from the mouth and do not shout or whisper into it.
PAGE 63
MM-014716-001, Rev. P CAUTION A user at a radio with only one control head/front panel can turn intercom mode on. In this case, pressing the microphone’s PTT button does NOT send microphone audio anywhere. 6.26 TALK GROUP LOCK OUT There are two ways of focusing voice communications by suppressing calls from talk groups in the currently active profile: 1. No Scan: By turning scan off (selecting “No Scan” via the “ScnModeMenu”), only the selected talk group is audible. 2.
PAGE 64
MM-014716-001, Rev. P 6.26.2 Unlock a Talk Group 1. Scroll through the menu until “LockOutMenu” appears in the bottom line of the display. The name of a talk group in the currently active profile appears in the top line. 2. Use to scroll through the list of talk groups, if any, until the talk group desired for unlocking appears in the top line of the display. A less-than symbol (“<”) appears next to the name of a talk group that is currently locked out. 3. Press the MENU button to unlock the talk group.
PAGE 65
MM-014716-001, Rev. P 6.27.1 Check or Change Active Scan Mode The currently active scan mode does not appear in the dwell display. To check it, access “ScnModeMenu” and observe it in the top line of the display. To change the active scan mode: 1. Scroll through the menu until “ScnModeMenu” appears in the display. 2. Use to scroll through the scan options until the desired mode appears. See Table 6-7. Or Use the quick button option 3#. 6.27.
PAGE 66
MM-014716-001, Rev. P 6.28 MAKE SELECTIVE CALLS Selective Calling is a feature that allows two radio units to obtain and utilize an independent voice path for a private call. Radios can be configured to both initiate and receive Selective Calls or to only receive Selective Calls. In the OpenSky system, a source radio can be configured to initiate Selective Calls through a preprogrammed list in memory.
PAGE 67
MM-014716-001, Rev. P 5. Press and release the PTT button to initiate the Selective Call request. When the called party accepts the call, press the PTT again and begin speaking. 6.28.2 Speed Dial a Selective Call NOTE Speed dial numbers are defined and provisioned by the OpenSky network administrator and cannot be manually entered into the radio by the user. Contact the administrator if changes to the speed dial list are required. 1.
PAGE 68
MM-014716-001, Rev. P 6.29.1 Send Selective Alert Messages The destination radio’s User ID can be selected via the menu or via the keypad on the system model control head. Menu Button Method: 1. Scroll through the menu until “AlertDest” (Alert Destination) appears in the bottom line of the display. The current speed dial number scrolls on the top line. 2. Use to change to a different speed-dial number. 3. When the desired speed-dial number appears, press the MENU button to activate the selection. 4.
PAGE 69
MM-014716-001, Rev. P STATUS MESSAGE Not Reg Partial Unauth Alrt Unknown Msg Unreachable DEFINITION Destination is not registered. Not all destination ESN instances reachable. Unauthorized service function; initiator is not authorized to send the selected service message. Unknown status received from VNIC. Alert destination cannot be reached. 6.29.
PAGE 70
MM-014716-001, Rev. P 4. Wait a few seconds and then press and release the mic’s PTT button to initiate the call. An initial ring tone plays indicating call initiation. Once the gateway picks up the call, another ring tone sounds. 5. When the caller answers, press the PTT button when speaking and release it to listen to the caller. 6. To hang-up, press the # button or (-) using . 6.30.2 Receive an Interconnect Call When receiving an Interconnect Call, a ring sounds in the speaker and/or headset.
PAGE 71
MM-014716-001, Rev. P If the attempt is unsuccessful, “E-PEND” flashes periodically and a retry is queued for 10 seconds. If unsuccessful because of lost sync, retry occurs immediately upon reacquiring sync. On each retry attempt, radio temporarily displays “E-RETRY.” This process repeats until the emergency is successfully declared. 6.31.
PAGE 72
MM-014716-001, Rev. P x If scan mode is set to “Normal” and the emergency was declared on the selected talk group, the selected/emergency talk group’s name remains in the top line of the display. Audio on the emergency talk group is heard in the speaker/headset. x If scan mode is set to “Normal” and the emergency was declared on a talk group other than the selected talk group, the emergency talk group’s name appears in the bottom line of the display.
PAGE 73
MM-014716-001, Rev. P are generated automatically by the system and provisioned to authorized users. This process requires that authorized users login to the network and be authenticated. Encryption keys require no manual handling and are never sent “in the clear” over any network interface or air-link. 1. “Pls Login” appears displayed in the bottom line of the dwell display. 2. Login normally using the keypad on a system model control head to enter User ID and Password.
PAGE 74
MM-014716-001, Rev. P If a secure (encrypted) call is in progress, and the user has not entered the key, the bottom of the dwell display alternates between “No Access” and the alias of the radio that is currently engaged in the secure call. Once the user has terminated manual encryption, “UnSecure” appears temporarily in the bottom line of the dwell display. 6.33 PRESET BUTTONS The front panel contains three buttons labeled A, B, and C.
PAGE 75
MM-014716-001, Rev. P 6.34.2 Send Status Message via the Menu 1. Scroll through the menu until “Status Msg” appears and press MENU. If no messages have been configured, “No Messages” is displayed. 2. Scroll through the available messages using the 1st line of the display. . The configured Status message is displayed on 3. Press the MENU button to send the currently selected message. If no messages have been configured, no message is sent and an error tone sounds.
PAGE 76
MM-014716-001, Rev. P 6.36 GPS COORDINATES The radio’s current latitude and longitude coordinates may be displayed using the “GPS” menu. The following procedure assumes a GPS antenna is connected to the radio and it is receiving adequate signals from GPS satellites: 1. Scroll through the menu until the “GPS” menu appears in the bottom line of the display. Current GPS coordinate latitude and longitude data continuously scrolls in the top line of the display in a degrees:minutes:seconds format. 2.
PAGE 77
MM-014716-001, Rev. P Use the Client Mode menu to return to normal operation (Network Mode). The personality and profile in use at the time the radio entered SOI mode is restored. Enter SOI Mode (System Model Only): 1. Press *4#. 2. The radio prompts for the channel. Enter the channel number and press # to confirm channel. 3. The radio prompts for the band. Enter the number assigned for the desired frequency band and press # to confirm. 4. The radio reverts to the dwell display.
PAGE 78
MM-014716-001, Rev. P 7. EDACS/CONVENTIONAL/P25 (ECP/XGP) OPERATION 7.1 TURN THE RADIO ON Rotate the POWER ON/OFF/VOLUME knob clockwise, out of detent to turn the radio on. A short beep (if enabled through programming) indicates the radio is ready for operation. The display indicates, if programmed, the last selected system name on line one and the last selected group or channel name on line two. NOTE NOTE 7.2 The radio can be programmed to require the entry of a PIN in order to operate the radio.
PAGE 79
MM-014716-001, Rev. P Figure 7-1: System Model Figure 7-2: Scan Model Button function may vary depending upon radio programming. Complete the table in Section 10 if the keys have been remapped to provide new functions. NOTE Table 7-1: Front Panel Default Controls and Functions PART Power OnOff/Volume Control knob FUNCTION Turn knob clockwise to power on the radio and increase volume. Turn counter-clockwise to decrease volume and power off the radio.
PAGE 80
MM-014716-001, Rev. P PART FUNCTION This rocker type button is used to display the current SCAN status for a group/channel and then add or delete the group/channel from the system scan list. The primary function of this rocker type button is to scroll through the System list or the Group/Channel list depending upon programming. The secondary function is to increment or decrement items within a list (phone list for example). OPT/OPTION Toggle a PC programmable feature ON and OFF.
PAGE 81
MM-014716-001, Rev. P 7.5 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. Figure 7-3: Typical Display Table 7-2: Icons and Descriptions ICON DESCRIPTION Indicates the EDACS system is in Failsoft™ mode (if enabled through programming). Indicates selected group or channel is in the scan list. Indicates selected group or channel is programmed as Priority 1 in scan list. Indicates selected group or channel is programmed as Priority 2 in scan list.
PAGE 82
MM-014716-001, Rev. P 7.6 MESSAGES During radio operation, various messages are displayed on either line 1 or line 2. Typical messages include control channel status information, such as system busy or call denied, or messages associated with the radio's operation, (i.e., volume adjust). These messages are described as follows: Table 7-3: Radio Messages MESSAGE NAME DESCRIPTION QUEUED Call Queued Indicates the system has placed the call in a request queue.
PAGE 83
MM-014716-001, Rev. P MESSAGE NAME DESCRIPTION PHONE Phone Call Displayed when a phone call is received from the site. It is displayed in line 1 of the display. Line 2 of the display contains the display *INDV* when line 1 contains this message. The radio interprets a received phone call as an individual call. CONV FS Conventional Failsoft Displayed when a failure of the EDACS system occurs. All communication is in conventional mode.
PAGE 84
MM-014716-001, Rev. P MESSAGE NAME DESCRIPTION KEY=1-7 Displayed on line 2 of the display in the display key mode of the menu for conventional systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and for trunked systems when the “SYS KEY” or “GRP KEY” is displayed in line 1. PRIMARY Displayed on line 1 of the display when the primary keys are enabled. PRS NAME Personality Name Displayed on line 1 of the display under the revision selection of the menu.
