Operator’s Manual 14221-1500-2000 Rev.
14221-1500-2000, Rev. K REV DATE - Dec/11 Initial release. REASON FOR REVISION A Jan/12 Updated to finalize features and functions. B Jun/12 Updated to include P25T information and included cleaning instructions. C Jan/13 Added 700/800 MHz radios to Table 2-1. D Sep/13 Updated Options and Accessories and updated warranty. Added UHF-L radios. Updated cleaning instructions. Added French translations. E Mar/14 Added EDACS and Bluetooth operation.
14221-1500-2000, Rev. K This device is a RF transceiver intended for land mobile radio applications. The device may have use restrictions, which require that the national authority be contacted for any system licensing requirements, frequency use, allowable power level, etc.
14221-1500-2000, Rev.
14221-1500-2000, Rev. K Česky [Czech] Harris Corporation tímto prohlašuje, že tento XG 25P UHF-L(378-470 MHz), 7/800 (764870MHz) je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede Harris Corporation erklærer herved, at følgende udstyr XG 25P UHF-L (378-470 MHz), 7/800 (764-870MHz) overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
14221-1500-2000, Rev. K Polski [Polish] Niniejszym Harris Corporation oświadcza, że XG 25P UHF-L (378-470 MHz), 7/800 (764870MHz) jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] Harris Corporation declara que este XG 25P UHF-L (378-470 MHz), 7/800 (764-870MHz) está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
14221-1500-2000, Rev. K TABLE OF CONTENTS Page 1. REGULATORY AND SAFETY INFORMATION........................................................................... 13 1.1 SAFETY CONVENTIONS ........................................................................................................ 13 1.2 SAFETY TRAINING INFORMATION .................................................................................... 13 1.2.1 RF Exposure Guidelines .....................................................................
14221-1500-2000, Rev. K TABLE OF CONTENTS 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 7.21 7.22 7.23 7.24 7.25 7.26 7.27 8 Page DISPLAY ................................................................................................................................... 34 TRI-COLOR LED ...................................................................................................................... 35 RADIO STATUS MESSAGES ...................................
14221-1500-2000, Rev. K TABLE OF CONTENTS 7.28 7.29 7.30 7.31 7.32 7.33 7.34 7.35 8. Page 7.27.2 Sending a Telephone Interconnect Call ......................................................................... 53 7.27.3 Dual-Tone Multi-Frequency: Overdial .......................................................................... 54 PRE-STORING INDIVIDUAL AND TELEPHONE INTERCONNECT CALLS FROM THE KEYPAD .....................................................................................................
14221-1500-2000, Rev. K TABLE OF CONTENTS 8.10 8.11 8.12 8.13 8.14 8.15 8.16 8.17 8.18 8.19 8.20 8.21 8.22 8.23 8.24 8.25 8.26 8.27 8.28 8.29 10 Page 8.9.2 Add a Device ................................................................................................................. 71 8.9.3 Delete a Device .............................................................................................................. 72 8.9.4 Turn Off Bluetooth ......................................................
14221-1500-2000, Rev. K TABLE OF CONTENTS 8.30 8.31 8.32 8.33 8.34 9. Page 8.29.1 Automatic Encryption.................................................................................................... 88 8.29.2 Manual Encryption (System Model Only) .................................................................... 88 STATUS MESSAGES ............................................................................................................... 89 8.30.
14221-1500-2000, Rev. K TABLE OF CONTENTS Page Figure 8-4: System Model Front Panel .......................................................................................................... 62 Figure 8-5: Radio Display OpenSky Mode.................................................................................................... 63 Figure 8-6: Full Cycle Battery Charge Indicator ........................................................................................... 64 Figure 8-7: Tri-Color LED........
14221-1500-2000, Rev. K 1. REGULATORY AND SAFETY INFORMATION 1.1 SAFETY CONVENTIONS The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warning elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product.
221-1500-2000, Rev.
14221-1500-2000, Rev. K Table 1-1: RF Exposure Compliance Testing Distances TESTED DISTANCES (worst case scenario) RADIO FREQUENCY Body Face VHF (136-174 MHz) 1.5 cm 2.5 cm 700/800 MHz 1.6 cm 2.5 cm UHF-L (378-470 MHz) 1.6 cm 2.5 cm The information in this section provides the information needed to make the user aware of RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits and/or the exposure limit values in Annex A of EU Directive 2004/40/EC. 1.2.
14221-1500-2000, Rev. K 1.4.1 Efficient Radio Operation Keep the antenna in a vertical position when receiving or transmitting a message. Do NOT hold onto the antenna when the radio is powered on! WARNING 1.4.1.1 WARNING CAUTION 1.4.1.2 CAUTION 1.4.1.3 WARNING 1.4.1.4 WARNING 16 Antenna Care and Replacement Do not use the portable radio with a damaged or missing antenna. A minor burn may result if a damaged antenna comes into contact with the skin. Replace a damaged antenna immediately.
14221-1500-2000, Rev. K 1.4.1.5 Potentially Explosive Atmospheres Areas with potentially explosive atmospheres are often, but not always, clearly marked. These may be fuelling areas, such as gas stations, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. WARNING Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
14221-1500-2000, Rev. K 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ 2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit.
