Installation Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 Federal Communications Commission Regulations
- 1.4 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.5 REGULATORY APPROVALS
- 1.6 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.7 COMMON HAZARDS
- 1.8 SAFE DRIVING RECOMMENDATIONS
- 1.9 OPERATING RULES AND REGULATIONS
- 1.10 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. SPECIFICATIONS0F
- 4. OPTIONS AND ACCESSORIES
- 5. INTRODUCTION
- 6. INSTALLATION PROCESS
- 6.1 GENERAL INFORMATION
- 6.2 PRE-INSTALLATION VEHICLE CHECK
- 6.3 PLANNING THE INSTALLATION
- 6.4 WIRING and CABLING REQUIREMENTS
- 6.5 TOOLS REQUIRED
- 6.6 UNPACKING AND CHECKING THE EQUIPMENT
- 7. ANTENNA INSTALLATION
- 7.1 ANTENNA MOUNTING LOCATIONS
- 7.2 RF ANTENNA INSTALLATION PROCEDURES
- 7.2.1 Installing Antenna Mounts AN-125001-002, -004, and -006
- 7.2.2 Installing Magnetic Antenna Mount AN-125001-008 and 12099-0370-01
- 7.2.3 Installing All Other Antenna Mounts
- 7.2.4 Attaching the NMO Antenna Element
- 7.2.5 Installing the Coax Cable and TNC RF Connector
- 7.2.6 Install GPS Antenna (If Required)
- 7.2.7 Installing a GPS Combo Antenna
- 7.2.8 Installing a GPS Antenna Inside the Rear-Deck
- 8. FRONT-MOUNT RADIO INSTALLATION
- 9. REMOTE-MOUNT RADIO INSTALLATION
- 9.1 MOUNTING THE REMOTE-MOUNT RADIO
- 9.2 REMOTE-MOUNT RADIO’S WIRING AND CABLING
- 9.3 CONTROL HEAD INSTALLATION
- 10. OPTION AND ACCESSORY INSTALLATION
- 11. CABLES AND CONNECTIONS
- 12. INSTALLATION INSPECTION AND TESTS
- 13. CARING FOR THE RADIO EQUIPMENT
- 14. CUSTOMER SERVICE
- 15. INSTALLATION CHECKLIST
- 16. WARRANTY REGISTRATION
14221-1850-4000, Rev. A
77
Ethernet Cable
Control
Head #1
(e.g., at main
operator location)
Ethernet Cable
Ethernet
Connector on
Rear of Radio
ETH
ETH
Mobile
Radio
ETH
Ethernet Connectors
on Rear of
Control Head
(2 places, this head)
ETH
ETH
Control
Head #2
(e.g., near rear of
vehicle)
Figure 9-13: Ethernet Connections for Multiple-Control Head Installation
If the mobile radio installation must be interfaced to other equipment that is mounted
near the Control Head, simultaneous routing of the related interface cables along with
the Ethernet cable saves time.
2. Mate one end of the Ethernet cable to the other Ethernet connector on the rear panel of the Control
Head.
3. If not already mated, mate the other end of the Ethernet cable to the Ethernet connector on the rear
panel of the radio.
4. Any necessary option/accessory cables from the back of the radio can also be routed with this wire and
cable within the vehicle’s interior (i.e., up to but not through the vehicle’s firewall).
5. Loop, tie, and stow the cable(s) as necessary, leaving a service loop at the back of the radio and at the
back of the Control Head. Protect the entire length of the cable(s) and wire(s) from possible chafing.
NOTE