PAGE 85
MM-014716-001, Rev. P 7.8 MENU NOTE To directly access a menu, press the corresponding button on the control head. For example, press the SYS button to enter the System select mode. Button configuration may vary depending on radio programming. The order and specific number of menu items available is configurable through programming. Upon radio power up, the menu item at the beginning of the menu list is always displayed first.
PAGE 86
MM-014716-001, Rev. P FEATURE DISPLAY PARAMETER SETTINGS External Speaker Encryption Key Loading Display Current Encryption Key(s) Scan Private Mode Scan Add Scan Delete Menu item: EXT SPKR ON, OFF Menu item: KEYLOAD Up to 8 banks of 7 keys Scan Add/Delete Menu item: SCAN A/D Menu item: DISP KEY Menu item: SCAN Menu Item: PRIVATE Menu item: SCAN ADD Menu item: SCAN DEL COMMENT External Speaker is toggled ON and OFF. Enables the radio to accept the loading of encryption keys.
PAGE 87
MM-014716-001, Rev. P x Serial number ROM data - serial number of the ROM x Feature encryption data stream - used to enable features x Number Fields - defines limits x Features enabled - displays bit fields of enabled features 7.9.1 Serial Number ROM (12 Hex Digits) Example: To enable a feature in a radio, call Harris and provide them with the ROM serial number. The serial number shown here is for example only. 7.9.
PAGE 88
MM-014716-001, Rev. P x CH# XXX - Maximum number of conventional channels available The user needs to know the limits of the radio before attempting to enable other features. The numbers shown here are for example only. 7.9.3 Features Enabled These numbers indicate which features are enabled. Example: Table 7-6 lists possible features available in the user's radio.
PAGE 89
MM-014716-001, Rev. P 7.10 VOICE ANNUNCIATION When enabled via programming, the Voice Annunciation feature provides audible feedback for various radio operations. The radio can be programmed to play an audio message for any or all of the following. This message can be a pre-recorded (canned) message or a user-recorded message.
PAGE 90
MM-014716-001, Rev. P METHOD 1: If group selection is programmed to the SYSTEM/GROUP/CHANNEL knob, select a group by turning the SYSTEM/GROUP/CHANNEL knob to the desired group. The display registers the new group name on line 2. If the wrap option is OFF and the knob is moved to a position greater than the number of programmed groups, the highest programmed group remains selected.
PAGE 91
MM-014716-001, Rev. P Table 7-7: Current Cryptographic Key Display ENCRYPTION KEY DISPLAYED MESSAGE DISPLAYED System "SYS KEY" "KEY = 1" Group/Channel "GRP KEY"/"CHN KEY" "KEY = 2"/KEY = 2" 7.13.2 Key Zero All cryptographic keys can be zeroed (erased from radio memory) by pressing and holding the CLR/CLEAR button, and while still pressing this button, press and hold the OPT/OPTION button. Press both buttons for 2 seconds.
PAGE 92
MM-014716-001, Rev. P 7.14 MACRO KEY OPERATION Macro key operation permits the user to accomplish a series of keystrokes with a single "macro" keystroke. Up to ten (10) macro keys can be defined, each capable of executing up to twenty (20) keystrokes, to any pushbutton input (i.e., keypad keys, buttons, etc.). Each macro key can be preprogrammed to activate when pressed or when released. A macro key can also be pre-programmed to change the keystroke sequence the next time the macro key is activated.
PAGE 93
MM-014716-001, Rev. P activity on the channel during conventional failsoft operation may be noticed, so be careful not to transmit until the channel is clear. Operation during conventional failsoft is the same as operation on a conventional system, except that it is not possible to select a communications channel, or use emergency and special call. When trunking is restored, the radio is automatically returned to normal operation. Emergency and Special Call are not operational during conventional failsoft.
PAGE 94
MM-014716-001, Rev. P 7.19 MIXED SYSTEM ZONES A Zone is a grouping of analog conventional channels, P25 conventional channels, and/or P25T or P25C talkgroups. Mixed System Zones are defined in RPM and can be comprised of any combination of channels/groups from multiple systems as long as the system definitions share the same WACN/System ID. If a Mixed System Zone is not configured in RPM, it will not appear on the radio. Up to 50 Mixed System Zones can be defined. To select a Mixed System Zone: 1.
PAGE 95
MM-014716-001, Rev. P 7.22 SYSTEM SCAN OPERATION (EDACS AND P25 TRUNKED) The radio can be programmed with the following System Scan features. These features are automatically enabled upon radio power up. A key or menu option is also defined to allow the System Scan features to be toggled during radio operation. This is covered in the Menu Selection and Pre-Programmed Keypad Key sections. The System Scan state is maintained through system changes but defaults to ON at power up. 7.22.
PAGE 96
MM-014716-001, Rev. P 7.22.6 Menu Selection Press MENU and then use the ramp control to scroll through the selections until SYS SCAN is displayed. Then press MENU to toggle the System Scan state. The SYSC ON or SYSC OFF display message is displayed for two seconds to show the new state. 7.22.7 Pre-Programmed Keypad Key Press the pre-programmed key and the SYSC ON or SYSC OFF display message is displayed for two seconds to show the new state. 7.
PAGE 97
MM-014716-001, Rev. P 5. Press (+) with line 1. a third time to set the group/channel to Priority 1. is displayed in column 1, The priority level selection sequence only advances the group to the next higher priority level and stops at priority level 1. To select a lower priority level, the group/channel must be deleted from the scan list and then added back to the scan list. Each new group/channel added to the scan list starts at the lowest priority.
PAGE 98
MM-014716-001, Rev. P 7.23.5 Priority Group/Channel Scanning When scan is enabled and the Priority 1 and Priority 2 groups/channels have been identified, the radio listens to calls on those groups/channels and the selected group/channel. While receiving a scanned call, the radio continues to monitor the selected Priority 1 and Priority 2 group/channel and drops the call if the selected group/channel or other higher priority call becomes active.
PAGE 99
MM-014716-001, Rev. P 2. Select the desired group/channel from the Custom Scan list. channel/group include: x View the channel’s/group’s scan priority. x Delete the channel/group from the scan list. x Nuisance delete the channel/group. Options available for each 3. Press the Option button to back up one display; press the Clear button to return to the home screen. 7.23.7.3 Edit Custom Scan Lists Scan must be off to edit a Custom Scan List. NOTE 1. From the radio menu, select CUSTSCAN. 2.
PAGE 100
MM-014716-001, Rev. P To respond after the call-back time-out, press the IND key. The radio's display shows the callers ID on the first line and WHCI=1 on the second line. Pressing the PTT button at this point initiates an individual call back to the original caller. (If the last call was a group call, the display shows WHCG=1. Pressing the PTT button places the call as an individual call.) The radio stores the IDs of the last 10 callers in the Calls Received List as shown.
PAGE 101
MM-014716-001, Rev. P 1. To select a previously stored individual, select the I-Call mode from the menu or press IND followed by the ramp control to scroll through the list of stored individuals. While in the individual call list, the MENU key toggles the display between the call name and the unit ID number. If the individual is not stored in this list but the individual’s unit ID is known, it can be entered directly from the keypad. 2. Press the PTT button.
PAGE 102
MM-014716-001, Rev. P NOTE The XG-75M/M7300 Series mobile radio is capable of half-duplex conversation only. The caller’s message can only be sent if the PTT button is pressed (the radio is transmitting) and the caller can only be heard by the person being called when the PTT is released (the radio is receiving). 7.26.
PAGE 103
MM-014716-001, Rev. P 4. Press and hold MENU until the display changes indicating that the number has been stored. 5. Repeat the steps above if the number stored in an entry location needs to be changed. 7.27 MOBILE DATA (EDACS AND P25 TRUNKED) The XG-75M/M7300 Series mobile radios, when operating in the EDACS or P25 Trunked configuration, permit either voice or data calls to be transmitted or received.
PAGE 104
MM-014716-001, Rev. P 7.27.4 Exiting Data Calls Under normal conditions, the radio enters the scan lockout mode and returns to the control channel after completion of a data call (transmit or receive). If, during a data call, one of the following conditions occurs, the data call is immediately terminated and the radio performs the desired function: x PTT is activated. x The PTT is in Public Address Mode. x An emergency is declared by pressing the pre-programmed emergency button.
PAGE 105
MM-014716-001, Rev. P the Scan version, the four primary keycaps must be reconfigured and pre-programmed for status/message operation. 7.28.1 Status Operation Status operation permits the transmission of a pre-programmed status condition to an EDACS or P25 Trunked site. To send a status condition, press the STS button and then press one of the number buttons (0-9) to select the pre-programmed status.
PAGE 106
MM-014716-001, Rev. P 7.29 EDACS CONVENTIONAL P1 SCAN This feature permits the radio user to scan a pre-programmed conventional system and channel as a Priority 1 (P1) channel while the radio is selected for EDACS trunked system. If activity is detected on the conventional P1 channel, the radio unmutes and remains on this conventional channel for the programmable hang time. The radio must be pre-programmed to designate a button for scan ON/OFF operation. 7.