14221-1500-2000, Rev. K 2.2.1 Directives sur l’exposition aux RF AVERTISSEMENT Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les directives suivantes : • N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la radio et également causer un dépassement des limites d’exposition aux RF de la FCC.
14221-1500-2000, Rev. K 2.3 INTERFÉRENCE DES RADIOFRÉQUENCES 2.3.1 Partie 15 de la FCC Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas causer une interférence nuisible; et 2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un fonctionnement non souhaité. 2.3.
14221-1500-2000, Rev. K AVERTISSEMENT 2.4.1.2 AVERTISSEMENT 2.4.1.3 MISE EN GARDE 2.4.1.4 MISE EN GARDE 2.4.1.5 Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et enfreindre la réglementation de la FCC. (Reportez-vous à Table 6-1.) Appareils Électroniques L’énergie des RF provenant de radios portatives peut affecter certains appareils électroniques.
14221-1500-2000, Rev. K 3. CLEANING Keep the exterior of the radio, battery, antenna, and radio accessories clean. Periodically clean using the following procedures: 1. To remove dust and dirt, clean using damp clean cloth (warm water and mild detergent soap). 2. Follow by wiping with damp (warm water) clean cloth. Wipe dry with clean cloth. 3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or grease.
14221-1500-2000, Rev. K 4. BATTERIES The XG-25P series portable radios use rechargeable, recyclable Nickel Metal Hydride (NiMH), Lithium Polymer (Li-Poly), or Lithium Ion (Li-Ion) batteries. Please read the battery information provided carefully to maximize the useful life of each type of battery. 4.1 WARNING Do not disassemble or modify Lithium battery packs. Lithium battery packs are equipped with built-in safety and protection features.
14221-1500-2000, Rev. K packs experience some capacity loss during storage, the shelf life for Li-Ion battery packs is about 3 months. However, note that any capacity drop which occurs during storage is permanent and cannot be reversed. Li-Ion battery packs should be purchased and used immediately. They should not be stockpiled without a rotating stock plan. 4.3 CHARGING BATTERY PACKS Battery chargers are available from Harris with nominal charge times.
14221-1500-2000, Rev. K 4.5 CHANGING THE BATTERY PACK 4.5.1 Removing the Battery Pack Make sure the power to the radio is turned off. CAUTION Although the XG-25P has been designed to tolerate changing the battery pack without turning power off, Harris recommends turning the radio off before changing battery packs to ensure safety and best operation. 1. Refer to Figure 4-1. Press or pull both latches on either side of the battery pack toward the bottom of the radio simultaneously. 2.
14221-1500-2000, Rev. K Figure 4-2: Attaching the Battery Pack 4.6 BATTERY DISPOSAL In no instance should a battery be incinerated. Disposing of a battery by burning will cause an explosion. WARNING RECHARGEABLE BATTERY PACK DISPOSAL – The product you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream.
14221-1500-2000, Rev. K 5. INTRODUCTION 5.1 GENERAL The XG-25P is available in two models: the Scan model with a limited 6-button front-mounted keypad and the System model with a 15-button DTMF front-mounted keypad. The Harris XG-25P portable radio delivers end-to-end digital voice and IP data communications.
14221-1500-2000, Rev. K 5.2 UNIVERSAL DEVICE CONNECTOR The Universal Device Connector (UDC) provides connections for external accessories such as a headset, a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the radio. The UDC pins perform different functions depending on the accessory attached to the UDC.
14221-1500-2000, Rev. K 6. OPTIONS AND ACCESSORIES Table 6-1 lists the Options and Accessories tested for use with the XG-25P series portable radios. Refer to the maintenance manual corresponding to the frequency of your XG-25P or to Harris Products and Services Catalog for a complete list of options and accessories, including those items that do not adversely affect the RF energy exposure. WARNING Always use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc).
14221-1500-2000, Rev.
14221-1500-2000, Rev. K 7. EDACS, CONVENTIONAL, AND P25 OPERATION 7.1 TURNING ON THE RADIO 1. Power on the radio by rotating the power on-off/volume knob clockwise. A short alert signal (if enabled through programming) indicates the radio is ready to use. 2. The display shows the last selected system and group or a default system and group (depending on programming). 3. Adjust the power on-off/volume knob to the desired volume level. 4. Select the desired system and group.
14221-1500-2000, Rev. K 7.2.1 Buttons, Knobs, and Switch The functions of the buttons and knob controls vary depending on mode of operation. Primary functions of the button, switch, and knob controls are discussed in general terms in the following. Table 7-1: Buttons, Knobs, and Switch Functions POWER ON/OFF-VOLUME CONTROL KNOB VOICE GROUP SELECTION KNOB EMERGENCY/HOME BUTTON PUSH-TO-TALK (PTT) BUTTON Applies power to the radio and adjusts audio volume.
14221-1500-2000, Rev. K 7.2.2 Keypad The front mounted keypad of the Scan model has six buttons and System model has 15 buttons. Refer to Figure 7-3 and Figure 7-4, respectively. Figure 7-3: Scan Model Front Panel Figure 7-4: System Model Front Panel The primary and secondary functions of each key, where applicable, are described in Table 7-2 and the following section. Table 7-2: XG-25P Front Keypad Functions KEY FUNCTION Primary Function: Accesses the menu.
