Installation Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 Federal Communications Commission Regulations
- 1.4 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.5 REGULATORY APPROVALS
- 1.6 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.7 COMMON HAZARDS
- 1.8 SAFE DRIVING RECOMMENDATIONS
- 1.9 OPERATING RULES AND REGULATIONS
- 1.10 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. SPECIFICATIONS0F
- 4. OPTIONS AND ACCESSORIES
- 5. INTRODUCTION
- 6. INSTALLATION PROCESS
- 6.1 GENERAL INFORMATION
- 6.2 PRE-INSTALLATION VEHICLE CHECK
- 6.3 PLANNING THE INSTALLATION
- 6.4 WIRING and CABLING REQUIREMENTS
- 6.5 TOOLS REQUIRED
- 6.6 UNPACKING AND CHECKING THE EQUIPMENT
- 7. ANTENNA INSTALLATION
- 7.1 ANTENNA MOUNTING LOCATIONS
- 7.2 RF ANTENNA INSTALLATION PROCEDURES
- 7.2.1 Installing Antenna Mounts AN-125001-002, -004, and -006
- 7.2.2 Installing Magnetic Antenna Mount AN-125001-008 and 12099-0370-01
- 7.2.3 Installing All Other Antenna Mounts
- 7.2.4 Attaching the NMO Antenna Element
- 7.2.5 Installing the Coax Cable and TNC RF Connector
- 7.2.6 Install GPS Antenna (If Required)
- 7.2.7 Installing a GPS Combo Antenna
- 7.2.8 Installing a GPS Antenna Inside the Rear-Deck
- 8. FRONT-MOUNT RADIO INSTALLATION
- 9. REMOTE-MOUNT RADIO INSTALLATION
- 9.1 MOUNTING THE REMOTE-MOUNT RADIO
- 9.2 REMOTE-MOUNT RADIO’S WIRING AND CABLING
- 9.3 CONTROL HEAD INSTALLATION
- 10. OPTION AND ACCESSORY INSTALLATION
- 11. CABLES AND CONNECTIONS
- 12. INSTALLATION INSPECTION AND TESTS
- 13. CARING FOR THE RADIO EQUIPMENT
- 14. CUSTOMER SERVICE
- 15. INSTALLATION CHECKLIST
- 16. WARRANTY REGISTRATION
14221-1850-4000, Rev. A
34
6.5 TOOLS REQUIRED
The following tools are recommended to complete the installation. Where specific vendor names and model
or part numbers are given, equivalent substitutes may be used:
•
Non-Insulated Crimp Tool: Thomas & Betts
®
WT-111-M
•
Phillips-Head Screwdrivers, #1 and #2
•
Flat-Blade Screwdrivers, ⅛-inch & ¼-inch tips
•
Insulated Terminal Crimp Tool: Klein 1005
•
2.5-Millimeter Allen Wrench or Hex Bit
•
Titan 11955 Ratcheting Heat Shrink Terminal
Crimper (or Equivalent)
•
7-Millimeter Hex Socket or Socket Bit
•
3-Blade Coax Cable Stripper for RG-58 Cable
similar to Tyco Electronics 1490490-1
(includes blades)
•
⅛-Inch Hex Key Wrench (Allen Wrench)
•
5
/
16
-Inch Combination or Open-End Wrench
(Only Needed for GPS Receiver Option)
•
Ratcheting Hex-Crimp Tool for 50-Ohm TNC
and BNC RF Connectors and RG-58 Cable
similar to Tyco Electronics 58433-2 (includes
Crimper 354940-1 and Die Set 58436-1) or
Emerson Network Power 24-9960P
•
¾-Inch or ⅜-Inch Hole Saw with Depth
Protection: ¾-Inch = Ripley HSK 19 or
Antenex HS34; ⅜-Inch = Antenex HS38
•
Clutch-Type Cordless Drill with Drill Bits and
Driver Bits
•
Non-Metallic Fish Tape, 25-Foot: Klein-Lite
50156
•
Deburring Tool (for ⅜-inch and smaller holes)
•
Flush-Cut and Large Wire Cutters
•
Various Socket and Driver Sets
•
Various Fasteners (e.g., machine screws and
nuts, Tek screws, etc.)
•
Soft-Jaw Pliers: Tessco 450520 or equivalent
•
Tie Wraps: Nylon, 6-inches or larger
•
Heat Gun
•
Heat Shrink