PAGE 107
MM-014716-001, Rev. P NOTE When the squelch adjust feature is activated, Channel Guard, T99 decode, and Scan are disabled. When the squelch adjust feature is exited, Channel Guard, T99 decode, and Scan are restored to their previous states. 7.32.1 Menu Selection 1. Press the MENU key and then use the ramp control SQUELCH is displayed. Then press MENU again. to scroll through the selections until 2. The display shows SQLCH=xx, where "xx" is the value between 1 and 16. 3.
PAGE 108
MM-014716-001, Rev. P Type 99 is automatically disabled when Scan is enabled. NOTE 7.33.1 Menu Selection Press MENU and then use the ramp control to scroll through the selections until T99 ENAB is displayed. Then press MENU to toggle the Type 99 decode state. The T99 ON or T99 OFF display message is displayed for two seconds to show the new state. 7.33.2 Pre-Programmed Keypad Key Press the pre-programmed key and the T99 ON or T99 OFF display message is displayed for two seconds to show the new state. 7.
PAGE 109
MM-014716-001, Rev. P 7.36 AUDIO PLAYBACK Every call received by the radio is recorded in internal memory, overwriting the last recorded call. When the PLAYBACK key is pressed, the last recording is replayed and any future recordings are stopped. Pressing PLAYBACK again repeats the same recorded call. Pressing and holding the PLAYBACK key until the tone sounds erases the recording and starts the recording of incoming calls again.
PAGE 110
MM-014716-001, Rev. P 7.37.4 Display Current Time Select TIME with the MENU key to retrieve the current date and time. 7.38 VIEW GPS INFORMATION If the M7300 is equipped with the optional GPS receiver module, you can view your position and satellite information via the GPS Menu. GPS requires an unobstructed view of the sky and the signal is greatly diminished inside buildings, tunnels, heavily forested areas, etc. GPS may not work at all under some conditions, especially in metal enclosures or buildings.
PAGE 111
MM-014716-001, Rev. P 8. BASIC TROUBLESHOOTING If the radio is not operating properly, check Table 8-1 for likely causes. For additional assistance, contact a qualified service technician. Table 8-1: Basic Troubleshooting SYMPTOM 110 CAUSE SOLUTION Radio will not turn on. No power. Test the connection to the vehicle power supply. Radio will not turn off. If in multiple control head configuration, one of the attached control heads is still powered up. Power off all control heads.
PAGE 112
MM-014716-001, Rev. P 9. CUSTOMER SERVICE 9.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
PAGE 113
MM-014716-001, Rev. P 10. KEYPAD REMAPPING If the keys have been remapped to provide new functions, fill in the following template for future reference.
PAGE 114
MM-014716-001, Rev. P 11.
PAGE 115
MM-014716-001, Rev.
PAGE 116
MM-014716-001, Rev.
PAGE 117
MM-014716-001, Rev. P SYSTEM NUMBER SYSTEM NAME TRK/CNV GRP/CHN NUMBER GRP/CHN NAME USE 12. WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at the Customer Care center webpage: http://www.pspc.harris.com/Service/Customerservice.aspx.
PAGE 118
MM-014716-001, Rev. P APPENDIX A - CONFIGURING ENCRYPTION A.
PAGE 119
MM-014716-001, Rev. P b. Scroll through the menu to select the KEYLOAD option and press the MENU button to activate. c. Scroll through and select the HKL option and press the MENU button. The radio can now accept keys from the Harris Keyloader. 5. Load the UKEK file from the Crypto Officer onto the PC. 6. Run the RPM application and setup the radio’s Personality according the SLN Binding Report information. 7. Setup the talk groups and the SLN mappings (Talk Group ID to SLN).
PAGE 120
MM-014716-001, Rev. P 10. Select the serial port that you have connected to the radio. 11. Enter into Harris Keyload Mode (HKL). a. Press the radio’s MENU button. b. Scroll through the menu to select the KEYLOAD option and press the MENU button to activate. c. Scroll through and select the HKL option and press the MENU button. The radio can now accept keys from the Harris Keyloader. 12. Select Radio from the drop-down and click Load. 13. Click Finish. A.1.2.3 Power on the Motorola KVL Device 1.
PAGE 121
Public Safety and Professional Communications | www.pspc.harris.
PAGE 122
Operator’s Manual MM-012125-001 Rev.
PAGE 123
MM-012125-001, Rev. M REV A DATE Sep/07 Feb/08 B Sep/08 C D E Jul/09 Apr/10 Dec/10 F Apr/11 G H J Aug/11 Oct/12 Jul/13 K Apr/14 L M Oct/14 Apr/15 MANUAL REVISION HISTORY REASON FOR CHANGE Initial Release. Updated OpenSky operation. Added quick buttons, new CH-721 keymap, keypad lock/unlock, error messages, updated status call and status alert messages. Harris conversion. Added keypad lock/unlock instructions for EDACS and Conventional modes. Updated antenna info, added P25 and encryption.
PAGE 124
MM-012125-001, Rev. M TABLE OF CONTENTS Page 1. REGULATORY AND SAFETY INFORMATION............................................................................. 9 1.1 SAFETY SYMBOL CONVENTIONS ......................................................................................... 9 1.2 REGULATORY APPROVALS ................................................................................................. 10 1.2.1 Applicable Type Acceptance/Certification Numbers ...............................................
PAGE 125
MM-012125-001, Rev. M TABLE OF CONTENTS 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 4 Page POWER UP AND VOLUME CONTROL ................................................................................. 37 5.2.1 Power Up ....................................................................................................................... 37 5.2.2 Volume Control .........................................................
PAGE 126
MM-012125-001, Rev. M TABLE OF CONTENTS 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 6. Page 5.28.3 Receive a Selective Call ................................................................................................ 57 5.28.4 Terminate a Selective Call ............................................................................................. 57 SELECTIVE ALERT.................................................................................................................. 57 5.29.
PAGE 127
MM-012125-001, Rev. M TABLE OF CONTENTS 6.14 6.15 6.16 6.17 6.18 6.19 6.20 6.21 6.22 6.23 6.24 6.25 6.26 6.27 6 Page 6.13.1 Displaying the Currently Used Cryptographic Key Number ......................................... 80 6.13.2 Key Zero ........................................................................................................................ 80 6.13.3 Receive an Encrypted Call............................................................................................. 80 6.13.
PAGE 128
MM-012125-001, Rev. M TABLE OF CONTENTS 6.28 6.29 6.30 6.31 6.32 6.33 6.34 6.35 6.36 6.37 6.38 Page STATUS/MESSAGE OPERATION (EDACS AND P25 TRUNKED) ..................................... 95 6.28.1 Status Operation ............................................................................................................ 95 6.28.2 Message Operation ........................................................................................................ 95 EDACS CONVENTIONAL P1 SCAN .....................
PAGE 129
MM-012125-001, Rev. M TABLE OF CONTENTS Page transmission branchée sur une radio mobile ......................................................................... 25 Tableau 2-4: Distance latérale sécuritaire minimale recommandée d’une antenne de transmission branchée sur une radio Motocyclette ............................................................... 29 Table 5-1: Front Panel Default Controls and Functions ..........................................................................
PAGE 130
MM-012125-001, Rev. M 1. REGULATORY AND SAFETY INFORMATION 1.1 SAFETY SYMBOL CONVENTIONS The following conventions are used in this manual to alert the user to general safety precautions that must be observed during all phases of operation, installation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere violates safety standards of design, manufacture, and intended use of the product.
PAGE 131
MM-012125-001, Rev. M 1.2 REGULATORY APPROVALS 1.2.1 Applicable Type Acceptance/Certification Numbers Table 1-1: FCC Type Acceptance RADIO PART NUMBER FCC TYPE ACCEPTANCE NUMBER FREQUENCY RANGE/WATTAGE RU-144750-061 (Rev. K or earlier) 764-806 MHz, 30 Watt 806-870 MHz, 35 Watt OWDTR-060-E RU-144750-061 (Rev.
PAGE 132
MM-012125-001, Rev. M brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 1.4 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS Before using the two-way mobile radio, review the following important RF energy awareness and control information and operational instructions.
PAGE 133
MM-012125-001, Rev. M 1.5 COMPLIANCE WITH RF EXPOSURE STANDARDS The M5300 series two-way mobile radios are designed and tested to comply with a number of national and international standards and guidelines regarding human exposure to RF electromagnetic energy. The radios comply with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty-cycle times of up to 50% (50% transmit, 50% receive) and it is authorized by the FCC for occupational use.
PAGE 134
MM-012125-001, Rev. M 1.5.3 Mobile Antennas (Vehicle Installations) Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 9.8 Inches (25 Centimeters) 21.
PAGE 135
MM-012125-001, Rev. M Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT 14 ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 11.8 Inches (30 Centimeters) 23.6 Inches (60 Centimeters) 9.8 Inches (25 Centimeters) 21.
PAGE 136
MM-012125-001, Rev.
PAGE 137
MM-012125-001, Rev. M Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT * 16 ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 900 MHz AN102800V1 (Discontinued) 136 – 941 MHz Standard Rooftop-Mount; ¼-Wave Unity-Gain** 20 inches (51 centimeters) 44.
PAGE 138
MM-012125-001, Rev. M 1.5.4 Mobile Antennas (Motorcycle Installations) Table 1-4: Rated Power and Recommended Minimum Safe Lateral Distance (Motorcycle Installation) MAX.