14221-1500-2000, Rev. K KEY FUNCTION Primary function: Deletes selected groups or channels of the currently selected system from the Scan list. Primary function: Inverts display – Toggle normal/invert. Requires ECP R16B or later. Secondary function: The secondary function of these keys acts as a typical DTMF telephone pad, and are used to place telephone interconnect and individual (unit-to-unit) calls. Primary function: In EDACS and P25 modes, initiates telephone interconnect calls.
14221-1500-2000, Rev. K ICON DESCRIPTIONS Steady – Indicates the current channel is set up as a ProVoice channel. Steady –The current channel is set up as an analog channel. Animated (rotates clockwise) – Scan mode enabled. If icon is not visible – Scan is disabled. Steady – Priority 1 group or channel. Steady – Priority 2 group or channel. Steady – Group or channel in scan list. Steady – Special call mode (individual or telephone). Steady – Battery charge indicator.
14221-1500-2000, Rev. K 7.6 Message Name Description SYSC ON System Scan Features On Indicates the System Scan features are enabled. SYSC OFF System Scan Features Off Indicates the System Scan features are disabled. LOW BATT Low Battery Battery voltage has dropped to the point to where the radio is no longer able to transmit. The radio will still receive calls until the battery is discharged beyond the point of operation, at which time the radio automatically shuts down.
14221-1500-2000, Rev. K 7.7 ALERT TONES The XG-25P radio provides audible Alert Tones or “beeps” to indicate the various operating conditions (see Table 7-4). Table 7-4: Alert Tones NAME TONE DESCRIPTION Call Originate one short mid-pitched OK to talk after pressing the push-to-talk button. Call Queued one high-pitched Call queued for processing. Autokey one mid-pitched Queued call received channel assignment. System Busy three low-pitched System busy or unable to complete call.
14221-1500-2000, Rev. K METHOD 3: NOTE (System model radios only) Direct Access: Press to enter the system/zone select mode. Press the numeric key, which is mapped to the desired system. Press . The radio will move to the selected system/zone. If system selection is programmed to the voice group selection knob, direct access to systems/zones is not available. Pressing or scrolls through different sets of 16 systems/zones each (banks) if more than 16 systems are programmed into the radio.
14221-1500-2000, Rev. K 5. Press twice to add as a Priority 2 group. 6. Press three times to add as a Priority 1 group. 7. Press to re-start scanning. 7.11.2 Scan Model Radio 1. Press to toggle scan off and verify is not displayed. 2. Select group or channel. 3. Press once to remove group or channel from the list. 4. Press once to add as a normal group or channel. 5. Press twice to add as a Priority 2 group. 6. Press three times to add as a Priority 1 group. 7. Press to re-start scanning.
14221-1500-2000, Rev. K 1. Press . The menu mode is entered. 2. Press or until the display shows: Figure 7-7: Backlight Menu Item Selection Parameter 3. Press . The backlight menu item is activated. Line one shows the active menu item and its current parameter setting. Line two shows the currently selected system or group name (see Figure 7-8). Figure 7-8: Backlight Menu Display 4. The menu item's parameter setting shown in the display can now be changed by using 5.
14221-1500-2000, Rev. K FEATURE DISPLAY PARAMETER SETTING COMMENT Display Current Encryption Key Display Current Home Group/Channel Select Desired System Add Group/Channel to Scan List Delete Group/Channel Add/Delete Scan List Select Telephone Numbers From Phone List Data Operation Select Individual Call from IC List Select Group Feature Encryption Display DISP KEY N/A HOME N/A Displays current encryption key. Informational display only. No selectable settings. Selects Home Group/Channel.
14221-1500-2000, Rev. K 7.13 BLUETOOTH The XG-25P delivers Bluetooth functionality for a wireless interface to selected accessories. The indicator flashes in the bottom of the display when Bluetooth is enabled but no accessory is currently connected. 7.13.1 Add a Device 1. Press to access the menu. 2. Press or to scroll through menu until BLUTOOTH is displayed and press 3. Press or to scroll through the menu until ADD DEVICE is displayed. 4. Press .
14221-1500-2000, Rev. K 3. *TXEMER* continues to flash until the emergency is cleared. See Section 7.22 for additional emergency operation. 4. Press the PTT and will reappear. 5. Release PTT when the transmission is complete. 7.17 LOCKING/UNLOCKING KEYPAD 1. Press button. 2. Within 1 second, press the button on the side of the radio. 7.18 HIGH/LOW POWER ADJUSTMENT Transmit power adjustment is possible if enabled through programming.
14221-1500-2000, Rev. K Figure 7-10: Group/Channel Encryption Key Display 7.19.2 Key Zero All cryptographic keys can be zeroed (erased from radio memory) by pressing the button and while still pressing this button, press and hold the button. Press both buttons for 2 seconds. A series of beeps will begin at the start of the 2 second period and then switch to a solid tone after the keys have been zeroed. The display will indicate KEY ZERO.
14221-1500-2000, Rev. K 7.20 SCAN OPERATION Groups/Channels that have been previously added to the scan list on a per system basis may be scanned. Each system's scan list is retained in memory when the radio is powered off or when the battery pack is removed. 7.20.1 Turning Scan On and Off 1. Toggle Scan operation on by pressing clockwise to indicate radio is scanning. (Scan model) or 2. Toggle Scan operation off by again pressing disappear. (System model).
