Installation Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 Federal Communications Commission Regulations
- 1.4 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.5 REGULATORY APPROVALS
- 1.6 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.7 COMMON HAZARDS
- 1.8 SAFE DRIVING RECOMMENDATIONS
- 1.9 OPERATING RULES AND REGULATIONS
- 1.10 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. SPECIFICATIONS0F
- 4. OPTIONS AND ACCESSORIES
- 5. INTRODUCTION
- 6. INSTALLATION PROCESS
- 6.1 GENERAL INFORMATION
- 6.2 PRE-INSTALLATION VEHICLE CHECK
- 6.3 PLANNING THE INSTALLATION
- 6.4 WIRING and CABLING REQUIREMENTS
- 6.5 TOOLS REQUIRED
- 6.6 UNPACKING AND CHECKING THE EQUIPMENT
- 7. ANTENNA INSTALLATION
- 7.1 ANTENNA MOUNTING LOCATIONS
- 7.2 RF ANTENNA INSTALLATION PROCEDURES
- 7.2.1 Installing Antenna Mounts AN-125001-002, -004, and -006
- 7.2.2 Installing Magnetic Antenna Mount AN-125001-008 and 12099-0370-01
- 7.2.3 Installing All Other Antenna Mounts
- 7.2.4 Attaching the NMO Antenna Element
- 7.2.5 Installing the Coax Cable and TNC RF Connector
- 7.2.6 Install GPS Antenna (If Required)
- 7.2.7 Installing a GPS Combo Antenna
- 7.2.8 Installing a GPS Antenna Inside the Rear-Deck
- 8. FRONT-MOUNT RADIO INSTALLATION
- 9. REMOTE-MOUNT RADIO INSTALLATION
- 9.1 MOUNTING THE REMOTE-MOUNT RADIO
- 9.2 REMOTE-MOUNT RADIO’S WIRING AND CABLING
- 9.3 CONTROL HEAD INSTALLATION
- 10. OPTION AND ACCESSORY INSTALLATION
- 11. CABLES AND CONNECTIONS
- 12. INSTALLATION INSPECTION AND TESTS
- 13. CARING FOR THE RADIO EQUIPMENT
- 14. CUSTOMER SERVICE
- 15. INSTALLATION CHECKLIST
- 16. WARRANTY REGISTRATION
14221-1850-4000, Rev. A
39
Table 7-1: Recommended Antenna Mounting Locations with Antenna Part Numbers
TOP VIEW OF A TYPICAL VEHICLE
ANTENNA
LOCATION(S)
•
Ž
•
Œ
Antennas listed in Section 4.
ü
ü ü
GPS receive-only antennas.
ü ü ü
7.2 RF ANTENNA INSTALLATION PROCEDURES
An antenna must be installed before completing the radio installation.
Section 4 lists the mobile radio antennas available for use with the radio. As presented in the previous
section, various mounting locations exist. Optimal performance is achieved via a rooftop antenna mounted
in the direct center of the motor vehicle’s roof.
7.2.1 Installing Antenna Mounts AN-125001-002, -004, and -006
These NMO style antenna mounts can each be used with several different antenna elements. Only limited
access under the mounting location is typically required. The installation procedure is presented in Section
7.2.1.3.
7.2.1.1 Standard Antenna Mounts AN-125001-002 and -006
This standard ¾-inch NMO antenna mount requires a ¾-inch hole in a relatively flat area of the vehicle
body, with a vehicle metal thickness of between 0.020 and 0.040 inches.
7.2.1.2 Thick-Roof Antenna Mount AN-125001-004
This thick-roof NMO antenna mount uses a ⅜-inch or a ¾-inch mounting hole in a relatively flat area of
the vehicle body, with a vehicle metal thickness of between 0.040 and 0.1875 inches (
3
/16-inch maximum
thickness).
NOTE