PAGE 139
MM-012125-001, Rev. M 1.7 COMMON HAZARDS The operator of any mobile radio should be aware of certain hazards common to the operation of vehicular radio transmissions. Possible hazards include but are not limited to: x Explosive Atmospheres — Just as it is dangerous to fuel a vehicle while its engine is running, be sure to turn the radio OFF while fueling the vehicle. If the radio is mounted in the trunk of the vehicle, DO NOT carry containers of fuel in the trunk.
PAGE 140
MM-012125-001, Rev. M 1.8 SAFE DRIVING RECOMMENDATIONS The American Automobile Association (AAA) advocates the following key safe driving recommendations: 1.9 x Read the literature on the safe operation of the radio. x Keep both hands on the steering wheel and the microphone in its hanger whenever the vehicle is in motion. x Place calls only when the vehicle is stopped. x When talking from a moving vehicle is unavoidable, drive in the slower lane. Keep conversations brief.
PAGE 141
MM-012125-001, Rev. M x The FCC requires self-identification at certain specific times by means of call letters. Refer to the rules that apply to the particular type of operation for the proper procedure. x No changes or adjustments shall be made to the equipment except by an authorized or certified electronics technician. 1.
PAGE 142
MM-012125-001, Rev. M 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit.
PAGE 143
MM-012125-001, Rev. M Tableau 2-2: Type de Canada Industrie Acceptation NUMÉRO DE PIÈCE DE LA RADIO RU-144750-061 (Rev. K or earlier) RU-144750-061 (Rev. L or later) RU-144750-181 FRÉQUENCE RADIO/WATTAGE 764-806 MHz, 30 Watt 806-870 MHz, 35 Watt 764-806 MHz, 30 Watt 806-870 MHz, 35 Watt 900 MHz, 30 Watt CANADA INDUSTRIE TYPE NOMBRE ACCEPTATION 3636B-0051 3636B-0132 3636B-0049 Reglement applicables d'Industrie Canada: RSS 119; RSS 210 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES 2.3.
PAGE 144
MM-012125-001, Rev. M Cette radio bidirectionnelle utilise une énergie électromagnétique dans le spectre des radiofréquences (RF) pour permettre une communication à distance entre deux utilisateurs ou plus. Elle utilise l’énergie des RF ou les ondes radio pour envoyer et recevoir des appels. L’énergie des RF est une forme d’énergie électromagnétique. D’autres formes comprennent, entre autres, l’énergie électrique, la lumière du soleil et les rayons X.
PAGE 145
MM-012125-001, Rev. M x x x American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95.1-2005. Institute of Electrical and Electronic Engineers (IEEE) C95.1-2005. IC Standard RSS-102, numéro 4, 2010 : Spectrum Management and Telecommunications Radio Standards Specification. Radiofrequency Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands).
PAGE 146
MM-012125-001, Rev. M 2.5.
PAGE 147
MM-012125-001, Rev.
PAGE 148
MM-012125-001, Rev.
PAGE 149
MM-012125-001, Rev.
PAGE 150
MM-012125-001, Rev. M 2.5.4 Monté Antennes (Motocyclette) Tableau 2-4: Distance latérale sécuritaire minimale recommandée d’une antenne de transmission branchée sur une radio Motocyclette RF BAND NUMÉRO DE PIÈCE DE L’ÉLÉMENT DE L’ANTENNE DESCRIPTION DE L’ANTENNE DISTANCE MINIMALE RECOMMANDÉE DE L’ANTENNE DE TRANSMISSION POUR LE CORPS HUMAIN MAX. TX PUISSANCE (Watts) ENVIRONNEMENT ENVIRONNEMENT CONTRÔLÉ NON CONTRÔLÉ 800 MHz 700 or 800 MHz LE-OM806HDBKTNCDS 800 MHz -monture; gain de 3.
PAGE 151
MM-012125-001, Rev. M x Ne tentez pas d’apporter une modification non autorisée à la radio. Des changements ou des modifications à la radio peuvent causer une interférence nocive ou entraîner un dépassement des limites d’exposition aux RF de la FCC. Seul le personnel qualifié doit utiliser la radio. x Utilisez toujours seulement des accessoires autorisés (antennes, haut-parleurs/micros, etc.).
PAGE 152
MM-012125-001, Rev. M ¾ L'emplacement qui abrite la radio doit être isolé et scellé de l'emplacement contenant le réservoir de GLP et ses raccords. ¾ Des raccords de remplissage extérieurs doivent être utilisés pour le réservoir de GLP. ¾ Le réservoir de GLP doit être pourvu d'une évacuation vers l'extérieur du véhicule x 2.
PAGE 153
MM-012125-001, Rev. M x La loi interdit l'envoi de faux indicatifs d'appel ou de faux messages de détresse ou d'urgence. La FCC exige que vos conversations soient brèves et s'en tiennent au sujet de l'appel. Pour gagner du temps, utiliser autant que possible des messages codés. x L'utilisation de la radio pour l'envoi de messages personnels (sauf en cas d'urgence) constitue une violation des règles de la FCC. Envoyer des messages essentiels uniquement.
PAGE 154
MM-012125-001, Rev. M 3. PRODUCT DESCRIPTION Designed to meet the critical demands of utility and public service users, the M5300 mobile provides the latest in digital radio technology. The M5300 mobile supports multiple operating modes, including OpenSky® digital trunked operation, Enhanced Digital Access Communications System (EDACS®) or ProVoiceTM trunked modes, P25 digital trunked mode, P25 digital conventional mode, and analog conventional mode.
PAGE 155
MM-012125-001, Rev. M 4. CHANGE OPERATING MODE 4.1 CHANGE FROM OTP MODE To change from OTP operating mode to EDACS, P25, Conventional (ECP/XGP): 1. Use , CLR, or OPT to cycle through the menu until the “Mode Menu” appears in the bottom line of the display. 2. Use to choose an available mode. Press MENU and confirm (Y/N) with MENU again. and press 3. Press the MENU button to confirm. Or Preset button C can be configured via programming to reboot the radio into a particular application mode.
PAGE 156
MM-012125-001, Rev. M 5. OPENSKY OPERATION 5.1 CH-721 FRONT PANEL COMPONENTS The front panel of the control head includes a dot matrix display, controls for menu navigation, an emergency button, three pre-set buttons, a power button/rotary volume dial, and a microphone connector. In addition, the system model control head features a DTMF keypad. Table 5-1 lists all default front panel controls and their functions.
PAGE 157
MM-012125-001, Rev. M NOTE Button function may vary depending upon radio programming. Any non-DTMF button can be configured to various functions via the at**chkeymap command. Refer to the AT command manual (MM-016649-001) for all possible events. Table 5-1 describes the default configuration. Table 5-1: Front Panel Default Controls and Functions PART FUNCTION Power OnOff/Volume Control Knob Turn knob clockwise to power on the radio and increase volume.
PAGE 158
MM-012125-001, Rev. M PART FUNCTION Toggles the Scan Mode ON/OFF. SCAN x If the Scan Mode is Normal and the Scan Mode is toggled Off, when the Scan Mode is toggled On the Scan Mode is set to Normal. x If the Scan Mode is Fixed and the Scan Mode is toggled Off when the Scan Mode is toggled On the Scan Mode is set to Fixed. x If the Scan Mode is Off when the radio boots up when the Scan Mode is toggled On the Scan Mode is set to Normal. 5.2 POWER UP AND VOLUME CONTROL 5.2.1 Power Up 1.
PAGE 159
MM-012125-001, Rev. M x If the radio is configured for alpha-numeric passwords and the password has consecutive duplicate numbers (“MES33” for example), enter # between the consecutive duplicate numbers so the radio does not interpret the entry as a letter (“D” in this example). x If the radio is configured for numeric-only passwords, do not enter # between duplicated numbers. 5. Press the # key twice for alphanumeric passwords or once for numeric-only passwords.
PAGE 160
MM-012125-001, Rev. M Figure 5-3: Typical Display 5.8 RADIO STATUS ICONS Status Icons indicate the various operating characteristics of the radio. The icons show operating modes and conditions (see Table 5-2). The location of icons on the display may vary depending on configuration. Table 5-2: Icons and Descriptions ICON DESCRIPTION Indicates data registration. Antenna Volume bars – above VOL text indicates relative volume level. RSSI bars appear to the right of the antenna icon. 5.
PAGE 161
MM-012125-001, Rev. M 40 MESSAGE DESCRIPTION UNAUTH5 Unsupported authentication. If condition persists in strong signal conditions, contact your system administrator. MDISBSY The MDIS is busy. If condition persists in strong signal conditions, contact your system administrator. DUP IP Duplicate IP. BADIKEY Invalid infrastructure public key sequence number (IPKSN). BADEKEY Invalid end-system public key sequence number (EPKSN). UNK MES Unknown mobile end system (MES).
PAGE 162
MM-012125-001, Rev. M MESSAGE DESCRIPTION NOSUPRT The MES cannot support the required provision. If condition persists in strong signal conditions, contact your system administrator. NOAUTHV VNIC does not support or failed mutual authentication. If condition persists in strong signal conditions, contact your system administrator. PLS LOGIN If enabled and authorized for encryption, the radio requires the user to enter a User ID and password. Login with keypad.