14221-1500-2000, Rev. K System Model Radio 1. With scan operation turned off, select the desired group to add to the selected trunked system group scan list. 2. Press . The current priority status of the group will be displayed in column ten of line three for a time-out period. If the group is not part of the scan list, the status will be blank. 3. While the status is displayed, press line three. 4. Press to add the group to the scan list. The a second time to set the group to Priority 2.
14221-1500-2000, Rev. K 7.20.4 Nuisance Delete A group can also be deleted from the scan list, if it is not the currently selected group, by pressing the key (Scan model) or the key (System model) during scan operation while the radio is displaying the unwanted group. The group will be deleted from the system's group scan list in the same manner as if done using the steps above. Deletions done in this manner will not remain deleted if the radio is powered off and then powered on. 7.20.
14221-1500-2000, Rev. K 7.20.5.3 Edit Custom Scan Lists Scan must be off to edit a Custom Scan List. NOTE 1. From the radio menu, select CUSTSCAN. 2. Select EDIT LST. 3. Select the desired system from the list. 4. Select the desired channel group. Scroll through available options: • Add the channel/group to the scan list. • Change the channel’s/group’s scan priority. • Delete the channel/group from the scan list. • Nuisance delete the channel/group. 5.
14221-1500-2000, Rev. K enabled, as explained in the following sections. This priority scan timer is reset each time the PTT button is pressed or when the call is received. If the priority system control channel is found, or meets the predefined criteria (ProScan), the radio will automatically switch to the priority system. 7.21.2.
14221-1500-2000, Rev. K 7.23 MIXED SYSTEM ZONES A Zone is a grouping of analog conventional channels, P25 conventional channels, and/or talkgroups. Mixed System Zones are defined in RPM and can be comprised of any combination of channels/groups from multiple systems. If a Mixed System Zone is not configured in RPM, it will not appear on the radio. Up to 50 Mixed System Zones can be defined. To select a Mixed System Zone: 1. Press . 2. Press or to select ZONE and press . 3.
14221-1500-2000, Rev. K 7.26 INDIVIDUAL CALLS 7.26.1 Receiving and Responding to an Individual Call When the radio receives an individual call (a call directed only to the user's radio), it un-mutes on the assigned working channel and displays . The first line on the display shows the logical ID number of the unit sending the message, or the associated name if the ID number is found in the individual call list. The radio can be programmed to ring when an individual call is received.
14221-1500-2000, Rev. K Pressing the PTT will initiate an individual call to the displayed logical ID. Powering the radio off and on will clear this list. 7.26.2 Sending an Individual Call 7.26.2.1 Pre-Stored Individual Calls The following procedures describe how to initiate and complete a Pre-Stored Individual Call. System Model Radio 1. To select a pre-stored individual phone number, enter the individual call mode using the keys. is displayed.
14221-1500-2000, Rev. K Figure 7-13: Calls Received and Personality Lists The saved call list shows all ten storage locations. If no calls have been received, the saved call list will be empty and the pre-stored list will be available upon entering the individual call mode. When in the saved call list, pressing the key toggles the time stamp on and off. The time stamp indicates how long ago the call was received.
14221-1500-2000, Rev. K NOTE In half-duplex mode, only one person may talk at a time. The radio PTT button needs to be pressed in order to communicate to the individual called and released for the individual called to be heard. 7.27.2.2 Direct Dialing of Phone Calls (System Model Only) 1. If the phone number is not stored in the pre-stored list of phone numbers, but the phone number is known, it can be entered directly from the keypad.
14221-1500-2000, Rev. K System Model Radio 1. Follow the procedure in Section 7.27.2 to establish a connection to the telephone system or consult the system administrator for the procedure to access a dial tone on the trunked or conventional system. 2. Overdial numbers are transmitted using one of the following methods: METHOD 1: 1. Enter the overdial selection mode by pressing the button. 2. Use the or buttons to scroll through the list of stored numbers. is displayed.
14221-1500-2000, Rev. K 7.29 STATUS/MESSAGE OPERATION The Status and Message operations allow for the transmission of a pre-programmed status or a preprogrammed message to an EDACS or P25 site. Each Status and Message is assigned an ID then crossreferenced with the representative status condition (“Off Duty,” for example) or a message (“Call home”). In addition, Status conditions can also be associated with a programmable Menu entry (required for second method of transmitting a Status condition). 7.29.
14221-1500-2000, Rev. K 7.30 DYNAMIC REGROUP OPERATION (EDACS) The EDACS Dynamic Regroup Operation permits multiple Talk Groups (up to eight) to be added to a radio via the system manager. The radio must be pre-programmed to respond to regrouping. Dynamic regrouping will not be activated in a radio until the system manager sends an activation message. Each radio that receives and acknowledges the regrouping instructions is successfully regrouped. Pressing and holding the button for 2.
14221-1500-2000, Rev. K 7.32.2 Data Off Operation The radio can be placed in the data disabled state by any of the following methods. When the data state is disabled, DATA OFF appears on the top line of the display. • Declaring an emergency (not to be used unless an actual emergency condition exists). Alert tone will sound. • Pressing button • Pressing the pre-programmed “no data” (ND) key. Refer to previous bullet. (if pre-programmed as “no data” key). Alert tone will sound. 7.32.
14221-1500-2000, Rev. K 7.32.6 Data Lockout Mode During the voice call scan hang time (pre-programmed), the radio does not receive data calls. 7.33 SELECTIVE SIGNALING (CONVENTIONAL) Selective signaling controls the muting and unmuting of the receive audio. This allows a user or dispatcher to selectively call an individual radio or group of radios. The XG-25P portable radios support selective signaling in Type 99 decode format. 7.33.
14221-1500-2000, Rev. K 7.33.4 Type 99 Disable after PTT The radio may be programmed with the Type 99 Disable after PTT feature, which automatically disables the Type 99 decoder after a transmission. Use one of the methods outlined in the Section 7.33.3 to reset Type 99 operation. 7.34 RADIO TEXTLINK OPERATION Radio TextLink provides a simple means of exchanging pre-defined, or “canned,” text messages. This section describes how to send messages if the Radio TextLink feature is enabled. 7.34.
14221-1500-2000, Rev. K 8. OPENSKY OPERATION OpenSky is only available in 700/800 MHz models of the XG-25P series portable radios. NOTE Once an OpenSky system has been selected from the available systems on your XG-25P series portable radio, the characteristics described in the following sections govern operation. 8.1 CONTROLS The XG-25P portable radio features two rotary control knobs and an emergency button on the top of the radio. Refer to Figure 8-1.
14221-1500-2000, Rev. K VOICE GROUP SELECTION KNOB Used to select voice groups when operating within an OpenSky system. This is a 16-position rotary knob. EMERGENCY BUTTON Press the emergency button to declare an emergency. To clear an emergency, press and hold the Option 2 button . While holding , press the emergency button. Release both buttons when the “emergency cleared” tone sounds. PTT BUTTON The Push-To-Talk button must be pressed before voice transmission begins.
14221-1500-2000, Rev. K Table 8-2: Keypad Functions KEY FUNCTION Primary function: Acts much as an “enter” button to activate a selection. Secondary function: While in the “dwell display,” press repeatedly to scroll through and nd view status display (on 2 line) for current profile, caller, received talk group, and channel. Scrolls through available menu items (see Table 8-5). (Scan Model Only) (Scan Model Only) (Scan Model Only) Currently undefined in OpenSky mode. Toggles scan mode On/Off.
14221-1500-2000, Rev. K 8.1.4 Radio Status Icons Status Icons indicate the various operating characteristics of the radio. The icons show operating modes and conditions and appear on the third line of the display (see Table 8-3). Table 8-3: OpenSky Icons Descriptions STATUS ICON DESCRIPTIONS Steady – Received Signal Strength Indicator (RSSI). Steady – Radio is data registered. Steady – Stealth mode is enabled, all tones and the display backlight are disabled, voice is still heard.
14221-1500-2000, Rev. K 8.2 TRI-COLOR LED Figure 8-7: Tri-Color LED The Tri-Color LED changes color to indicate radio status and is visible from both the front and top of the radio (see Figure 8-7). In OpenSky mode the following radio states are reflected by the LED and the status they represent are: 8.3 Green: Receiving Red: Transmitting Orange: If the LED is flashing rapidly, the radio is receiving an emergency call.
14221-1500-2000, Rev. K If necessary, contact radio system administration personnel for login assistance and/or radio-specific login instructions. NOTE 8.4 LOG OFF THE NETWORK The *0## command de-registers the radio. Typically, this is automatically performed when powering down the radio. Using this method, the User ID is remembered by the radio, so only the password is needed at next login. If a user is logged in, it is necessary to log-off. 8.
14221-1500-2000, Rev. K OpenSky network administrator. An OpenSky talk group is similar to a channel within a conventional FM radio system. 8.6 OPENSKY DISPLAY OVERVIEW The 12-character x 3-line display shows the radio status. The first two lines of the display are text lines that change in response to user interaction with the menu buttons. Status icons appear in the bottom line (line 3) of the display (see Table 8-3). 8.6.
14221-1500-2000, Rev. K NAME TONE DESCRIPTION Emergency Cleared Tone Single long low-pitched tone Sounds when an emergency is cleared. Selective Call Ring Tone A ringing tone similar to a telephone Ringing is repeated every four (4) seconds until the call is accepted or rejected by the radio being called or until the network drops the call if unanswered after one minute.
14221-1500-2000, Rev. K 8.8 BASIC MENU STRUCTURE Table 8-5 illustrates the basic OpenSky menu structure. Menu items will vary depending upon system programming, radio hardware, and optional configurations. All menus except the dwell display menu can be turned off by network administration personnel.
14221-1500-2000, Rev. K MENU NAME RADIO DISPLAYS USAGE NOTES See Previous Page Selected Channel “ChannelMenu” Displays the current channel. Press Scan Mode “ScnModeMenu” Use Press Talk group Lock Out “LockOutMenu” Use or to choose a talk group for locking/unlocking. Press (locked out) and off. Priority 2 Talk group “Priority2” Use or to choose Priority 2 talk group. Press to return to dwell display. Priority 1 Talk group “Priority1” Use or to choose Priority 1 talk group.
14221-1500-2000, Rev. K MENU NAME RADIO DISPLAYS USAGE NOTES See Previous Page Site Lock “Site Lock” OTP Software Version “Software Ver” RF Diagnostics “Diagnostics” Priority 3 Talk Group “Priority 3” Use or and off. Bluetooth “Bluetooth” See Section 8.9 below for Bluetooth operation. Use or Displays OTP software version Press to select site. to return to dwell display. Use or to scroll through RF diagnostics displays. Press diagnostics counters. Use 8.9 to scroll through sites.