PAGE 163
MM-012125-001, Rev. M Profile 1 Profile 2 Profile 3 TG a TG d TG a TG b TG e TG d TG c TG f TG g TG x TG h TG y TG i TG z TG = Talk Group Figure 5-4: Personality Structure Example If Global Profile is enabled by the system administrator, the number of available talk groups to scan doubles. NOTE 5.11.2 Talk Groups A talk group represents a set of users that regularly need to communicate with one another. There can be any number of authorized users assigned to a talk group.
PAGE 164
MM-012125-001, Rev. M 5.12 ALERT TONES The M5300 radio also provides audible Alert Tones or “beeps” to indicate the various operating conditions (see Table 5-3). Table 5-3: M5300 OpenSky Mode Alert Tones NAME Call Queued TONE 1 low tone/2 high tones DESCRIPTION Call queued for processing. Radio is out of coverage area or requested talk group is active. Sounds when resources become available for a call request placed in the queue (if enabled) upon channel access.
PAGE 165
MM-012125-001, Rev. M NAME TONE DESCRIPTION Site Found Tone Three short high-pitched tones. Sounds when the selected site is found using the Site Lock Menu. Site Not Found Tone Three short high-pitched tones. Sounds when the selected site is not found using the Site Lock Menu. 5.13 BASIC MENU STRUCTURE Table 5-4 illustrates the basic M5300 OpenSky menu structure. Menu items vary depending upon system programming, radio hardware, and optional configurations.
PAGE 166
MM-012125-001, Rev. M MENU NAME RADIO DISPLAYS USAGE NOTES Side Tone Level “Side Menu” Use to choose side tone level (Off, Low, Med, or High). Press MENU to return to dwell display. , CLR, or OPT Intercom “INTERCOM” Use to turn intercom “On” or “Off.” Press MENU to return to dwell display. , CLR, or OPT See Next Page See Previous Page Selected Channel “ChannelMenu” Allows the user to display and change the current channel. Press MENU to return to dwell display.
PAGE 167
MM-012125-001, Rev. M MENU NAME RADIO DISPLAYS Request to Talk Message “RTT Msg” Status Message USAGE NOTES Use to scroll through available messages. Press MENU to send the selected message. , CLR, or OPT “Status Msg” Use to scroll through available messages. Press MENU to send the selected message. , CLR, or OPT Talk group Selection Use to choose a talk group in current profile. Press MENU to return to dwell display.
PAGE 168
MM-012125-001, Rev. M 5.15 KEYPAD 5.15.1 Keypad Commands (System Model Control Head) To perform a command from the keypad, press the * key followed by one of the pre-set function keys as follows: Table 5-5: Keypad Function Commands KEYPAD COMMAND FUNCTION *0 Log off command: *0## (logs the user off the system). See page 38 for additional information. *1 Login command: *1 # # (required for encryption). See page 37 for additional information. *2 Status Message: *2 <0...9> #.
PAGE 169
MM-012125-001, Rev. M 5.15.2 Quick Buttons (System Model Control Head Only) Quick Keys are a two-button sequence that gives the radio user quick access to certain menu items. Quick keys act as a toggle function. Table 5-6: Quick Button Functions QUICK KEYS 1# 2# 3# 4# 5# 7# 8# FUNCTION Transition to ECP/XGP mode. If ECP/XGP is not loaded in the radio, the radio displays “No App.” Stealth Mode On/Off. Scan Mode On/Off.
PAGE 170
MM-012125-001, Rev. M 5.15.5 DTMF Overdial Using the keypad on a System Model, the radio can transmit DTMF tones corresponding to numbers/characters 0 - 9, *, and # on the keypad. To overdial numbers/characters, transmit by pressing and holding the PTT button and then press the corresponding keys (one at a time) on the keypad. 5.16 CHANGE THE ACTIVE PROFILE The radio can store up to sixteen (16) standard profiles, one of which is the currently active profile. To change the currently active profile: 1.
PAGE 171
MM-012125-001, Rev. M 5.20 STEALTH MODE For some users, it is important to be able to turn off the radio’s display lights, button backlighting, volume and side tones, but not the radio traffic. For example, in covert operations, lights and sounds could inadvertently expose an otherwise unobservable radio user. For this purpose, the radio has a Stealth feature that disables the radio display light, indicator light, and audible side tones.
PAGE 172
MM-012125-001, Rev. M 5.22 CHANGE OPERATING MODE 1. Scroll through the menu until “App Mode” appears in the bottom line of the display. 2. Use to choose an available mode. Press MENU and confirm (Y/N) with MENU again. and press Or Preset button C can be configured via programming to reboot the radio into a particular application mode. Or Quick Button command 1# transitions the radio to ECP/XGP mode. If ECP/XGP mode is not loaded in the radio, the radio displays “No App.” 5.
PAGE 173
MM-012125-001, Rev. M 5.23.2 Transmit a Voice Call Transmit a voice call as follows: 1. Turn the radio on. 2. If required, login to the network using a user ID and password (see Section 5.4). 3. Select the desired talk group for transmitting on. 4. Press and hold the Push-to-Talk (PTT) button on the hand-held microphone, pause for a moment, and then speak normally. For maximum clarity, hold the microphone approximately 2 inches from the mouth and do not shout or whisper into it.
PAGE 174
MM-012125-001, Rev. M 5.26 TALK GROUP LOCK OUT There are two ways of focusing voice communications by suppressing calls from talk groups in the currently active profile: 1. No Scan. By turning scan off (selecting “No Scan” via the “ScnModeMenu”), only the selected talk group is audible. 2. Lock Out. By locking out selected talk groups, the “chatter” of the locked out talk groups cannot be heard. This focuses the user’s scanning resources to calls only on desired talk groups.
PAGE 175
MM-012125-001, Rev. M 2. Use to scroll through the list of talk groups, if any, until the talk group desired for unlocking appears in the top line of the display. A less-than symbol (“<”) appears next to the name of a talk group that is currently locked out. 3. Press the MENU button to unlock the talk group. The less-than symbol (“<”) next to the name of the talk group disappears. The dwell display appears as soon as the radio acknowledges the selection.
PAGE 176
MM-012125-001, Rev. M 5.27.2 Scan Priority The following lists the scanning priority order (from highest to lowest): x System All Call x Selected talk group in emergency state x Default emergency group in emergency state x Selected talk group x Emergency capable group in emergency state x Priority 1 talk group x Priority 2 talk group x Priority 3 talk group x Other (non-priority) 5.27.
PAGE 177
MM-012125-001, Rev. M Selective Call number without using the speed dial feature requires a system model control head (Figure 5-1). See Section 5.14 for more detail. Selective calls are terminated if an emergency is declared. The network limits Selective Calls to ten (10) minutes maximum. NOTE Table 5-8 lists and defines the messages that may be displayed by the radio during a Selective Call.
PAGE 178
MM-012125-001, Rev. M 3. Press and release the PTT button to ring the other user. a. The ring tone is sounded. b. If the other user accepts the call, the called user’s alias appears in the initiating caller’s display. The two are now in a private call until one ends the call, the call is terminated due to an initiated emergency, or the maximum time limit of ten (10) minutes is reached. 4. To end the call, press the # button or (-) using . 5.28.
PAGE 179
MM-012125-001, Rev. M 1. Press *7 on the keypad. “AlertDest” appears in the display. 2. Enter the number of the destination radio (e.g., 027-001-0006) using the DTMF keypad. If the region number (first 3 digits; 027 in this example) is the same as this radio’s region number, these digits do not need to be entered. Likewise, if the region and agency numbers (first 6 digits; 027-001 in this example) are the same as this radio’s numbers, these digits do not need to be entered.
PAGE 180
MM-012125-001, Rev. M Display Received Messages 1. Scroll through the menu until “AlertsRecvd” (Alerts Received) appears in the bottom line of the display. “No alerts” or the last received (newest) message appears in the display. It is preceded by the time the message was received, and the sender’s name/alias. 2. View other received messages using . 3. To delete the message currently being viewed, press the MENU button. Delete Received Messages To delete a received message: 1. Display the message. 2.
PAGE 181
MM-012125-001, Rev. M 5.31 EMERGENCY COMMUNICATIONS The M5300 mobile radio can transmit both emergency voice calls and emergency alerts over the entire network. OpenSky handles emergency calls and alerts with the highest priority. For critical voice communications, an emergency call can be raised on the default talk group or the currently selected talk group by “declaring” an emergency on the talk group. The exact talk group is determined by the currently active profile.
PAGE 182
MM-012125-001, Rev. M 5.31.3 Clear an Emergency Call or Alert Check with the system administrator to ensure that the radio is programmed to allow an emergency to be cleared. NOTE If enabled via programming, clear an emergency by: 1. Pressing and holding the CLR/CLEAR button and simultaneously pressing the emergency button. 2. After the Emergency Cleared Tone sounds, release both buttons. If the radio is in Stealth Mode, clearing the emergency takes the radio out of Stealth Mode. NOTE 5.31.
PAGE 183
MM-012125-001, Rev. M 5.31.5 Dismiss an Emergency Call An emergency is dismissed for a configurable amount of time only (default = 5 minutes). NOTE To ignore an emergency call declared by another radio user: 1. Scroll through the menu until “EmgDismiss” appears in the display. 2. Press until the talk group in the emergency state appears, as indicated by an asterisk (*) following the talk group’s name. 3. Press the MENU button. The emergency dismiss timer is cleared when the emergency is cleared. NOTE 5.