14221-1500-2000, Rev. K 8.9.3 Delete a Device 1. Press or 2. Press . 3. Press or 4. Press . 8.9.4 to scroll through menu until SEL TO ENTER Bluetooth is displayed. to scroll through the menu until DELETE “Device Name” is displayed. Turn Off Bluetooth 1. Press or 2. Press . 3. Press or 4. Press .. 5. The to scroll through menu until SEL TO ENTER Bluetooth is displayed. to scroll through the menu until TURN OFF BLUETOOTH is displayed. indicator is no longer displayed. 8.
14221-1500-2000, Rev. K MESSAGE DESCRIPTION UNK DOM Unknown home domain. If condition persists in strong signal conditions, contact your system administrator. KEYSYNC Mismatched key sequence number. UNK ALG Unknown/unsupported encryption algorithm. BADSIZE Unsupported MDIS key size. NOAUT11 MES failed data mutual authentication. If condition persists in strong signal conditions, contact your system administrator. NOAUT12 No response from MDIS.
14221-1500-2000, Rev. K MESSAGE DESCRIPTION NO REG Not registered with MDIS, VNIC, or both. DISABLED Function disabled (e.g., function invalid in current context). 8.11 KEYPAD FUNCTION COMMANDS (SYSTEM MODEL ONLY) To perform a command from the keypad, use the keypad commands in Table 8-6. Table 8-6: Keypad Function Commands COMMANDS FUNCTION *0 Log-off command: *0## (logs the user off the system). *1 Login command: *1 # ## (required for encryption). *2 Status Message: *2 <0.
14221-1500-2000, Rev. K QUICK KEYS FUNCTION 3# Toggles Scan Mode On/Off (Normal/Fixed, see details below) • If the Scan Mode is Normal when the Scan Mode is toggled Off, the Scan Mode will be Normal when toggled On again. • If the Scan Mode is Fixed when the Scan Mode is toggled Off, the Scan Mode will be Fixed when scan mode is toggled On again. • If the Scan Mode is Off when the radio boots up, the Scan Mode will be Normal when Scan Mode is toggled On.
14221-1500-2000, Rev. K 2. Use or to scroll through the list of available profiles. 3. Profile becomes active when selected for longer than 2 seconds, when the is pressed, or when the menu is changed using the or button. Press to activate the selected profile. 8.16 CHANGING THE SELECTED TALK GROUP Each profile stored in the radio can have up to 16 talk groups. One talk group within the currently active profile is set as the “selected talk group.
14221-1500-2000, Rev. K 8.19 ADJUSTING SIDE TONE AUDIO LEVEL The radio sounds confirming tones called “side tones” when its buttons are pressed. Most users find this audible confirmation helpful when navigating the menus. Side tone audio level can be adjusted or turned completely off using the “Side Menu” or the Quick Key combination #4. Quick Key combination #4 turns off the backlight in addition to the side tones. Unlike Stealth Mode, alert tones can still be heard.
14221-1500-2000, Rev. K 8.21.1 Receiving a Voice Call No action is required to receive a voice call. The display responds to incoming voice calls as follows: • When the dwell display is set to received talk group and the scan mode is Normal or Fixed: a. If the received talk group matches the selected talk group, then the alias (if available) or user ID of the incoming caller is displayed. b. If the received talk group does not match the selected talk group, then the received talk group name is displayed.
14221-1500-2000, Rev. K NOTE Lock out is a listening (receive) function and only blocks received calls on locked out talk groups. Lock out does not affect transmit capability. “No Scan” and “Lock Out” do not apply to recent emergency lock outs. Only talk groups in the active profile can be locked out, since they are the only talk groups whose voice calls can be heard on the radio. Talk group lock out is a scan-related feature.
14221-1500-2000, Rev. K The choice of scanning mode broadens or narrows the span of communications with all the groups in profiles you listen to, but does not affect your interaction with those groups you talk with. The scanning modes available for selection may be limited to a subset of the three scanning modes by the administrator. Table 8-8: Scan Modes SCAN MODE None Normal (Default) Fixed EXPLANATION Eliminates distractions. Full communications (listen and talk) with the selected talk group.
14221-1500-2000, Rev. K • Priority 2 talk group. • Priority 3 talk group. • Other (non-priority). 8.24.3.1 Changing Scan Priority 1. Press the or keys until “Priority1” or “Priority2” appears in the display (Priority1 group has higher priority than the Priority2 group). 2. Press the or 3. Press the Display. key to select and activate the selection. The radio automatically returns to the Dwell • • NOTE button until the desired talk group is displayed.
14221-1500-2000, Rev. K Selective calls are terminated if an emergency is declared. The network limits selective calls to 10 minutes maximum. NOTE If a Selective Call is attempted without registration, “No Priv” is displayed. NOTE 8.25.1 Manually Dialing a Selective Call (System Model Only) 1. Enter *8, the User ID number of the user being called, and the # key (no dashes or spaces). Note that this feature must be enabled by the administrator.