PAGE 184
MM-012125-001, Rev. M 5.32.2 Manual Encryption (System Model) Two or more users can manually encrypt a call, if enabled, without an established encrypted talk group. A pre-determined key is required at each radio. The key must be pre-determined by the users prior to making a manually encrypted call on a talk group and is entered into the radio using the keypad. For 128 bit encryption, this key is between 1 and 16 digits. For 256 bit encryption, this key is between 17 and 32 digits.
PAGE 185
MM-012125-001, Rev. M After changing systems, groups, scan state, etc., simply press the preset button to restore the settings. Presets are saved and restored to/from non-volatile memory. Changing the User ID (login in as a different user) clears the presets since they are stored on a per-user basis. Changing control heads does not recall presets for the previous control head.
PAGE 186
MM-012125-001, Rev. M 5.35.1 Send RTT Message via the Keypad (System Model Radios Only) 1. Press *5 <0…9> # on the keypad. The key associated with the RTT message (0-9) is configured via programming. 2. This message is displayed on the first line of the display when the key is pressed until another key is pressed. x If no message has been configured, “No Message” is displayed. x If a message is not assigned to the key, “No Entry” is displayed for the keypad sequence. 3.
PAGE 187
MM-012125-001, Rev. M 5.37 SCENE-OF-INCIDENT MODE The Scene-of-Incident mode (SOI) is user-selectable. The SOI mode provides local repeater function (VTAC) with no network connection. CAUTION When operating in the SOI mode, the radio is disconnected from the OpenSky network. Therefore, communications with radios and dispatch personnel on the network is not possible. Enter SOI Mode Manually Entering the Channel: 1. Scroll through the menu until the Client Mode menu appears. 2.
PAGE 188
MM-012125-001, Rev. M 6. EDACS/CONVENTIONAL/P25 OPERATION 6.1 TURN THE RADIO ON Rotate the POWER ON/OFF/VOLUME knob clockwise, out of detent to turn the radio on. A short beep (if enabled through programming) indicates the radio is ready for operation. The display indicates, if programmed, the last selected system name on line one and the last selected group or channel name on line two. NOTE NOTE 6.2 The radio can be programmed to require the entry of a PIN in order to operate the radio.
PAGE 189
MM-012125-001, Rev. M Figure 6-2: Scan Model Button function may vary depending upon radio programming. NOTE Table 6-1: Front Panel Default Controls and Functions PART Power OnOff/Volume Control knob FUNCTION Turn knob clockwise to power on the radio and increase volume. Turn counter-clockwise to decrease volume and power off the radio. NOTE Mic Connection The radio can be programmed to require the entry of a PIN in order to operate the radio.
PAGE 190
MM-012125-001, Rev. M 6.3 PART FUNCTION STS Permits the transmission of a pre-programmed status message to an EDACS or P25 Trunked site. MSG Permits the transmission of a pre-programmed message to an EDACS or P25 Trunked site. PHN Used to place telephone calls through the radio by selecting the interconnect special call function. DIS Used to show the key ID and whether or not it is valid or available. IND Used to call an individual or make an all-call by selecting the individual call function.
PAGE 191
MM-012125-001, Rev. M ICON DESCRIPTION Indicates selected group or channel is in scan list. Indicates selected group or channel is programmed as Priority 1 in scan list. Indicates selected group or channel is programmed as Priority 2 in scan list. Indicates Scan Mode enabled. Volume bars – indicate relative volume level. Indicates the current channel is set up as an analog channel. Indicates the current channel is set up as a ProVoice channel.
PAGE 192
MM-012125-001, Rev. M MESSAGE NAME DESCRIPTION DATA T/R Transmit/Receive Data Indicates the radio is transmitting/receiving a data call. DATA OFF Data OFF Indicates the radio is in the data disabled state. Displayed on line 1. DATA ON Data ON Indicates the radio has been toggled to the data enable state. Displayed for two seconds on line 1 when toggled to enable state. SYSC ON System Scan Features ON Indicates the System Scan features are enabled.
PAGE 193
MM-012125-001, Rev. M MESSAGE NAME SYS ALL System All Call Displayed on line 1 to indicate a system all-call has been received. Ggg-v.vv Code Group and Revision Number This is code group and revision number that is displayed in line 2 when the menu item “REVISION” is selected. The ‘gg’ is the group number of the software. The first ‘v’ is the hardware version and ‘vv’ is the revision of the software. *PHONE* Phone Call Displayed when an initiated phone call is in progress.
PAGE 194
MM-012125-001, Rev. M NAME Call Originate TONE One short midpitched tone Autokey One mid-pitched tone Call Queued One high-pitched tone System Busy Three low-pitched tones. Call Denied Carrier Control Timer Key Press Alert Page (P25T Only) Out of Range 6.8 One low-pitched tone Five short highpitched warning tones followed by a long lowpitched tone One short tone Three highpitched tones One low pitched tone DESCRIPTION Sounds after keying the radio (Push-To-Talk button is pressed).
PAGE 195
MM-012125-001, Rev. M An example of the menu item selection process and menu item parameter change is detailed below for the brightness menu item. 1. Press MENU to enter the menu mode. 2. Press the ramp control until the display shows: MENU BACKLGHT 3. Press MENU. 4. Use the ramp control to increase or decrease backlight brightness. Once the desired setting is reached, press MENU to store the value and return to the normal display. 5. For menu items that display radio information, use displays.
PAGE 196
MM-012125-001, Rev. M FEATURE DISPLAY EDACS Menu item: ECP1 SCN Conventional Priority 1 Scan Group selection Menu item: GRP Status Condition Menu item: STATUS Message Condition Feature Encryption Display System Scan Enable Talkaround feature Type 99 Decode Enable Display GPS information Select Mixed System/Zone Display Caller ID View/Modify Custom Scan List 6.
PAGE 197
MM-012125-001, Rev. M To enable a feature in a radio, call Harris and they will ask for the ROM serial number. The serial number shown here is for example only. 6.9.2 Feature Encryption Data Stream Example: These data streams define the features the user has enabled in his radio and are required by Harris to enable other features. The data streams shown here are for example only. There are three displays: FD1, FD2, and FD3. All three are required.
PAGE 198
MM-012125-001, Rev. M Table 6-6 lists possible features available in the user's radio.
PAGE 199
MM-012125-001, Rev. M 6.10 VOICE ANNUNCIATION When enabled via programming, the Voice Annunciation feature provides audible feedback for various radio operations. The radio can be programmed to play an audio message for any or all of the following. This message can be a pre-recorded (canned) message or a user-recorded message.
PAGE 200
MM-012125-001, Rev. M METHOD 1: If group selection is programmed to the SYSTEM/GROUP/CHANNEL knob, select a group by turning the SYSTEM/GROUP/CHANNEL knob to the desired group. The display registers the new group name on line 2. If the wrap option is OFF and the knob is moved to a position greater than the number of programmed groups, the highest programmed group remains selected.
PAGE 201
MM-012125-001, Rev. M 6.13 ENCRYPTION The M5300 mobile radio supports AES and DES encryption. When operating on a group or channel programmed for encryption, all transmissions are private and the radio receives clear and private signals. is displayed when encryption is enabled. If the selected group or channel is programmed for autoselect capability, the mode may be toggled between encrypted and unencrypted by pressing the MENU key, and then selecting the PRIVATE menu option.
PAGE 202
MM-012125-001, Rev. M 6.13.4 Transmit an Encrypted Call 1. Select the desired group or channel. 2. Enable encryption by pressing the MENU button and then selecting the PRIVATE menu option, or press the button on the control head that has been programmed for PRIVATE. x If the last state of the radio was encryption enabled, then encryption is enabled on power up.
PAGE 203
MM-012125-001, Rev. M 2. Ensure that conventional channels are not busy by pressing the CLR button to briefly disable any channel decoding and unmute the receiver, or observe the unlit BSY indicator. If the Channel Busy Lockout feature is programmed for the selected channel, the radio does not transmit when the channel is busy. 3. Press and hold the PTT button. 4. When the working channel is assigned, the TX and BSY indicators are turned ON and a short beep is sounded indicating communication can begin.
PAGE 204
MM-012125-001, Rev. M 2. When the working channel assignment is received, the radio sounds a single beep (Autokey alert tone) indicating it is ready for voice transmission. *TXEMER* flashes on line 2 in the display until the emergency is cleared. 3. Press PTT and speak into the microphone in a normal voice. 4. Release PTT when the transmission is complete and listen for a reply. 5.
PAGE 205
MM-012125-001, Rev. M 6.19 MIXED SYSTEM ZONES A Zone is a grouping of analog conventional channels, P25 conventional channels, and/or P25T or P25C talkgroups. Mixed System Zones are defined in RPM and can be comprised of any combination of channels/groups from multiple systems as long as the system definitions share the same WACN/System ID. If a Mixed System Zone is not configured in RPM, it will not appear on the radio. Up to 50 Mixed System Zones can be defined. To select a Mixed System Zone: 1.
PAGE 206
MM-012125-001, Rev. M Stealth Mode can be configured to persist through a power cycle. 6.22 SYSTEM SCAN OPERATION (EDACS AND P25 TRUNKED) The radio can be programmed with the following System Scan features. These features are automatically enabled upon radio power up. A key or menu option is also defined to allow the System Scan features to be toggled during radio operation. The System Scan state is maintained through system changes but defaults to ON at power up. 6.22.
PAGE 207
MM-012125-001, Rev. M 6.22.6 Menu Selection Press MENU and then use the ramp control to scroll through the selections until SYS SCAN is displayed. Then press MENU to toggle the System Scan state. The SYSC ON or SYSC OFF display message is displayed for two seconds to show the new state. 6.22.7 Pre-Programmed Keypad Key Press the pre-programmed key and the SYSC ON or SYSC OFF display message is displayed for two seconds to show the new state. 6.
PAGE 208
MM-012125-001, Rev. M The priority level selection sequence only advances the group to the next higher priority level and stops at priority level 1. To select a lower priority level, the group/channel must be deleted from the scan list and then added back to the scan list. Each new group/channel added to the scan list starts at the lowest priority.
PAGE 209
MM-012125-001, Rev. M 6.23.6 Turn Scan Off Turn scan operation off by pressing SCAN. The radio resumes operation on the selected group/channel. 6.23.7 Mixed Zone Scan The Mixed Zone Scan (MZS) feature gives the user the capability to scan based on a custom scan list that is assigned at the system level. The Custom Scan (CS) list can contain System and Channel/Group configurations across P25 Trunk, P25 Conventional, and Analog Systems.
PAGE 210
MM-012125-001, Rev. M 6.23.7.3 Edit Custom Scan Lists Scan must be off to edit a Custom Scan List. NOTE 1. From the radio menu, select CUSTSCAN. 2. 3. 4. Select EDIT LST. Select the desired system from the list. Select the desired channel group. Scroll through available options: x Add the channel/group to the scan list. x Change the channel’s/group’s scan priority. x Delete the channel/group from the scan list. x Nuisance delete the channel/group. 5.
PAGE 211
MM-012125-001, Rev. M To access the list, press the IND key twice. Use display the time elapsed since the call was received. to scroll through the list. Press the MENU key to 6.24.2 Call Storage Lists There are two lists available for call storage in the radio, the calls received list (1-10) and the personality list (1-99 as defined by the user). When the individual call mode is entered by pressing IND, the calls received list is available.
PAGE 212
MM-012125-001, Rev. M 2. Press the PTT button. The radio performs the necessary signaling to obtain a communication channel. When the signaling is complete and the radio is clear to transmit, the TX indicator turns ON and the channel access tone sounds. Line 1 shows the called individual's name if found in the list of stored individuals or ID followed by the logical ID number of the unit being called. The message *INDV* displays on line 2. Proceed with the message. 6.
PAGE 213
MM-012125-001, Rev. M 6.26.3 DTMF Overdial/Conventional Mode Telephone Interconnect Once the radio has established a connection to the public telephone system, it may be necessary to "overdial" more digits to access banking services, answering machines, credit card calls or other types of systems that require DTMF (Dual-Tone Multi-Frequency) access digits. Overdial operation can also be used to initiate a telephone interconnect call via DTMF signaling if a dial tone has already been accessed on the system.
PAGE 214
MM-012125-001, Rev. M 6.27 MOBILE DATA The M5300 Series mobile radios permit either voice or data calls to be transmitted or received. The radio can handle only one type of call at a time; however, selection of either data or voice is transparent to the operator. The mobile radios can be connected to Mobile Data Terminals (MDT) or to a host computer. Any RS-232 compatible device that supports the Radio Data Interface (RDI) protocol (Version 1.91 or greater) can be connected to the mobile radio.
PAGE 215
MM-012125-001, Rev. M 6.27.4 Exiting Data Calls Under normal conditions, the radio enters the scan lockout mode and returns to the control channel after completion of a data call (transmit or receive). If, during a data call, one of the following conditions occurs, the data call is immediately terminated and the radio performs the desired function: x The PTT is activated. x The PTT is in Public Address Mode. x An emergency is declared by pressing the pre-programmed emergency button.
PAGE 216
MM-012125-001, Rev. M 6.28 STATUS/MESSAGE OPERATION (EDACS AND P25 TRUNKED) Status and message operation is possible with either the Scan or System version of the M5300 Series mobile radio unit. The following procedure is applicable for the System version. For operation with the Scan version, the four primary keycaps must be reconfigured and pre-programmed for status/message operation. 6.28.
PAGE 217
MM-012125-001, Rev. M 6.29 EDACS CONVENTIONAL P1 SCAN This feature permits the radio user to scan a pre-programmed conventional system and channel as a Priority 1 (P1) channel while the radio is selected for EDACS trunked system. If activity is detected on the conventional P1 channel, the radio unmutes and remains on this conventional channel for the programmable hang time. The radio must be pre-programmed to designate a button for scan ON/OFF operation. 6.
PAGE 218
MM-012125-001, Rev. M NOTE When the squelch adjust feature is activated, Channel Guard, T99 decode, and Scan are disabled. When the squelch adjust feature is exited, Channel Guard, T99 decode, and Scan are restored to their previous states. 6.32.1 Menu Selection 1. Press the MENU key and then use the ramp control SQUELCH is displayed. Then press MENU again. to scroll through the selections until 2. The display shows SQLCH=xx, where "xx" is the value between 1 and 16. 3.
PAGE 219
MM-012125-001, Rev. M Type 99 is automatically disabled when Scan is enabled. NOTE 6.33.1 Menu Selection Press MENU and then use the ramp control to scroll through the selections until T99 ENAB is displayed. Then press MENU to toggle the Type 99 decode state. The T99 ON or T99 OFF display message is displayed for two seconds to show the new state. 6.33.2 Pre-Programmed Keypad Key Press the pre-programmed key and the T99 ON or T99 OFF display message is displayed for two seconds to show the new state. 6.
PAGE 220
MM-012125-001, Rev. M the PLAYBACK key is pressed, the last recording is replayed and any future recordings are stopped. Pressing PLAYBACK again repeats the same recorded call. Pressing and holding the PLAYBACK key until the tone sounds erases the recording and starts the recording of incoming calls again. If a call is received while the recorded call is playing, the recorded call continues to play, rather than the received audio.
PAGE 221
MM-012125-001, Rev. M 6.37.4 To view the current time: Select TIME with the MENU key to retrieve the current date and time. 6.38 VIEW GPS INFORMATION If the M5300 is equipped with the optional GPS receiver module, you can view your position and satellite information via the GPS Menu. GPS requires an unobstructed view of the sky and the signal is greatly diminished inside buildings, tunnels, heavily forested areas, etc.
PAGE 222
MM-012125-001, Rev. M 7. BASIC TROUBLESHOOTING If the radio is not operating properly, check Table 7-1 for likely causes. For additional assistance, contact a qualified service technician. Table 7-1: Basic Troubleshooting SYMPTOM CAUSE SOLUTION Radio will not turn on. No power. Test the connection to the vehicle power supply. Radio will not turn off. If in multiple control head configuration, one of the attached control heads is still powered up. Power off all control heads.
PAGE 223
MM-012125-001, Rev. M 8. CUSTOMER SERVICE 8.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
PAGE 224
MM-012125-001, Rev. M APPENDIX A CONFIGURING ENCRYPTION Refer to the following documentation for advanced programming and setup instructions: A.
PAGE 225
MM-012125-001, Rev. M c. Scroll through and select the HKL option and press the MENU button. The radio can now accept keys from the Harris Keyloader. 5. Load the UKEK file from the Crypto Officer onto the PC. 6. Run the RPM application and setup the radio’s Mission Plan according the SLN Binding Report information. 7. Setup the talk groups and the SLN mappings (Talk Group ID to SLN). This includes mapping SLNs to the “System” keys (PSTN, All Call, etc.). 8.
PAGE 226
MM-012125-001, Rev. M a. Press the radio’s MENU button. b. Scroll through the menu to select the KEYLOAD option and press the MENU button to activate. c. Scroll through and select the HKL option and press the MENU button. The radio can now accept keys from the Harris Keyloader. 12. Select Radio from the drop-down and click Load. 13. Click Finish. A.2.3 Power on the Motorola KVL Device 1. Connect KVL Device to the radio using cable 14002-0143-01.
PAGE 227
MM-012125-001, Rev. M Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the following: Harris Corporation PSPC Business Technical Publications 221 Jefferson Ridge Parkway Lynchburg, VA 24501 106 fax your comments to: 1-434-455-6851 or e-mail us at: PSPC_TechPubs@harris.
PAGE 228
Public Safety and Professional Communications | www.pspc.harris.
PAGE 229
Product Safety Manual MM-014763-001 Rev. N, Mar/15 This his m manuall contains iimportant mportant safety information infor regarding specific absorption rate (S SAR) and nd RF exposure limits included in United States and international standards. (SAR) Rea d the information in this this manual manua before operating your radio.
PAGE 230
MM-014763-001, Rev. N MANUAL REVISION HISTORY REV. DATE REASON FOR CHANGE L Apr/13 Revised regulatory information and related publications. Removed installation information (see publication MM-014763-400). M Oct/13 Added support for XG-75M. N Mar/15 Revised to include model RU-144750-061 (Rev. L) and French translations.