14221-1500-2000, Rev. K 8.25.2 Selective Call Using Speed Dial Speed dial numbers are defined and provisioned by the OpenSky network administrator and cannot be manually entered into the radio by the user. Contact the administrator if changes to the speed dial list are required. NOTE • Scroll through the Menu options using the or button until “Speed Dial” appears in the second line of the display.
14221-1500-2000, Rev. K 8.26.1 Defining Messages All selective alert messages are pre-defined. The messages are programmed and provisioned remotely by your OpenSky system administrator. The radio user cannot create selective alert message content. The entire selective alert message, including the abbreviation, can be up to 99 characters long. Table 8-10 lists and defines the messages that may be displayed by the radio during a Selective Alert.
14221-1500-2000, Rev. K 8.26.2.2 Selecting a Destination Using the Menu 1. Using the or 2. Use the or and press the 3. Use the displayed. 4. Press the key, scroll through the menu until “AlertDst” (Alert Destination) appears. button to scroll through the list of User IDs until the desired destination is displayed key. or buttons to scroll through the available messages until the desired message is key to send the message. 5. Observe Status Messages (Table 8-10) to ensure proper delivery. 8.26.
14221-1500-2000, Rev. K 8.28 EMERGENCY COMMUNICATIONS The XG-25P portable radio is capable of sending an emergency alert and making emergency calls on the network. The OpenSky system handles emergency calls with the highest priority, allowing you or the people you serve to get needed help. Emergency call and alert capability for a profile is configured by the system administrator. The radio that initiates an emergency alert emits a signal of three distinct beeps that only goes to the dispatch console.
14221-1500-2000, Rev. K If the attempt is unsuccessful, “E-PEND” flashes periodically and a retry is queued for 10 seconds. If unsuccessful because of lost sync, retry occurs immediately upon reacquiring sync. On each retry attempt, the radio temporarily displays “E-RETRY.” This process repeats until the emergency is successfully declared. 8.28.2 Receiving an Emergency Call When receiving an emergency call, the radio sounds the emergency tone (three short high-pitched tones).
14221-1500-2000, Rev. K 8.29 OPENSKY ENCRYPTION In the OpenSky network, both data and voice use a 128-bit or 256-bit key encryption standard published by the Federal Information Processing Service (FIPS), called Advanced Encryption Standard (AES). AES is approved by the U.S. Department of Commerce for encryption of classified materials. When encryption is enabled on the network, data is encrypted from the MDIS to the Mobile End System (MES) (e.g., XG-25P portable radio).
14221-1500-2000, Rev. K NOTE The key must be pre-determined by the users prior to making a manually encrypted call on a talk group and is entered into the radio using the keypad. For 128 bit encryption, this key is between 1 and 16 digits. For 256 bit encryption, this key is between 17 and 32 digits. 8.29.2.1 Using Manual Encryption 1. Press *32 on the keypad. 2. Enter the key (1 – 16 digits for 128 bit encryption; 17 – 32 digits for 256 bit encryption). 3. Press #. 4.
14221-1500-2000, Rev. K 3. Press the button to send the currently selected message. If no messages have been configured, no message is sent and an error tone sounds. Press or to cancel status message selection. 8.31 REQUEST TO TALK (RTT) MESSAGES If enabled via programming, the RTT message feature allows you to send a short service message to the VNIC. Section 8.31.1 describes how to send an RTT message via the keypad and Section 8.31.2 describes how to send an RTT message via the menu.
14221-1500-2000, Rev. K 8.33 GPS COORDINATES The radio’s current latitude and longitude coordinates may be displayed using the “GPS” menu. The following procedure assumes a GPS antenna is connected to the radio and it is receiving adequate signals from GPS satellites. 1. Press or until the “GPS” menu appears in the display. Current GPS coordinate latitude and longitude data continuously scrolls in the top line of the display in a degrees:minutes:seconds format. 2.
14221-1500-2000, Rev. K 8.34.3 Radio Limitations Using Extended Coverage Modes Connecting a portable radio to a V-TAC introduces minor functional limitations. See the following sections for a listing. 8.34.3.1 Limitations Using XCOV, XCOV-TG, and XCOV-PROF Portable radios connected to the V-TAC using any of the Extended Coverage Modes, XCOV, XCOV-TG, or XCOV-PROF, will not channel-scan unless they lose radio frequency contact with the V-TAC. If manually enabled, radios will not scan network channels. 8.
14221-1500-2000, Rev. K 8.34.5 Use XCOV-TG Mode When using the XCOV-TG mode, up to 30 client radios can connect to the V-TAC. However, unlike XCOV, radios connected using XCOV-TG are limited to communicating only on the XCOV-TG talk group. The radio can only raise an emergency if this talk group is emergency capable. Advanced features such as selective calling and mobile data operations are not available to the XCOV-TG connected clients.
14221-1500-2000, Rev. K • The client profile used to connect to the V-TAC must have been previously provisioned to the client prior to connection. If the profile is not in the client’s personality, the client cannot connect to the VTAC. • Neither the V-TAC nor a client can change the profile once it has entered XCOV-PROF mode. The Profile menu will be disabled. • Client global profiles are disabled. 8.34.6.
14221-1500-2000, Rev. K 5. Press or to edit the right-most digit and press desired channel is entered. to advance to the next digit. Repeat until the 6. The radio then prompts the user to edit the band. Table 8-12 lists valid bands and their definitions. Press or to edit the number assigned to the frequency band and press to confirm and enter the SOI mode. Use the Client Mode menu to return to normal operation (Network Mode).