PAGE 231
MM-014763-001, Rev. N TABLE OF CONTENTS Section 1 Page REGULATORY AND SAFETY INFORMATION .................................................................... 5 1.1 1.2 SAFETY SYMBOL CONVENTIONS ................................................................................................. 5 REGULATORY APPROVALS ........................................................................................................... 6 1.2.1 Applicable Type Acceptance/Certification Numbers .............................
PAGE 232
MM-014763-001, Rev. N TABLE OF CONTENTS Section 6 Page WARRANTY REGISTRATION ................................................................................................ 37 LIST OF TABLES Page Table 2-1: FCC Type Acceptance ......................................................................................................................... 6 Table 2-2: Industry Canada Type Acceptance .......................................................................................................
PAGE 233
MM-014763-001, Rev. N 1 REGULATORY AND SAFETY INFORMATION 1.1 SAFETY SYMBOL CONVENTIONS The following conventions are used in this manual to alert the user to general safety precautions that must be observed during all phases of operation, installation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere violates safety standards of design, manufacture, and intended use of the product.
PAGE 234
MM-014763-001, Rev. N 1.2 REGULATORY APPROVALS 1.2.1 Applicable Type Acceptance/Certification Numbers Table 1-1: FCC Type Acceptance FREQUENCY RANGE/WATTAGE FCC TYPE ACCEPTANCE NUMBER RU-144750-041 136-174 MHz, 50 Watt OWDTR-055-E RU-144750-051 136-174 MHz, 110 Watt OWDTR-056-E RU-144750-021 378-430 MHz, 50 Watt OWDTR-061-E RU-144750-031 440-512 MHz, 50 Watt OWDTR-062-E 14018-0010-01 330-380 MHz, 40 Watt N/A RU-144750-061 Rev.
PAGE 235
MM-014763-001, Rev. N 1.3 RADIO FREQUENCY INTERFERENCE 1.3.1 FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and, 2. This device must accept any interference received, including interference that may cause undesired operation. 1.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s).
PAGE 236
MM-014763-001, Rev. N of protection. All two-way radios marketed in North America are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it.
PAGE 237
MM-014763-001, Rev. N Based on the highest radiated RF power and the highest antenna gain in antennas used with M5300, M7300, and XG-75M series radios, the distances listed in Table 1-3 and Table 1-4 are considered as safe distances for controlled and uncontrolled environments with the M5300, M7300, and XG-75M series mobile radios transmitting at a maximum 50% duty cycle: 1.5.
PAGE 238
MM-014763-001, Rev. N 1.5.3 Mobile Antennas (Vehicle Installations) Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER VHF (50 W) AN-225002-001 136 to 174 MHz, 0 dBd Gain VHF (50 W) AN-225006-001 132 to 960 MHz, 0 dBd Gain* VHF (50 W) AN-225002-003 ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 24.
PAGE 239
MM-014763-001, Rev. N Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 20 Inches (51 Centimeters) 45 Inches (114 Centimeters) 9.8 Inches (25 Centimeters) 21.
PAGE 240
MM-014763-001, Rev.
PAGE 241
MM-014763-001, Rev.
PAGE 242
MM-014763-001, Rev. N Table 1-3: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations) MOBILE RADIO FREQUENCY SPLIT * 14 ANTENNA PART NUMBER ANTENNA DESCRIPTION RECOMMENDED MINIMUM LATERAL HUMAN BODY DISTANCE FROM TRANSMITTING ANTENNA CONTROLLED ENVIRONMENT UNCONTROLLED ENVIRONMENT 9.8 Inches (25 Centimeters) 21.7 Inches (55 Centimeters) 20 inches (51 centimeters) 44.
PAGE 243
MM-014763-001, Rev. N 1.5.4 Mobile Antennas (Motorcycle Installations) Table 1-4: Rated Power and Recommended Minimum Safe Lateral Distance (Motorcycle Installation) RF BAND MAX. TX POWER (WATTS) ANTENNA PART NUMBER 20 LE-OM150K.125/TNC 136 to 174 MHz MotorcycleMount; 2.
PAGE 244
MM-014763-001, Rev. N 1.6 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION To ensure bodily exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use. Always adhere to the following basic guidelines: x The push-to-talk button should only be depressed when intending to send a voice message. x The radio should only be used for necessary work-related communications. x The radio should only be used by authorized and trained personnel.
PAGE 245
MM-014763-001, Rev. N x Vehicles Powered By Liquefied Petroleum (LP) Gas — Radio installation in vehicles powered by liquefied petroleum gas, where the LP gas container is located in the trunk or other sealed-off space within the interior of the vehicle, must conform to the National Fire Protection Association standard NFPA 58. This requires: ¾ The space containing the radio equipment must be isolated by a seal from the space containing the LP gas container and its fittings.
PAGE 246
MM-014763-001, Rev. N x It is a violation of FCC rules to interrupt any distress or emergency message. The radio operates in much the same way as a telephone “party line.” Therefore, always listen to make sure the channel is clear before transmitting. Emergency calls have priority over all other messages. If someone is sending an emergency message – such as reporting a fire or asking for help in an accident, do not transmit unless assistance can be offered.
PAGE 247
MM-014763-001, Rev. N 2 RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit.
PAGE 248
MM-014763-001, Rev. N 2.2 CONFORMITÉ À LA RÉGLEMENTATION 2.2.
PAGE 249
MM-014763-001, Rev. N 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES 2.3.1 Partie 15 de la FCC Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas causer une interférence nuisible; et 2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un fonctionnement non souhaité. 2.3.
PAGE 250
MM-014763-001, Rev. N bidirectionnelles commercialisées en Amérique du Nord sont conçues, fabriquées et testées pour s’assurer qu’elles satisfont les niveaux d’exposition aux RF établis par le gouvernement. Les fabricants recommandent également des consignes d’utilisation particulières aux utilisateurs de radios bidirectionnelles.
PAGE 251
MM-014763-001, Rev. N Tableau 2-3 par Tableau 2-4 indiquent les distances latérales sécuritaires minimales recommandées pour un environnement contrôlé et pour les spectateurs ignorants dans un environnement non contrôlé, d’antennes de transmission (c.-à-d., des monopôles sur un plan de sol, ou des dipôles) à une puissance de radio évaluée pour les radios mobiles installées dans un véhicule.
PAGE 252
MM-014763-001, Rev. N 2.5.
PAGE 253
MM-014763-001, Rev.
PAGE 254
MM-014763-001, Rev.
PAGE 255
MM-014763-001, Rev.
PAGE 256
MM-014763-001, Rev.
PAGE 257
MM-014763-001, Rev.
PAGE 258
MM-014763-001, Rev.
PAGE 259
MM-014763-001, Rev. N 2.5.4 Monté Antennes (Motocyclette) Tableau 2-4: Distance latérale sécuritaire minimale recommandée d’une antenne de transmission branchée sur une radio Motocyclette NUMÉRO DE PIÈCE DE L’ÉLÉMENT DE L’ANTENNE DESCRIPTION DE L’ANTENNE VHF LE-OM150K.125/TNC 136 to 174 MHz motocyclette-monture; gain de 2.
PAGE 260
MM-014763-001, Rev. N 2.6 RENSEIGNEMENTS SUR LA FORMATION SUR LA SANTÉ ET LA SÉCURITÉ AU TRAVAIL S’assurer que l’exposition physique à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle. Toujours se conformer aux directives de base suivantes: x Le bouton de microphone doit être abaissé seulement lorsque l’on souhaite envoyer un message vocal. x La radio doit être utilisée seulement pour les communications nécessaires liées au travail.
PAGE 261
MM-014763-001, Rev. N x Énergie des fréquences radio – Pour prévenir toute brûlure ou toute blessure physique connexe causée par l'énergie des fréquences radio, ne pas faire fonctionner l'émetteur lorsqu'une personne à l'extérieur du véhicule est située en deçà de la distance minimale sécuritaire de l'antenne, comme stipulé à la Section 2.5.
PAGE 262
MM-014763-001, Rev. N Par conséquent, toujours écouter avant d'émettre afin de s'assurer que le canal est libre. Les appels d'urgence sont prioritaires sur tous les autres messages. Si un message d'urgence est en cours de transmission (pour signaler un incendie ou demander de l'aide à la suite d'un accident, par exemple), ne pas émettre de messages sauf pour venir en aide. x La loi fédérale interdit l'utilisation d'un langage obscène ou blasphématoire.
PAGE 263
MM-014763-001, Rev. N 3 OPTIONS AND ACCESSORIES A complete list of Options and Accessories approved for use with the M5300, M7300, and XG-75M mobile radios can be found online in the applicable Operator’s Manual at http://pspc.harris.com/Products/Radios.aspx. Also reference the Products and Services Catalog for all available options and accessories, including those items that do not adversely affect the RF energy exposure.
PAGE 264
MM-014763-001, Rev. N 5 CUSTOMER SERVICE 5.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
PAGE 265
MM-014763-001, Rev. N 6 WARRANTY REGISTRATION Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at the Customer Care center webpage: http://www.pspc.harris.com/Service/Customerservice.aspx. While on the webpage, please review the applicable battery and/or product warranty literature.
PAGE 266
Public Safety and Professional Communications | www.pspc.harris.