14221-1500-2000, Rev. K 9. MARITIME FREQUENCIES Refer to Table 9-1 for a list of maritime frequencies per United States Coast Guard (USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department Fisheries and Oceans. • United States (US) • International (Intl) • Canada (CA) Table 9-1: Maritime Frequencies CHANNEL US INTL 1 CA 1 1a CHANNEL USAGE T: 156.05 R: 160.65 T: 160.65 R: 156.05 International: Public Correspondence, Port Operations. T/R: 156.05 T/R: 156.
14221-1500-2000, Rev. K Table 9-1: Maritime Frequencies CHANNEL US INTL CA FREQUENCY SHIP SHORE (MHz) (MHz) CHANNEL USAGE 11 11 11 T/R: 156.55 T/R: 156.55 US: Commercial. VTS in selected areas. International: Port Operations. Canada: VTS - British Columbia coast area. Also used for pilotage purposes. 12 12 12 T/R: 156.60 T/R: 156.60 US: Port Operations. VTS in selected areas. International: Port Operations. Canada: VTS - British Columbia coast area. Also used for pilotage purposes.
14221-1500-2000, Rev. K Table 9-1: Maritime Frequencies CHANNEL US INTL CA 21 21a 23 CHANNEL USAGE T: 157.05 R: 161.65* T: 161.65* R: 157.05 International: Public Correspondence, Port Operations. 21a T/R: 157.05 T/R: 157.05 US: US Coast Guard only. Canada: DFO/Canadian Coast Guard only. 21b -- T/R: 161.65 Canada: Continuous Marine Broadcast (CMB) service (weather). T: 157.10 R: 161.70 T: 161.70 R: 157.10 International: Public Correspondence, Port Operations. 22a T/R: 157.10 T/R: 157.
14221-1500-2000, Rev. K Table 9-1: Maritime Frequencies CHANNEL US INTL CA 63 63a 64 T: 160.775 R: 156.175 International: Public Correspondence, Port Operations. 63a T/R: 156.175 T/R: 156.175 US: Port Operations and Commercial, VTS. New Orleans/Lower Mississippi area. Canada: Tow Boats - British Columbia coast area. 64 T: 156.225 R: 160.825 T: 160.825 R: 156.225 International: Public Correspondence, Port Operations. 64a T/R: 156.225 T/R: 156.225 Canada: Commercial fishing only. T: 156.
14221-1500-2000, Rev. K Table 9-1: Maritime Frequencies CHANNEL US INTL CA FREQUENCY SHIP SHORE (MHz) (MHz) CHANNEL USAGE 73 73 73 T/R: 156.675 T/R: 156.675 US: Port Operations. International: Intership, Port Operations. Canada: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. Commercial fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta areas. 74 74 74 T/R: 156.725 T/R: 156.
14221-1500-2000, Rev. K Table 9-1: Maritime Frequencies CHANNEL US INTL FREQUENCY SHIP SHORE (MHz) (MHz) CA CHANNEL USAGE 83b -- T/R: 161.775 Canada: Continuous Marine Broadcast (CMB) service (weather). 84 84 84 T: 157.225 R: 161.825 T: 161.825 R: 157.225 US: Public Correspondence (Marine Operator). International: Public Correspondence, Port Operations. 85 85 85 T: 157.275 R: 161.875 T: 161.875 R: 157.275 US: Public Correspondence (Marine Operator).
14221-1500-2000, Rev. K 10. BASIC TROUBLESHOOTING Use Table 10-1 as a troubleshooting guide if the radio is not functioning properly. If additional assistance is required, contact a qualified service technician or call Harris at 1-800-528-7711. Table 10-1: Troubleshooting SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION Radio will not turn on. Low battery charge. Change the battery pack to a fully charged pack. No Audio. Speaker volume is muted. Increase the volume level. Poor Audio.
14221-1500-2000, Rev. K 11. CUSTOMER SERVICE 11.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
14221-1500-2000, Rev. K 12. WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at the Customer Care center webpage: http://www.pspc.harris.com/Service/Customerservice.aspx. While on the webpage, please review the applicable battery and/or product warranty literature.
14221-1500-2000, Rev. K APPENDIX A- CONFIGURING ENCRYPTION Refer to the following documentation for advanced programming and setup instructions: A.
14221-1500-2000, Rev. K c. Scroll through and select the HKL option and press the keys from the Harris Keyloader. button. The radio can now accept 5. Load the UKEK file from the Crypto Officer onto the PC. 6. Run the RPM application and setup the radio’s Personality according the SLN Binding Report information. 7. Setup the talk groups and the SLN mappings (Talk Group ID to SLN). This includes mapping SLNs to the “System” keys (PSTN, All Call, etc.). 8.
14221-1500-2000, Rev. K a. Press the radio’s button. b. Scroll through the menu to select the KEYLOAD option and press the c. Scroll through and select the HKL option and press the keys from the Harris Keyloader. button to activate. button. The radio can now accept 12. Select Radio from the drop-down and click Load. 13. Click Finish. A.2.3 Power on the Motorola KVL Device 1. Connect KVL Device to the radio using cable 14002-0143-01.
Public Safety and Professional Communications | www.pspc.harris.